Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0109987 KNEE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 73900 1.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B355773C01
1.583,1.083 1.063,1.083 true 1.469,0.604 1.323,0.333 1.323,0.333 1.083,0.333 true 2.448,2.563 2.229,2.979 2.229,2.979 2.031,2.979 true 0.885,0.979 1.083,1.198 0.198,0.219 10 true *a 1.885,2.875 2.073,3.063 0.188,0.188 10 false *b 0.917,0.229 1.146,0.448 0.229,0.219 10 true *1
*1 DLC3
*a Airbag Connector
*b Airbag Connector Lock


Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



d.

Push in the airbag connector lock to install the airbag connector.


e.

Engage the 2 claws and clamp to connect the DLC3.


f.

Engage the 2 clamps.


g.

Engage the 3 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.


h.

Install the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.



Hide 73900 2.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B356690C01
1.302,1.469 1.958,1.469 false 2.427,2.708 2.167,3.01 2.167,3.01 1.948,3.01 true 1.26,0.604 1.719,0.229 1.719,0.229 1.979,0.229 true 2,1.385 2.313,1.542 0.313,0.156 10 false *a 1.802,2.927 2.115,3.083 0.313,0.156 10 false *b 2.01,0.146 2.323,0.302 0.313,0.156 10 false *1
*1 DLC3
*a Airbag Connector
*b Airbag Connector Lock


Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



d.

Push in the airbag connector lock to install the airbag connector.


e.

Engage the 2 claws and clamp to connect the DLC3.


f.

Engage the 2 clamps.


g.

Engage the 3 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.


h.

Install the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.



Hide 55045 3.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 53601 4.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55606 5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55436A 6.INSTALL INSTRUMENT PANEL FINISH PANEL END

Hide 7.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 62112A 8.INSTALL COWL SIDE TRIM SUB-ASSEMBLY

Hide 67914 9.INSTALL FRONT DOOR SCUFF PLATE

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION