Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019708 METER / GAUGE / DISPLAY _0104486 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM via the CAN communication system. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM

E143765
0.625,3.083 2.021,3.417 1.396,0.333 10 ECM 2.927,3.156 3.021,3.344 0.094,0.188 10 : 3.01,3.177 4.656,3.531 1.646,0.354 10 CAN Communication Line 5.292,3.104 7.156,3.438 1.865,0.333 10 Combination Meter Assembly

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TachoMeter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 -
Body Electrical > Combination Meter > Active Test
Tester Display
TachoMeter Operation
50004 122 2
OK:

Tachometer indication is normal.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ENGINE RPM)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS (ENGINE RPM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Rpm Engine speed Min.: 0 rpm, Max.: 12750 rpm Almost the same as actual tachometer -
Body Electrical > Combination Meter > Data List
Tester Display
Engine Rpm
50003 122 9
OK:

Engine speed displayed on the GTS is almost the same as the tachometer indication.


HINT:
·

When the data list values and tachometer values match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.

·

When the data list values and tachometer values do not match, an internal malfunction of the combination meter assembly is suspected.




Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK FOR DTC
a.

Check if SFI System DTCs are output.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 2GR-FE: Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. B



A

5.READ VALUE USING GTS (ENGINE SPEED, ENGINE RPM)

B

5.READ VALUE USING GTS (ENGINE SPEED, ENGINE RPM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for Engine: Powertrain / Engine / Data List.


ii.

for Combination Meter: Body Electrical / Combination Meter / Data List.



e.

Check the values by referring to the table below.

i.

Engine

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 610 to 710 rpm: Idling for 1AR-FE:
Idling (engine warmed up and A/C off): 660 rpm
for 2GR-FE:
Idling (engine warmed up and A/C off): 667 rpm
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9

ii.

Combination Meter

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Rpm Engine speed Min.: 0 rpm, Max.: 12750 rpm Almost the same as actual tachometer -
Body Electrical > Combination Meter > Data List
Tester Display
Engine Rpm
50003 122 9


Result:
Result Proceed to
The data list values of the ECUs do not match. A
The data list values of the ECUs match. B


HINT:
·

When the data list values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the data list values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.




A

6.REPLACE COMBINATION METER ASSEMBLY

B

6.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

OK:

The operation of the tachometer returns to normal.



Result:
Proceed to
OK
NG



OK

END

NG