Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  U0101  Lost Communication with TCM  


DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communication with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine speed, required engine torque, warning indicators in the combination meter assembly, DTCs and other data. The ECM sends signals to the TCM concerning engine speed, opening angle of the throttle valve, temperature of intake air, temperature of engine coolant, engine torque and other data. If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN communication system, illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0101 Lost Communication with TCM All of the following conditions are met for 1.25 seconds (1 trip detection logic):
1.

Ignition switch ON

2.

Battery voltage 10.5 V or higher

3.

No communication between ECM and TCM


·

ECM to TCM circuit

·

TCM

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: U0101.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A315969E01
0.833,2.896 1.167,3.063 0.333,0.167 10 false TCM 0.583,2.896 0.833,3.063 0.25,0.167 10 false C3 1.052,2.438 1.333,2.604 0.281,0.167 10 false E1 0.875,2.063 1.292,2.229 0.417,0.167 10 false BATT 1.031,1.667 1.313,1.833 0.281,0.167 10 false +B 0.854,1.313 1.302,1.479 0.448,0.167 10 false CAN+ 0.885,0.885 1.333,1.052 0.448,0.167 10 false CAN- 1.354,0.75 1.5,0.917 0.146,0.167 10 false 7 1.354,1.177 1.5,1.344 0.146,0.167 10 false 6 1.354,1.573 1.583,1.74 0.229,0.167 10 false 18 1.792,1.823 2.458,1.99 0.667,0.167 10 false EFI NO. 2 1.354,1.948 1.5,2.115 0.146,0.167 10 false 1 1.354,2.333 1.5,2.5 0.146,0.167 10 false 8 1.792,2.208 2.458,2.375 0.667,0.167 10 false EFI NO. 1 2.563,2.198 3.229,2.365 0.667,0.167 10 false EFI-MAIN 3.177,1.667 4.51,1.833 1.333,0.167 10 false from EFI MAIN Relay 3.74,2.052 4.573,2.219 0.833,0.167 10 false from Battery 6.083,2.896 6.333,3.063 0.25,0.167 10 false C1 6.333,2.896 6.75,3.063 0.417,0.167 10 false ECM 5.771,0.729 5.938,0.896 0.167,0.167 10 false 1 5.729,1.177 5.917,1.344 0.188,0.167 10 false 31 6.01,0.885 6.427,1.052 0.417,0.167 10 false CAN- 6.01,1.323 6.427,1.49 0.417,0.167 10 false CAN+ 2.885,3.156 4.698,3.354 1.813,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Read the DTCs.

Result:
Result Proceed to
DTC U0101 is output A
DTC U0101 and other DTCs are output B


HINT:

If any DTCs other than U0101 are output, troubleshoot those DTCs first.




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)

B

GO TO DTC CHART

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)
A194125C02
0.198,1.365 0.615,1.604 0.417,0.24 1.531,2.365 1.219,1.302 false 1.49,3.135 1.188,2.667 false 1.094,2.479 0.823,3.125 false 0.25,0.188 0.927,0.677 0.677,0.49 10 false *a 0.313,1.396 1.042,1.792 0.729,0.396 10 false C3 0.958,1.115 1.635,1.49 0.677,0.375 10 false BATT 1.448,3.135 2,3.427 0.552,0.292 10 false +B 0.656,3.156 1.01,3.396 0.354,0.24 10 false E1
*a Front view of wire harness connector
(to TCM)


a.

Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C3-1 (BATT) - C3-8 (E1) Always 11 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C3-18 (+B) - C3-8 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-6 (CAN+) - C1-31 (CAN+) Always Below 1 Ω
C3-7 (CAN-) - C1-1 (CAN-) Always Below 1 Ω
C3-6 (CAN+) or C1-31 (CAN+) - Body ground Always 10 kΩ or higher
C3-7 (CAN-) or C1-1 (CAN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTCs are not output A
DTC U0101 is output B




A

END

B