Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103403 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights.

WIRING DIAGRAM

E288112E04
1.948,4.052 2.104,4.25 0.156,0.198 10 false 1 5.5,4.729 5.823,4.969 0.323,0.24 10 false MB 2.448,1.708 2.698,1.927 0.25,0.219 10 false 14 1.948,5.229 2.104,5.427 0.156,0.198 10 false 1 4.031,0.823 4.208,1.031 0.177,0.208 10 false 7 2.49,1.229 2.646,1.427 0.156,0.198 10 false 4 2.5,2.177 2.656,2.375 0.156,0.198 10 false 5 4.031,1.969 4.208,2.177 0.177,0.208 10 false 6 6,0.885 6.177,1.094 0.177,0.208 10 false 7 4.615,0.844 4.792,1.052 0.177,0.208 10 false 25 2.479,0.76 2.635,0.958 0.156,0.198 10 false 1 3.25,5.25 3.406,5.448 0.156,0.198 10 false 2 2.479,0.281 2.635,0.479 0.156,0.198 10 false 1 3.25,4.063 3.406,4.26 0.156,0.198 10 false 2 2.438,0.979 2.698,1.208 0.26,0.229 10 false 1A 4.604,1.042 4.865,1.271 0.26,0.229 10 false 4F 3.969,1.031 4.229,1.26 0.26,0.229 10 false 1D 3.969,2.167 4.229,2.396 0.26,0.229 10 false 1E 2.438,1.448 2.698,1.677 0.26,0.229 10 false 1E 2.448,0.49 2.708,0.719 0.26,0.229 10 false 1B 2.448,1.906 2.708,2.135 0.26,0.229 10 false 1D 2.438,2.354 2.698,2.583 0.26,0.229 10 false 1G 0.396,0.458 1.365,0.677 0.969,0.219 10 false from Battery 0.156,1.417 1.26,1.667 1.104,0.25 10 false from TAIL Relay 1.781,1.125 2.156,1.313 0.375,0.188 10 false ALT 1.781,1.583 2.156,1.771 0.375,0.188 10 false TAIL 2.792,0.49 3.229,0.688 0.438,0.198 10 false BATT 2.802,0.969 3.24,1.167 0.438,0.198 10 false ALT 2.802,1.448 3.24,1.646 0.438,0.198 10 false TAIL 2.792,1.917 3.229,2.115 0.438,0.198 10 false GND1 2.792,2.354 3.229,2.552 0.438,0.198 10 false GND2 3.406,2.177 4.021,2.396 0.615,0.219 10 false FOGR 3.406,1.042 3.948,1.292 0.542,0.25 10 false FOGS 6.198,1.042 6.698,1.271 0.5,0.229 10 false FFGO 2.677,3.063 3.917,3.458 1.24,0.396 10 false Semiconductor Pwr Integration ECU 1.917,5.708 2.375,5.906 0.458,0.198 10 false A23 1.885,4.51 2.344,4.708 0.458,0.198 10 false A15 1.885,4.667 3.448,4.896 1.563,0.229 10 false Fog Light Assembly LH 1.917,5.865 3.479,6.094 1.563,0.229 10 false Fog Light Assembly RH 4.479,1.49 6.083,1.917 1.604,0.427 10 false Instrument Panel Junction Block Assembly 5.5,4.896 7.125,5.365 1.625,0.469 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses and bulbs for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relay operates.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Fog Light Relay Front fog light relay ON/OFF Light control switch in tail position
Body Electrical > Main Body > Active Test
Tester Display
Front Fog Light Relay
50004 123 16
OK:

Front fog light relay operates. (Front fog lights come on.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
3.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Using a voltmeter, check the signal reading of the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE AND BODY GROUND)

NG

INSPECT SEMICONDUCTOR PWR INTEGRATION ECU (RESULTS OF SIGNAL READING CHECK)

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE AND BODY GROUND)
a.

Remove the semiconductor pwr integration ECU from the No. 1 engine room relay block and No. 1 junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL

E288870C03
2.021,3.031 2.375,3.25 0.354,0.219 4.917,3.031 5.271,3.25 0.354,0.219 3.479,3.042 3.813,3.25 0.333,0.208 0.583,3.031 0.917,3.24 0.333,0.208 6.313,3.042 6.646,3.25 0.333,0.208 1,4.438 0.813,4.135 false 2.49,4.448 2.365,4.188 false 3.927,4.438 3.781,4.063 false 4.719,4.438 4.885,4.146 false 6.177,4.438 6.365,4.094 false 0.177,0.208 0.49,0.406 0.313,0.198 10 false *a 0.656,3.052 0.969,3.25 0.313,0.198 10 false 1A 2.104,3.052 2.417,3.25 0.313,0.198 10 false 1D 4.99,3.052 5.302,3.25 0.313,0.198 10 false 1G 6.396,3.063 6.708,3.26 0.313,0.198 10 false 1B 3.552,3.063 3.865,3.26 0.313,0.198 10 false 1E 0.885,4.469 1.344,4.667 0.458,0.198 10 false ALT 4.552,4.458 5.01,4.656 0.458,0.198 10 false GND2 2.333,4.479 2.792,4.677 0.458,0.198 10 false GND1 3.802,4.458 4.26,4.656 0.458,0.198 10 false TAIL 6.031,4.458 6.49,4.656 0.458,0.198 10 false BATT
*a Component without semiconductor pwr integration ECU connected
(No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-1 (BATT) - Body ground Always 11 to 14 V
1A-1 (ALT) - Body ground Always 11 to 14 V
1E-4 (TAIL) - Body ground Light control switch in tail position 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-14 (GND1) - Body ground Always Below 1 Ω
1G-5 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-7 (FOGS) - 4F-25 Always Below 1 Ω
1D-7 (FOGS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E259752C07
1.229,0.302 1.563,0.531 0.333,0.229 4.594,0.458 4.927,0.688 0.333,0.229 3.448,1.5 3.688,1.104 false 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.323,0.333 1.635,0.531 0.313,0.198 10 false 4F 4.677,0.5 4.99,0.698 0.313,0.198 10 false MB 3.24,1.531 3.708,1.688 0.469,0.156 10 false FFGO
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4F-25 - MB-7 (FFGO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - FOG LIGHT ASSEMBLY LH AND FOG LIGHT ASSEMBLY RH)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - FOG LIGHT ASSEMBLY LH AND FOG LIGHT ASSEMBLY RH)
a.

Disconnect the A15 fog light assembly LH connector.


b.

Disconnect the A23 fog light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-6 (FOGR) - A15-2 Always Below 1 Ω
1E-6 (FOGR) - A23-2 Always Below 1 Ω
1E-6 (FOGR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Replace the semiconductor pwr integration ECU with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Check that the front fog lights operate normally.

OK:

The front fog lights operate normally.



Result:
Proceed to
OK
NG



OK

END (SEMICONDUCTOR PWR INTEGRATION ECU WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)