Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0101004 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM C

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  B241A  Rear Height Control Sensor  


DESCRIPTION

The headlight leveling ECU assembly receives signals indicating the height of the vehicle from the rear height control sensor sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B241A Rear Height Control Sensor
·

Malfunction in rear height control sensor sub-assembly

·

Open or short in rear height control sensor sub-assembly circuit


·

Rear height control sensor sub-assembly

·

Harness or connector

·

Headlight leveling ECU assembly



WIRING DIAGRAM

E256783E12
0.802,1.958 3.479,2.219 2.677,0.26 10 false Rear Height Control Sensor Sub-assembly 4.208,1.938 6.99,2.365 2.781,0.427 10 false Headlight Leveling ECU Assembly 4.208,1.781 4.573,1.99 0.365,0.208 10 false A67 2.354,0.979 2.906,1.177 0.552,0.198 10 false SHRR 4.365,0.979 4.917,1.177 0.552,0.198 10 false SHRL 2.865,0.854 3.146,1.042 0.281,0.188 10 false 2 4.094,0.854 4.375,1.042 0.281,0.188 10 false 19 0.802,1.792 1.333,2.01 0.531,0.219 10 false O5

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight leveling ECU assembly has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

If any of the following are performed, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

-

Replacement of the rear height control sensor sub-assembly

-

Removal/installation of the rear height control sensor sub-assembly

-

Work that changes the vehicle height such as replacement of suspension components




PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC B241A is not output.



Result:
Proceed to
OK
NG



OK

NG

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the display on the GTS.

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rr Height Sens Signal Val Rear height control sensor signal value 0.00 to 5.00 V 0.50 to 4.50 V Value changes according to vehicle height
Body Electrical > HL AutoLeveling > Data List
Tester Display
Rr Height Sens Signal Val
50003 361 7
OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
a.

Disconnect the A67 headlight leveling ECU assembly connector.


b.

Disconnect the O5 rear height control sensor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-19 (SHRL) - O5-2 (SHRR) Always Below 1 Ω
A67-19 (SHRL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
a.

Remove the rear height control sensor sub-assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the rear height control sensor sub-assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY