Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2013.12–2015.11
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0097860 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rain Sensor Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a signal from the rain sensor via LIN communication to control the auto wiper system.

WIRING DIAGRAM

E288754
5.427,2.844 6.927,3.229 1.5,0.385 10 false Windshield Wiper Relay Assembly 3.844,2.813 4.635,3.052 0.792,0.24 10 false Rain Sensor 3.844,2.656 4.135,2.833 0.292,0.177 10 false S13 5.406,2.677 5.698,2.854 0.292,0.177 10 false F79 3.896,2.063 4.188,2.24 0.292,0.177 10 false ES 3.885,0.927 4.177,1.104 0.292,0.177 10 false SIG 4.313,1.479 4.667,1.656 0.354,0.177 10 false MPX 5.74,1.49 6.146,1.667 0.406,0.177 10 false MPX1 5.5,1.333 5.719,1.531 0.219,0.198 10 false 14 4.708,1.333 4.927,1.531 0.219,0.198 10 false 1 3.708,0.802 3.927,1 0.219,0.198 10 false 4 3.719,1.958 3.938,2.156 0.219,0.198 10 false 2 3.052,0.781 3.271,0.979 0.219,0.198 10 false 50 0.917,3.302 2.896,3.5 1.979,0.198 10 false : LIN Communication Line 0.531,0.906 1.49,1.25 0.958,0.344 10 false from IG1 NO. 2 Relay 2.24,1.052 2.927,1.26 0.688,0.208 10 false ECU-IG 0.458,1.771 3.385,2.135 2.927,0.365 10 false Instrument Panel Junction Block Assembly 0.448,1.635 1.135,1.844 0.688,0.208 10 false 4A

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - IG CIRCUIT AND BODY GROUND)
a.
E267170C08
1.479,0.344 1.885,0.615 0.406,0.271 1.948,1.354 2.448,1.656 false 1.583,1.354 1.073,1.688 false 0.135,0.156 0.448,0.354 0.313,0.198 10 false *a 0.948,1.719 1.26,1.917 0.313,0.198 10 false ES 2.396,1.677 2.76,1.875 0.365,0.198 10 false SIG 1.573,0.385 2.031,0.583 0.458,0.198 10 false S13
*a Front view of wire harness connector
(to Rain Sensor)


Disconnect the S13 rain sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S13-4 (SIG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S13-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - RAIN SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - RAIN SENSOR)
a.

Disconnect the F79 windshield wiper relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-14 (MPX1) - S13-1 (MPX) Always Below 1 Ω
F79-14 (MPX1) or S13-1 (MPX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RAIN SENSOR
a.
E257042C01
1.969,0.958 2.521,0.406 false 1.802,0.958 1.115,0.406 false 0.156,0.177 0.469,0.375 0.313,0.198 10 *a 0.969,0.188 1.281,0.385 0.313,0.198 10 ES 2.438,0.198 2.875,0.406 0.438,0.208 10 MPX
*a Component with harness connected
(Rain Sensor)


Connect the S13 rain sensor connector.


b.

Connect an oscilloscope to the rain sensor connector.


c.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
1 (MPX) - 2 (ES) Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S13-4 (SIG) - 4A-50 Always Below 1 Ω
S13-4 (SIG) or 4A-50 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR