Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A280176E17
0.948,3.438 2.719,3.698 1.771,0.26 10 false : CAN Communication Line 5.615,2.146 6,2.396 0.385,0.25 10 false ECM 0.75,2.292 2.615,2.594 1.865,0.302 10 false Combination Meter Assembly 5.281,2.146 5.698,2.333 0.417,0.188 10 false A43 0.74,2.125 1.042,2.323 0.302,0.198 10 false F22 2.042,1.604 2.417,1.76 0.375,0.156 10 false CANL 4.771,1.604 5.146,1.76 0.375,0.156 10 false CANL 2.042,0.885 2.479,1.052 0.438,0.167 10 false CANH 4.76,0.906 5.198,1.083 0.438,0.177 10 false CANH 4.49,0.719 4.688,0.875 0.198,0.156 10 false 13 4.49,1.438 4.677,1.583 0.188,0.146 10 false 26 2.521,0.74 2.719,0.896 0.198,0.156 10 false 17 2.531,1.438 2.729,1.594 0.198,0.156 10 false 16

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Result Condition Proceed to
MIL ON→MIL OFF Ignition switch ON → engine is started A
MIL does not illuminate B
MIL remains ON C




A

B

C

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

3.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT

3.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY