Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098502 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiplex network body ECU) sends an unlock warning switch signal and driver door courtesy light switch signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

for LHD


B364847
0.927,0.688 1.24,0.885 0.313,0.198 10 false M1 0.948,1.833 1.26,2.031 0.313,0.198 10 false F52 0.927,0.833 2.552,1.25 1.625,0.417 10 false Front Door Courtesy Light Switch Assembly (for LH) 0.938,2 2.438,2.417 1.5,0.417 10 false Unlock Warning Switch Assembly 2.313,1.521 2.5,1.719 0.188,0.198 10 false 1 1.104,1.521 1.292,1.719 0.188,0.198 10 false 2 2.313,0.354 2.5,0.552 0.188,0.198 10 false 1 1.281,1.531 1.594,1.729 0.313,0.198 10 false UN- 1.948,1.531 2.26,1.729 0.313,0.198 10 false UN+ 3.052,1.427 3.365,1.625 0.313,0.198 10 false 28 4.031,0.271 4.219,0.49 0.188,0.219 10 false 6 4.031,1.417 4.198,1.625 0.167,0.208 10 false 3 3.042,1.635 3.354,1.833 0.313,0.198 10 false 4D 3.969,1.635 4.281,1.833 0.313,0.198 10 false MB 3.948,0.479 4.26,0.677 0.313,0.198 10 false F19 4.354,1.635 4.927,1.875 0.573,0.24 10 false KSW 4.354,0.479 4.927,0.719 0.573,0.24 10 false FLCY 5.875,2.708 7.073,3.177 1.198,0.469 10 false Combination Meter Assembly 4.292,2.708 5.448,3.219 1.156,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 2.635,2.458 4.25,2.885 1.615,0.427 10 false Instrument Panel Junction Block Assembly 0.865,3.354 2.615,3.594 1.75,0.24 10 false : CAN Communication Line


for RHD


B364847
0.927,0.688 1.24,0.885 0.313,0.198 10 false L1 0.948,1.833 1.26,2.031 0.313,0.198 10 false F52 0.927,0.833 2.552,1.25 1.625,0.417 10 false Front Door Courtesy Light Switch Assembly (for RH) 0.938,2 2.438,2.417 1.5,0.417 10 false Unlock Warning Switch Assembly 2.313,1.521 2.5,1.719 0.188,0.198 10 false 1 1.104,1.521 1.292,1.719 0.188,0.198 10 false 2 2.313,0.354 2.5,0.552 0.188,0.198 10 false 1 1.281,1.531 1.594,1.729 0.313,0.198 10 false UN- 1.948,1.531 2.26,1.729 0.313,0.198 10 false UN+ 3.052,1.427 3.365,1.625 0.313,0.198 10 false 28 4,0.271 4.188,0.49 0.188,0.219 10 false 27 4.031,1.417 4.198,1.625 0.167,0.208 10 false 3 3.042,1.635 3.354,1.833 0.313,0.198 10 false 4D 3.969,1.635 4.281,1.833 0.313,0.198 10 false MB 3.948,0.479 4.26,0.677 0.313,0.198 10 false F19 4.354,1.635 4.927,1.875 0.573,0.24 10 false KSW 4.354,0.479 4.927,0.719 0.573,0.24 10 false FRCY 5.875,2.708 7.073,3.177 1.198,0.469 10 false Combination Meter Assembly 4.292,2.708 5.448,3.219 1.156,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 2.635,2.458 4.25,2.885 1.615,0.427 10 false Instrument Panel Junction Block Assembly 0.865,3.354 2.615,3.594 1.75,0.24 10 false : CAN Communication Line


CAUTION / NOTICE / HINT

NOTICE:
·

The key reminder warning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the key reminder warning system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Turn the ignition switch to ON. Place luggage on the front passenger seat to cause the seat belt warning light to blink.


b.

When driving the vehicle at 20 km/h (12 mph) or higher, check that the seat belt warning buzzer sounds to inform that the front passenger seat belt is not fastened.

HINT:

The key reminder warning system sounds the buzzer built into the combination meter assembly as a key reminder warning. This buzzer is also used for the seat belt warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the seat belt is not fastened.


OK:

Combination meter buzzer sounds.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FR Door Courtesy SW, FL Door Courtesy SW)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (FR Door Courtesy SW, FL Door Courtesy SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly (for RH) signal OFF or ON OFF: Front door RH closed
ON: Front door RH open
*1
FL Door Courtesy SW Front door courtesy light switch assembly (for LH) signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
*2

*1: for RHD

*2: for LHD


Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

The GTS indicates ON or OFF according to the driver door conditions shown in the table.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (Key Unlock Warning SW)

NG

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (Key Unlock Warning SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal OFF or ON OFF: No key in ignition key cylinder
ON: Key in ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

The GTS indicates ON or OFF according to whether the key is in the ignition key cylinder.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-28 - F52-1 (UN+) Always Below 1 Ω
F52-2 (UN-) - Body ground Always Below 1 Ω
F52-1 (UN+) or 4D-28 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B346817
2.083,0.917 2.385,1.135 0.302,0.219 5.5,0.688 5.802,0.896 0.302,0.208 0.917,2.177 0.708,2.177 0.708,2.177 0.708,1.604 false 0.271,0.25 0.583,0.448 0.313,0.198 10 false *a 2.135,0.938 2.448,1.135 0.313,0.198 10 false MB 5.573,0.698 5.885,0.896 0.313,0.198 10 false 4D 0.979,2.094 1.438,2.292 0.458,0.198 10 false KSW
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-28 - MB-3 (KSW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

for LHD

i.

Remove the front door courtesy light switch assembly (for LH).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


ii.

Inspect the front door courtesy light switch assembly (for LH).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION



b.

for RHD

i.

Remove the front door courtesy light switch assembly (for RH).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


ii.

Inspect the front door courtesy light switch assembly (for RH).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

B

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for LH)

C

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for RH)

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

for LHD

i.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-1 - F19-6 (FLCY) Always Below 1 Ω
M1-1 or F19-6 (FLCY) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L1-1 - F19-27 (FRCY) Always Below 1 Ω
L1-1 or F19-27 (FRCY) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR