Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM3160E _58 Vehicle Interior _019713 SEAT BELT _0100669 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly illuminates, blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly LH.

WIRING DIAGRAM

B289103E20
5.146,1.917 7.094,2.292 1.948,0.375 10 false Front Seat Inner Belt Assembly (Driver Seat) 5.146,1.75 6.115,1.938 0.969,0.188 10 false M4*1, L5*2 3.156,1.917 4.76,2.198 1.604,0.281 10 false Airbag Sensor Assembly 5.052,4.313 6.865,4.542 1.813,0.229 10 false : CAN Communication Line 0.26,1.75 1.958,2.167 1.698,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.229,4.229 2.073,4.49 1.844,0.26 10 false Combination Meter Assembly 3.167,1.75 4.021,1.979 0.854,0.229 10 false M7*1, L9*2 5.365,1.094 5.51,1.323 0.146,0.229 10 false 1 5.365,0.292 5.49,0.531 0.125,0.24 10 false 2 4.448,0.302 5.125,0.51 0.677,0.208 10 false 10*1, 15*2 4.448,1.094 5.135,1.365 0.688,0.271 10 false 18*1, 23*2 5.583,0.302 6.719,0.521 1.135,0.219 10 false LBE+*1, RBE+*2 5.583,1.333 6.604,1.531 1.021,0.198 10 false LBE-*1, RBE-*2 4.938,3.583 5.688,3.75 0.75,0.167 10 false *1: for LHD 4.938,3.917 5.688,4.083 0.75,0.167 10 false *2: for RHD 3.813,0.323 4.385,0.667 0.573,0.344 10 false LBE+*1, RBE+*2 3.844,1.094 4.385,1.427 0.542,0.333 10 false LBE-*1, RBE-*2

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK DTC OUTPUT (AIRBAG SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

b.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / SRS Airbag / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > SRS Airbag > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Left side Buckle SW LH buckle switch*1 Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined
-
Right side Buckle SW RH buckle switch*2 Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined
-

*1: for LHD

*2: for RHD


Body Electrical > SRS Airbag > Data List
Tester Display
Left side Buckle SW
Right side Buckle SW
50003 188 4,5
Result:
Result Proceed to
Unset or Set is displayed on the GTS according to the driver seat belt condition A
Unset or Set is not displayed correctly on the GTS according to the driver seat belt condition B
NG is displayed on the GTS C




A

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)

C

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK SEAT BELT WARNING LIGHT
4.CHECK SEAT BELT WARNING LIGHT
a.

Check the operation of the seat belt warning light.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION

OK:

The seat belt warning light operates normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY