Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A256646E03
1.333,0.823 2.646,1.115 1.313,0.292 10 from EFI NO. 1 Fuse 1.333,1.177 2.74,1.531 1.406,0.354 10 from EFI NO. 2 Fuse 0.135,1.969 2.625,2.469 2.49,0.5 10 to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.635,3.01 2.5,0.365 10 to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 ECM 2.885,0.677 3.563,1 0.677,0.323 10 BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 VC 4.396,0.875 6.188,1.229 1.792,0.354 10 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 R

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A315635E01
0.49,1.292 1.917,1.792 1.427,0.5 10 false VVT Sensor (for Intake Camshaft of Bank 1) 0.49,1.104 0.885,1.344 0.396,0.24 10 false C35 0.51,2.604 0.906,2.844 0.396,0.24 10 false C36 0.521,2.792 1.948,3.292 1.427,0.5 10 false VVT Sensor (for Intake Camshaft of Bank 2) 0.531,4.063 0.927,4.302 0.396,0.24 10 false C54 0.521,4.25 2.094,4.75 1.573,0.5 10 false VVT Sensor (for Exhaust Camshaft of Bank 1) 0.542,5.531 0.938,5.771 0.396,0.24 10 false C53 0.531,5.708 2.104,6.208 1.573,0.5 10 false VVT Sensor (for Exhaust Camshaft of Bank 2) 2.052,1.135 2.667,1.333 0.615,0.198 10 false VVR+ 2.063,1.49 2.677,1.688 0.615,0.198 10 false VVR- 2.208,1.875 2.823,2.073 0.615,0.198 10 false VC 2.063,2.615 2.677,2.813 0.615,0.198 10 false VVL+ 2.094,2.969 2.708,3.167 0.615,0.198 10 false VVL- 2.219,3.344 2.833,3.542 0.615,0.198 10 false VC 2.167,4.083 2.781,4.281 0.615,0.198 10 false EX+ 2.177,4.438 2.792,4.635 0.615,0.198 10 false EX- 2.135,4.792 2.75,4.99 0.615,0.198 10 false VC2 2.146,5.552 2.76,5.75 0.615,0.198 10 false EX+ 2.177,5.896 2.792,6.094 0.615,0.198 10 false EX- 2.125,6.281 2.74,6.479 0.615,0.198 10 false VC2 2.542,1.031 3.156,1.229 0.615,0.198 10 false 1 2.542,2.5 3.156,2.698 0.615,0.198 10 false 1 2.542,3.958 3.156,4.156 0.615,0.198 10 false 1 2.521,5.427 3.135,5.625 0.615,0.198 10 false 1 2.552,1.385 3.167,1.583 0.615,0.198 10 false 2 2.552,2.854 3.167,3.052 0.615,0.198 10 false 2 2.542,4.313 3.156,4.51 0.615,0.198 10 false 2 2.531,5.792 3.146,5.99 0.615,0.198 10 false 2 2.552,1.75 3.167,1.948 0.615,0.198 10 false 3 2.552,3.219 3.167,3.417 0.615,0.198 10 false 3 2.552,4.688 3.167,4.885 0.615,0.198 10 false 3 2.542,6.167 3.156,6.365 0.615,0.198 10 false 3 5.302,1.156 5.917,1.354 0.615,0.198 10 false VV1+ 5.302,1.396 5.917,1.594 0.615,0.198 10 false VV1- 5.302,1.76 5.917,1.958 0.615,0.198 10 false VCV1 5.302,2.625 5.917,2.823 0.615,0.198 10 false VV2+ 5.292,4.073 5.906,4.271 0.615,0.198 10 false EV1+ 5.292,5.552 5.906,5.75 0.615,0.198 10 false EV2+ 5.688,7.531 6.302,7.729 0.615,0.198 10 false ECM 4.969,1.146 5.583,1.344 0.615,0.198 10 false C1 4.969,1.51 5.583,1.708 0.615,0.198 10 false C1 4.969,1.875 5.583,2.073 0.615,0.198 10 false C1 4.969,2.604 5.583,2.802 0.615,0.198 10 false C1 4.969,4.073 5.583,4.271 0.615,0.198 10 false C1 4.969,5.552 5.583,5.75 0.615,0.198 10 false C1 4.99,0.958 5.604,1.156 0.615,0.198 10 false 81 4.938,1.333 5.552,1.531 0.615,0.198 10 false 110 4.948,1.688 5.563,1.885 0.615,0.198 10 false 111 5,2.427 5.615,2.625 0.615,0.198 10 false 78 4.979,3.885 5.594,4.083 0.615,0.198 10 false 79 4.99,5.365 5.604,5.563 0.615,0.198 10 false 80 6.021,0.969 6.292,1.156 0.271,0.188 10 false 5 V

A315020E01
0.552,1.01 1.01,1.208 0.458,0.198 10 false C41 0.552,1.208 1.656,1.896 1.104,0.688 10 false Throttle Body with Motor Assembly 0.552,2.646 1.01,2.844 0.458,0.198 10 false A53 0.552,2.823 1.688,3.333 1.135,0.51 10 false Accelerator Pedal Sensor Assembly 1.99,1.063 2.448,1.26 0.458,0.198 10 false E2 1.823,1.427 2.281,1.625 0.458,0.198 10 false VTA2 1.979,1.792 2.438,1.99 0.458,0.198 10 false VC 1.906,2.156 2.365,2.354 0.458,0.198 10 false VTA 2.302,0.938 2.76,1.135 0.458,0.198 10 false 3 2.302,1.302 2.76,1.5 0.458,0.198 10 false 4 2.302,1.677 2.76,1.875 0.458,0.198 10 false 5 2.302,2.042 2.76,2.24 0.458,0.198 10 false 6 1.813,2.656 2.271,2.854 0.458,0.198 10 false VCP2 1.813,3.021 2.271,3.219 0.458,0.198 10 false EPA2 1.813,3.375 2.271,3.573 0.458,0.198 10 false VPA2 1.792,3.74 2.25,3.938 0.458,0.198 10 false VCPA 1.875,4.094 2.333,4.292 0.458,0.198 10 false EPA 1.885,4.458 2.344,4.656 0.458,0.198 10 false VPA 2.292,2.531 2.75,2.729 0.458,0.198 10 false 1 2.302,2.885 2.76,3.083 0.458,0.198 10 false 2 2.302,3.25 2.76,3.448 0.458,0.198 10 false 3 2.302,3.615 2.76,3.813 0.458,0.198 10 false 4 2.302,3.979 2.76,4.177 0.458,0.198 10 false 5 2.302,4.354 2.76,4.552 0.458,0.198 10 false 6 5.01,1.063 5.469,1.26 0.458,0.198 10 false C1 5.021,1.427 5.479,1.625 0.458,0.198 10 false C1 5.021,1.792 5.479,1.99 0.458,0.198 10 false C1 5.021,2.146 5.479,2.344 0.458,0.198 10 false C1 4.979,2.656 5.438,2.854 0.458,0.198 10 false A43 4.979,3.021 5.438,3.219 0.458,0.198 10 false A43 4.979,3.375 5.438,3.573 0.458,0.198 10 false A43 4.979,3.74 5.438,3.938 0.458,0.198 10 false A43 4.979,4.104 5.438,4.302 0.458,0.198 10 false A43 4.979,4.458 5.438,4.656 0.458,0.198 10 false A43 4.979,0.875 5.438,1.073 0.458,0.198 10 false 125 4.99,1.24 5.448,1.438 0.458,0.198 10 false 127 4.979,1.615 5.438,1.813 0.458,0.198 10 false 126 4.99,1.969 5.448,2.167 0.458,0.198 10 false 128 5.021,2.469 5.479,2.667 0.458,0.198 10 false 59 5.031,2.833 5.49,3.031 0.458,0.198 10 false 58 5.021,3.198 5.479,3.396 0.458,0.198 10 false 57 5.042,3.563 5.5,3.76 0.458,0.198 10 false 56 5.031,3.927 5.49,4.125 0.458,0.198 10 false 55 5.042,4.281 5.5,4.479 0.458,0.198 10 false 54 5.333,0.969 5.792,1.167 0.458,0.198 10 false ETA 5.333,1.417 5.792,1.615 0.458,0.198 10 false VTA2 5.333,1.688 5.792,1.885 0.458,0.198 10 false VCTA 5.333,2.146 5.792,2.344 0.458,0.198 10 false VTA1 5.333,2.531 5.792,2.729 0.458,0.198 10 false VCP2 5.344,2.906 5.802,3.104 0.458,0.198 10 false EPA2 5.333,3.365 5.792,3.563 0.458,0.198 10 false VPA2 5.323,3.635 5.781,3.833 0.458,0.198 10 false VCPA 5.323,3.99 5.781,4.188 0.458,0.198 10 false EPA 5.344,4.438 5.802,4.635 0.458,0.198 10 false VPA 5.771,5.167 6.229,5.365 0.458,0.198 10 false ECM

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



A

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1)

6.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2)

7.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

8.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1)

8.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

9.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2)

9.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


d.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


e.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


f.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


g.

Disconnect the ECM connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-5 (VC) or C1-126 (VCTA) - Body ground Always 10 kΩ or higher
A53-4 (VCPA) or A43-56 (VCPA) - Body ground Always 10 kΩ or higher
A53-1 (VCP2) or A43-59 (VCP2) - Body ground Always 10 kΩ or higher
C1-111 (VCV1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR