Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM3160E _55 Steering _019698 STEERING COLUMN _0101108 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.INSTALL STEERING POST ASSEMBLY

a.

Install the steering post assembly with the bolt and 2 nuts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Make sure that the wire harness is not interfering with the steering post assembly.



b.

Connect the 2 connectors.


c.

Engage the 2 clamps.


d.

Install the ground wire with the bolt.

Torque:
8.35 N*m (85 kgf*cm, 74 in.*lbf)


e.

Connect each connector and engage each wire harness clamp to the steering post assembly.


Hide 47110 3.INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

Hide 87201L 4.INSTALL NO. 4 AIR DUCT SUB-ASSEMBLY (for LHD)

a.

Engage the 2 claws and guide to install the No. 4 air duct sub-assembly.


b.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87201F 5.INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY (for RHD)

a.

Engage the 2 claws and guide to install the No. 3 air duct sub-assembly.


Hide 45220 6.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C291595C01
1.615,0.948 2,1.031 2,1.031 1.646,0.906 true 2.01,0.938 2.25,1.135 0.24,0.198 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and steering link assembly.


b.

Connect the steering intermediate shaft assembly to the steering link assembly.


c.

Install a new bolt.

Torque:
35.3 N*m (360 kgf*cm, 26 ft.*lbf)


d.

Install the steering intermediate shaft assembly to the steering column hole shield.


e.
C291594

Tighten the bolt.


Hide 73900 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 8.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.


b.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 9.INSTALL UPPER STEERING COLUMN COVER

a.

Engage the 2 claws to install the upper steering column cover.


b.

Engage the 6 clips to the upper steering column cover.


Hide 45287 10.INSTALL LOWER STEERING COLUMN COVER

a.

Engage the 3 claws to install the lower steering column cover.


b.

Install the 2 screws.


Hide 11.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 12.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 45100 13.INSTALL STEERING WHEEL ASSEMBLY

Hide 14.CHECK STEERING WHEEL CENTER POINT

Hide 45130 15.INSTALL HORN BUTTON ASSEMBLY

Hide 16.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 17.ADJUST PARKING ASSIST MONITOR SYSTEM (w/ Parking Assist Monitor System)