The main body ECU (multiplex network body ECU) receives switch signals from the power window regulator master switch assembly and driver door key cylinder lock or unlock switch signals from the front door lock with motor assembly. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.
for LHD
for RHD
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*
*: w/ Smart Entry and Start System
The power door lock control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: for LHD
Check door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| All doors cannot be locked by power window regulator master switch assembly | A |
| All doors cannot be locked by driver door key cylinder | B |
A
B
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs.
DTC B1206 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that all doors can be locked and unlocked by the power window regulator master switch assembly.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
All doors can be locked and unlocked by the power window regulator master switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Key SW-Lock | Driver door key-linked lock/unlock switch lock signal | OFF or ON | OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position |
- |
| D Door Key SW-UL | Driver door key-linked lock / unlock switch unlock signal | OFF or ON | OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position |
- |
| Tester Display |
|---|
| Door Key SW-Lock |
| D Door Key SW-UL |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Remove the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
for RHD
Remove the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the F19 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I14-9 (L) - F19-29 (L2) | Always | Below 1 Ω |
| I14-10 (UL) - F19-2 (UL3) | Always | Below 1 Ω |
| I14-7 (E) - Body ground | Always | Below 1 Ω |
| I14-9 (L) or F19-29 (L2) - Body ground | Always | 10 kΩ or higher |
| I14-10 (UL) or F19-2 (UL3) - Body ground | Always | 10 kΩ or higher |
for RHD
Disconnect the F19 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H15-6 (L) - F19-29 (L2) | Always | Below 1 Ω |
| H15-5 (UL) - F19-2 (UL3) | Always | Below 1 Ω |
| H15-8 (E) - Body ground | Always | Below 1 Ω |
| H15-6 (L) or F19-29 (L2) - Body ground | Always | 10 kΩ or higher |
| H15-5 (UL) or F19-2 (UL3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG