Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0705  Transmission Range Sensor Circuit (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit (PRNDL Input) One of the following conditions A, B or C is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more:
(a) Any 2 or more of the following signals are on simultaneously:
·

P input signal

·

R input signal

·

D input signal


(b) Any 2 or more of the following signals are on simultaneously:
·

N input signal

·

R input signal

·

D input signal


(c) Any 2 or more of the following signals are on simultaneously:
·

NSW input signal

·

R input signal

·

D input signal


B. Any of the following conditions is met for 2 seconds or more in the S position:
·

NSW input signal is on

·

P input signal is on

·

N input signal is on

·

R input signal is on


C. All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more.
·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

Open or short in transmission control switch circuit

·

Transmission floor shift assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D, or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Park/Neutral position switch assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Move the shift lever to R and wait 2 seconds or more.

7.

Move the shift lever to N and wait 2 seconds or more.

8.

Move the shift lever to D and wait 2 seconds or more.

9.

Move the shift lever to S and wait 2 seconds or more.

10.

Move the shift lever to P and wait 2 seconds or more.

11.

Wait 1 minute or more.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P0705.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A300880E08
6.156,0.583 6.344,0.729 0.188,0.146 10 false D 6.156,1.125 6.344,1.271 0.188,0.146 10 false N 6.156,1.688 6.344,1.833 0.188,0.146 10 false R 6.167,2.24 6.354,2.385 0.188,0.146 10 false P 6.156,5.333 6.344,5.479 0.188,0.146 10 false S 6.146,2.802 6.625,2.958 0.479,0.156 10 false NSW 6.146,3.906 6.625,4.063 0.479,0.156 10 false STA 6.146,5.948 6.469,6.083 0.323,0.135 10 false E1 5.802,0.563 6.208,0.76 0.406,0.198 10 false C1 5.802,2.781 6.26,3.125 0.458,0.344 10 false C1 5.771,3.896 6.052,4.052 0.281,0.156 10 false A43 5.813,5.938 6.219,6.146 0.406,0.208 10 false C1 5.802,1.115 6.177,1.344 0.375,0.229 10 false C1 5.802,1.677 6.125,1.885 0.323,0.208 10 false C1 5.802,2.229 6.188,2.438 0.385,0.208 10 false C1 5.792,5.323 6.156,5.531 0.365,0.208 10 false A43 3.792,5.229 3.969,5.396 0.177,0.167 10 false S 3,5.229 3.271,5.396 0.271,0.167 10 false IG 5.813,0.375 6.188,0.604 0.375,0.229 10 false 69 5.813,0.927 6.021,1.083 0.208,0.156 10 false 71 5.823,1.49 6.042,1.646 0.219,0.156 10 false 68 5.813,2.052 6.031,2.208 0.219,0.156 10 false 70 5.823,2.594 6.042,2.75 0.219,0.156 10 false 65 5.844,3.708 6.063,3.865 0.219,0.156 10 false 9 5.833,5.146 6.052,5.302 0.219,0.156 10 false 37 5.823,5.76 6.146,6.021 0.323,0.26 10 false 49 6.365,7.01 6.719,7.188 0.354,0.177 10 false ECM 2.583,5.75 4.354,5.917 1.771,0.167 10 false Transmission Control Switch 3.094,4.365 4.406,4.563 1.313,0.198 10 false to ST Relay 2.813,5.229 2.969,5.406 0.156,0.177 10 false 3 3.99,5.229 4.146,5.427 0.156,0.198 10 false 7 0.302,5.323 1.656,5.49 1.354,0.167 10 false from IG1 NO. 3 Fuse 0.927,3.375 3.375,3.542 2.448,0.167 10 false Park/Neutral Position Switch Assembly 0.938,3.229 1.302,3.521 0.365,0.292 10 false C14 0.052,1.396 1.115,1.563 1.063,0.167 10 false from BKUP Fuse 2.292,0.469 2.615,0.615 0.323,0.146 10 false DL 2.292,1.031 2.615,1.177 0.323,0.146 10 false NL 2.292,1.573 2.615,1.719 0.323,0.146 10 false RL 2.292,2.135 2.615,2.281 0.323,0.146 10 false PL 2.344,2.677 2.667,2.823 0.323,0.146 10 false B 1.604,2.688 1.875,2.854 0.271,0.167 10 false L 1.583,1.302 1.865,1.469 0.281,0.167 10 false RB 2.563,0.479 2.75,0.635 0.188,0.156 10 false 7 2.563,1.031 2.698,1.198 0.135,0.167 10 false 8 2.563,1.583 2.74,1.75 0.177,0.167 10 false 2 2.573,2.146 2.688,2.354 0.115,0.208 10 false 3 2.563,2.688 2.75,2.865 0.188,0.177 10 false 4 1.406,1.302 1.552,1.469 0.146,0.167 10 false 1 1.417,2.688 1.594,2.854 0.177,0.167 10 false 9 2.573,5.583 2.906,5.729 0.333,0.146 10 false F46

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List / All Data / Shift SW Status (P Range), Shift SW Status (R Range), Shift SW Status (N Range), Shift SW Status (D Range) and Shift Mode Selection SW.

Powertrain > Engine > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Sports Mode Selection SW
Shift SW Status (D Range)
50003 234 125,126,127,133,128

g.

Read the values displayed on the GTS.

GTS Display Measurement Item/Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Shift SW Status (P Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Shift SW Status (N Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Shift SW Status (D Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Sports Mode Selection SW Sport mode select switch status:
ON or OFF
·

ON: Shift lever in S

·

OFF: Shift lever not in S


-



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL AND SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW Signal and Shift SW Status (R, P, N and D Range).

Powertrain > Engine > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 234 147,125,126,127,128

e.

Read the values displayed on the GTS.

OK:
GTS Display Shift Lever Position Specified Condition
Neutral Position SW Signal P or N ON
Except P or N OFF
Shift SW Status (R Range) R ON
Except R OFF
Shift SW Status (P Range) P ON
Except P OFF
Shift SW Status (N Range) N ON
Except N OFF
Shift SW Status (D Range) D or S ON
Except D or S OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)

NG

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Sports Mode Selection SW.

Powertrain > Engine > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

e.

Read the values displayed on the GTS.

OK:
GTS Display Shift Lever Position Specified Condition
Sports Mode Selection SW S ON
Except S OFF



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

4.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL SWITCH)
A255690C81
0.531,1.052 0.948,1.313 0.417,0.26 1.875,1.385 1.771,1.917 false 0.177,0.146 0.344,0.323 0.167,0.177 10 false *a 0.625,1.094 1.073,1.385 0.448,0.292 10 false A43 1.698,1.917 1.813,2.063 0.115,0.146 10 false S
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Disconnect the TCM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Shift Lever Position Condition Specified Condition
A43-37 (S) - Body ground S Ignition switch ON 11 to 14 V
Not in S Ignition switch ON 0 to 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
A194118C07
0.26,2.26 0.698,2.521 0.438,0.26 1.594,2.396 1.104,1.604 true 0.229,0.135 0.438,0.302 0.208,0.167 10 false *a 0.365,2.313 0.667,2.469 0.302,0.156 10 false C14 0.854,1.49 1.073,1.646 0.219,0.156 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


a.

Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C14-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Disconnect the TCM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-7 (DL) - C1-69 (D) Always Below 1 Ω
C14-8 (NL) - C1-71 (N) Always Below 1 Ω
C14-2 (RL) - C1-68 (R) Always Below 1 Ω
C14-3 (PL) - C1-70 (P) Always Below 1 Ω
C14-4 (B) - C1-65 (NSW) Always Below 1 Ω
C14-7 (DL) or C1-69 (D) - Body ground Always 10 kΩ or higher
C14-8 (NL) or C1-71 (N) - Body ground Always 10 kΩ or higher
C14-2 (RL) or C1-68 (R) - Body ground Always 10 kΩ or higher
C14-3 (PL) or C1-70 (P) - Body ground Always 10 kΩ or higher
C14-4 (B) or C1-65 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR