Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2013.12–2015.11
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0097860 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Front Wiper Motor Circuit  


DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly.

WIRING DIAGRAM

E287932E01
0.635,0.385 1.583,0.719 0.948,0.333 10 false from IG1 NO. 1 Relay 1.896,0.542 2.844,0.708 0.948,0.167 10 false WIPER FR 2.979,0.385 3.229,0.552 0.25,0.167 10 false 4A 2.99,0.833 3.24,1 0.25,0.167 10 false 4F 3.01,0.635 3.177,0.802 0.167,0.167 10 false 1 2.99,0.188 3.344,0.385 0.354,0.198 10 false 10 0.344,2.208 3.146,2.563 2.802,0.354 10 false Instrument Panel Junction Block Assembly 0.333,5.25 0.667,5.469 0.333,0.219 10 false A32 0.333,5.417 2.5,5.583 2.167,0.167 10 false Windshield Wiper Motor Assembly 5.583,4.906 5.917,5.073 0.333,0.167 10 false F79 5.583,5.083 7.083,5.417 1.5,0.333 10 false Windshield Wiper Relay Assembly 5.531,2.073 5.865,2.24 0.333,0.167 10 false F64 5.823,4.031 6.073,4.198 0.25,0.167 10 false 11 5.531,2.25 7.083,2.583 1.552,0.333 10 false Windshield Wiper Switch Assembly 5.875,3.125 6.042,3.292 0.167,0.167 10 false 1 6.115,4.146 6.365,4.313 0.25,0.167 10 false +2 6.083,3.219 6.5,3.385 0.417,0.167 10 false +SM 6.094,1.313 6.344,1.479 0.25,0.167 10 false +2 5.885,1.219 6.052,1.385 0.167,0.167 10 false 4 5.885,1.708 6.052,1.875 0.167,0.167 10 false 3 5.896,0.281 6.063,0.448 0.167,0.167 10 false 2 6.094,1.802 6.344,1.969 0.25,0.167 10 false +1 6.094,0.375 6.344,0.542 0.25,0.167 10 false +B 2.063,4.031 2.313,4.198 0.25,0.167 10 false +2 2.063,3.49 2.313,3.656 0.25,0.167 10 false +1 2.042,3.115 2.292,3.281 0.25,0.167 10 false +S 2.125,2.729 2.292,2.896 0.167,0.167 10 false B 2.125,4.833 2.292,5 0.167,0.167 10 false E 2.354,4.833 2.521,5 0.167,0.167 10 false 4 2.354,4.031 2.521,4.198 0.167,0.167 10 false 3 2.354,3.49 2.521,3.656 0.167,0.167 10 false 5 2.354,3.115 2.521,3.281 0.167,0.167 10 false 1 2.354,2.729 2.521,2.896 0.167,0.167 10 false 2 6.115,3.604 6.531,3.771 0.417,0.167 10 false IG 5.885,3.5 6.052,3.667 0.167,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - IG CIRCUIT)
a.

Disconnect the A32 windshield wiper motor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-2 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
a.

Remove the windshield wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


b.
E257561C01
1.396,0.854 0.896,0.313 false 2.385,1.781 1.885,1.24 false 1.052,1.719 1.573,1.24 false 0.115,0.135 0.427,0.333 0.313,0.198 10 false *a 0.781,0.135 1.094,0.333 0.313,0.198 10 false +2 0.906,1.76 1.219,1.958 0.313,0.198 10 false +1 2.417,1.813 2.729,2.01 0.313,0.198 10 false E
*a Component without harness connected
(Windshield Wiper Motor Assembly)


Check the LO operation.

i.

Connect a battery positive (+) lead to terminal 5 (+1) and a negative (-) lead to terminal 4 (E), and check that the motor operates at low speed.

OK:

Motor operates at low speed (LO).




c.

Check the HI operation.

i.

Connect a battery positive (+) lead to terminal 3 (+2) and a negative (-) lead to terminal 4 (E), and check that the motor operates at high speed.

OK:

Motor operates at high speed (HI).




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)
a.

Disconnect the F79 windshield wiper relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-1 (+S) - F79-1 (+SM) Always Below 1 Ω
A32-1 (+S) or F79-1 (+SM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)
a.

Disconnect the F64 windshield wiper switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-3 (+2) - F79-11 (+2) Always Below 1 Ω
A32-3 (+2) or F79-11 (+2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-5 (+1) - F64-3 (+1) Always Below 1 Ω
A32-3 (+2) - F64-4 (+2) Always Below 1 Ω
A32-5 (+1) or F64-3 (+1) - Body ground Always 10 kΩ or higher
A32-3 (+2) or F64-4 (+2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-2 (B) - 4F-1 Always Below 1 Ω
A32-2 (B) or 4F-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR