This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B1500 | Fuel Sender Open Detected | When IG voltage is 9.5 V or more and the following condition is detected:
·
Average input signal of fuel sender gauge assembly is 550 Ω or more 3 times consecutively |
·
Harness or connector ·
Fuel sender gauge assembly ·
Combination meter assembly |
- | - |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input | Min.: 0 L, Max.: 172.5 L | Fuel receiver gauge indicates F: 64.8 L
Fuel receiver gauge indicates 3/4: 51.6 L Fuel receiver gauge indicates 1/2: 36.0 L Fuel receiver gauge indicates 1/4: 20.4 L Fuel receiver gauge indicates E: 7.2 L |
Unit: Liter |
| Tester Display |
|---|
| Fuel Input |
| Result | Proceed to |
|---|---|
| Fuel level data can be displayed on the GTS and DTC B1500 is output. | A |
| Fuel level data cannot be displayed on the GTS. | B |
A
B
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the F22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F22-14 (FR) - F22-15 (FE) | Always | 13.5 to 414.5 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F22 combination meter assembly connector.
Disconnect the M9 fuel suction tube with pump and gauge assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F22-14 (FR) - M9-2 (FS) | Always | Below 1 Ω |
| F22-15 (FE) - M9-3 (FE) | Always | Below 1 Ω |
| F22-14 (FR) - Body ground | Always | 10 kΩ or higher |
| F22-15 (FE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2GR-FE: Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Inspect the fuel sender gauge assembly.
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
for 2GR-FE: Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
Fuel sender gauge assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2GR-FE: Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
| *a | Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 (FS) - B-2 | Always | Below 1 Ω |
| A-3 (FE) - B-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2GR-FE: Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL