Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM3160E _59 Vehicle Exterior _019720 MIRROR (EXT) _0101072 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirror Surface Position is not Memorized  


DESCRIPTION

If any of the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. On receiving the seat memory switch signal, the main body ECU (multiplex network body ECU) sends the memory request signal to each outer mirror control ECU assembly via CAN communication. When receiving this signal, each outer mirror control ECU assembly stores the mirror surface position based on information from the mirror position sensor, which is built into the outer rear view mirror assembly.

WIRING DIAGRAM

for LHD


E267862E07
0.333,5.469 1.521,6.031 1.188,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 0.583,8.052 2.333,8.281 1.75,0.229 10 false : CAN Communication Line 2.625,5.271 4.177,5.688 1.552,0.417 10 false Outer Mirror Control ECU Assembly (Driver Door) 4.979,8.125 7.052,8.49 2.073,0.365 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 5.26,2.25 6.708,2.708 1.448,0.458 10 false Outer Rear View Mirror Assembly (Driver Door) 2.5,8.104 4.698,8.51 2.198,0.406 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 4.073,3.5 4.458,3.771 0.385,0.271 10 false I2 4.073,4.458 4.479,4.677 0.406,0.219 10 false I2 4.104,4.229 4.323,4.479 0.219,0.25 10 false 1 4.073,3.979 4.479,4.208 0.406,0.229 10 false I2 3.646,6.313 3.938,6.583 0.292,0.271 10 false VC 3.667,7.76 4.042,7.958 0.375,0.198 10 false E1 3.458,6.813 3.875,7.031 0.417,0.219 10 false VSSR 3.448,7.292 3.927,7.5 0.479,0.208 10 false HSSR 3.646,0.333 3.969,0.563 0.323,0.229 10 false VC 3.677,1.75 4.031,1.99 0.354,0.24 10 false E1 3.469,0.802 3.906,1.063 0.438,0.26 10 false VSRL 3.469,1.281 3.927,1.5 0.458,0.219 10 false HSRL 3.635,3.521 3.917,3.771 0.281,0.25 10 false M1 3.594,4.479 3.927,4.708 0.333,0.229 10 false MM 3.635,4 3.938,4.208 0.302,0.208 10 false M2 5.51,3.531 5.823,3.854 0.313,0.323 10 false 1 5.51,4.458 6,4.677 0.49,0.219 10 false MMRY 6.365,4.49 6.531,4.781 0.167,0.292 10 false E 5.51,3.99 5.844,4.229 0.333,0.24 10 false 2 5.292,3.885 5.469,4.094 0.177,0.208 10 false 3 6.583,4.354 6.781,4.563 0.198,0.208 10 false 2 5.302,4.354 5.469,4.563 0.167,0.208 10 false 8 4.094,0.083 4.271,0.271 0.177,0.188 10 false 5 4.021,0.302 4.365,0.542 0.344,0.24 10 false z10 4.021,0.771 4.333,1.052 0.313,0.281 10 false z10 4.021,1.26 4.375,1.458 0.354,0.198 10 false z10 4.021,1.719 4.365,1.927 0.344,0.208 10 false z10 4.052,1.51 4.333,1.677 0.281,0.167 10 false 14 4.052,7.75 4.354,7.979 0.302,0.229 10 false z9 4.052,7.26 4.417,7.458 0.365,0.198 10 false z9 4.052,6.781 4.333,7.083 0.281,0.302 10 false z9 4.042,6.281 4.365,6.5 0.323,0.219 10 false z9 5.365,5.042 6.729,5.292 1.365,0.25 10 false Seat Memory Switch 5.365,4.875 5.76,5.115 0.396,0.24 10 false I11 4.094,0.542 4.292,0.771 0.198,0.229 10 false 6 4.052,1.042 4.313,1.25 0.26,0.208 10 false 13 4.115,3.292 4.323,3.521 0.208,0.229 10 false 2 4.115,3.76 4.313,3.948 0.198,0.188 10 false 3 4.094,6.083 4.292,6.313 0.198,0.229 10 false 5 4.052,7.542 4.302,7.75 0.25,0.208 10 false 14 4.094,6.563 4.292,6.813 0.198,0.25 10 false 6 4.063,7.042 4.313,7.302 0.25,0.26 10 false 13 5.292,3.396 5.448,3.615 0.156,0.219 10 false 4


for RHD


E267862E08
0.333,5.51 1.531,5.99 1.198,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 0.573,8.083 2.281,8.219 1.708,0.135 10 false : CAN Communication Line 2.625,5.271 4.208,5.583 1.583,0.313 10 false Outer Mirror Control ECU Assembly (Driver Door) 4.979,8.125 7.073,8.427 2.094,0.302 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 5.26,2.26 6.708,2.74 1.448,0.479 10 false Outer Rear View Mirror Assembly (Driver Door) 2.5,8.104 4.74,8.406 2.24,0.302 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 4.052,3.51 4.427,3.781 0.375,0.271 10 false H2 4.042,4.469 4.406,4.708 0.365,0.24 10 false H2 4.094,4.24 4.26,4.438 0.167,0.198 10 false 1 4.052,3.979 4.427,4.229 0.375,0.25 10 false H2 3.635,6.313 3.979,6.521 0.344,0.208 10 false VC 3.583,7.76 3.938,7.958 0.354,0.198 10 false E1 3.448,6.813 3.854,7.063 0.406,0.25 10 false VSRL 3.448,7.292 3.875,7.51 0.427,0.219 10 false HSRL 3.656,0.333 4,0.552 0.344,0.219 10 false VC 3.667,1.76 3.969,1.979 0.302,0.219 10 false E1 3.458,0.802 3.885,1.052 0.427,0.25 10 false VSSR 3.458,1.292 3.927,1.51 0.469,0.219 10 false HSSR 3.646,3.531 3.906,3.76 0.26,0.229 10 false M1 3.604,4.479 3.927,4.656 0.323,0.177 10 false MM 3.646,4.01 3.906,4.177 0.26,0.167 10 false M2 5.5,3.531 5.823,3.771 0.323,0.24 10 false M1 5.51,4.448 6,4.656 0.49,0.208 10 false MRY 6.375,4.479 6.5,4.708 0.125,0.229 10 false E 5.51,3.99 5.833,4.271 0.323,0.281 10 false M2 5.302,3.896 5.458,4.104 0.156,0.208 10 false 3 6.583,4.365 6.75,4.583 0.167,0.219 10 false 2 5.302,4.365 5.531,4.573 0.229,0.208 10 false 8 4.104,0.104 4.271,0.26 0.167,0.156 10 false 5 4.052,0.302 4.385,0.49 0.333,0.188 10 false z9 4.052,0.771 4.396,0.958 0.344,0.188 10 false z9 4.042,1.26 4.396,1.552 0.354,0.292 10 false z9 4.063,1.708 4.417,1.958 0.354,0.25 10 false z9 4.052,1.521 4.24,1.698 0.188,0.177 10 false 14 4.021,7.75 4.354,7.969 0.333,0.219 10 false z10 4.021,7.25 4.385,7.49 0.365,0.24 10 false z10 4.021,6.781 4.427,6.99 0.406,0.208 10 false z10 4.021,6.281 4.385,6.469 0.365,0.188 10 false z10 5.365,5.042 6.74,5.302 1.375,0.26 10 false Seat Memory Switch 5.365,4.875 5.719,5.073 0.354,0.198 10 false H12 4.104,0.563 4.25,0.76 0.146,0.198 10 false 6 4.063,1.063 4.24,1.24 0.177,0.177 10 false 13 4.115,3.292 4.313,3.49 0.198,0.198 10 false 2 4.104,3.771 4.344,3.948 0.24,0.177 10 false 3 4.104,6.083 4.354,6.281 0.25,0.198 10 false 5 4.063,7.531 4.302,7.708 0.24,0.177 10 false 14 4.104,6.573 4.292,6.75 0.188,0.177 10 false 6 4.063,7.063 4.302,7.281 0.24,0.219 10 false 13 5.292,3.396 5.469,3.583 0.177,0.188 10 false 4


CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The mirror surface position will not be memorized if the ignition switch is not ON.

·

The mirror surface position will not be stored if the seat memory SET switch and 2 or more seat memory switches are pressed simultaneously.

·

If the operation fails, the mirror surface position will not be memorized until the seat memory SET switch is released and the operation is attempted again.

·

The mirror surface position will not be memorized when the mirror is operated manually.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




HINT:

Each outer rear view mirror assembly has a built-in mirror vertical position sensor and mirror horizontal position sensor.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Mirror L*1 or Mirror R*2 / Data List.

*1: for LHD

*2: for RHD



e.

Read the Data List according to the display on the GTS.

i.

for LHD

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
-
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
-
Seat Memory Switch3 Seat memory switch M3 switch signal* OFF or ON OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
Not applicable
Seat Memory Set SW Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
-

*: Although the item is displayed on the GTS, it is not applicable to this vehicle.


Body Electrical > Mirror L > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Switch3
Seat Memory Set SW
50003 225 1,2,3,4

ii.

for RHD

Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
-
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
-
Seat Memory Switch3 Seat memory switch M3 switch signal* OFF or ON OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
Not applicable
Seat Memory Set SW Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
-

*: Although the item is displayed on the GTS, it is not applicable to this vehicle.


Body Electrical > Mirror R > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Switch3
Seat Memory Set SW
50003 224 1,2,3,4


OK:

On the GTS screen, ON or OFF is displayed accordingly.


Result:
Proceed to
OK
NG



OK

2.CHECK SEAT MEMORY SWITCH FUNCTION

NG

8.INSPECT SEAT MEMORY SWITCH
2.CHECK SEAT MEMORY SWITCH FUNCTION
a.

When any seat memory switch (M1 or M2) is pressed, check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

The driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

3.CHECK MEMORY AND REACTIVATION FUNCTION

NG

GO TO FRONT POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

3.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Result Proceed to
Memory and reactivation functions on both mirrors are not normal A
Memory and reactivation functions on driver door mirror are not normal B
Memory and reactivation functions on front passenger door mirror are not normal C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

4.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

C

6.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)
4.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)
a.

Temporarily replace the outer rear view mirror assembly (driver door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK MEMORY AND REACTIVATION FUNCTION
5.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

6.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)
a.

Temporarily replace the outer rear view mirror assembly (front passenger door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK MEMORY AND REACTIVATION FUNCTION
7.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

8.INSPECT SEAT MEMORY SWITCH
a.

Remove the seat memory switch (driver door).

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Inspect the seat memory switch (driver door).

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - BODY GROUND)

NG

REPLACE SEAT MEMORY SWITCH

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - BODY GROUND)
a.

Disconnect the I2*1 or H2*2 outer mirror control ECU assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the I11 seat memory switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I2-1 (MM) - I11-8 (MMRY) Always Below 1 Ω
I2-2 (M1) - I11-4 (1) Always Below 1 Ω
I2-3 (M2) - I11-3 (2) Always Below 1 Ω
I11-2 (E) - Body ground Always Below 1 Ω
I2-1 (MM) or I11-8 (MMRY) - Body ground Always 10 kΩ or higher
I2-2 (M1) or I11-4 (1) - Body ground Always 10 kΩ or higher
I2-3 (M2) or I11-3 (2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H2-1 (MM) - H12-8 (MRY) Always Below 1 Ω
H2-2 (M1) - H12-4 (M1) Always Below 1 Ω
H2-3 (M2) - H12-3 (M2) Always Below 1 Ω
H12-2 (E) - Body ground Always Below 1 Ω
H2-1 (MM) or H12-8 (MRY) - Body ground Always 10 kΩ or higher
H2-2 (M1) or H12-4 (M1) - Body ground Always 10 kΩ or higher
H2-3 (M2) or H12-3 (M2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR