Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3160E _55 Steering _019697 POWER ASSIST SYSTEMS _0104490 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
C1551 IG Power Supply Voltage Open or short in IG power source circuit with ignition switch ON
·

EPS-IG fuse

·

IG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


EPS warning light: Comes on -

WIRING DIAGRAM

C250100E13
0.323,1.021 1.76,1.24 1.438,0.219 10 false from IG1 NO. 2 Relay 2.271,1.208 3.052,1.583 0.781,0.375 10 false EPS-IG 3.396,1.031 3.865,1.583 0.469,0.552 10 false pF1 5.083,1.042 5.479,1.344 0.396,0.302 10 false IG 3.479,0.844 3.833,1.167 0.354,0.323 10 false 5 4.792,0.854 5.021,1.083 0.229,0.229 10 false 1 4.802,1.938 5.094,2.24 0.292,0.302 10 false 2 5.073,2.146 5.75,2.469 0.677,0.323 10 false PGND 4.813,2.906 6.865,3.24 2.052,0.333 10 false Power Steering ECU Assembly 4.76,1.021 5.094,1.365 0.333,0.344 10 false p1 4.76,2.125 5.083,2.417 0.323,0.292 10 false p2 4.177,1.167 4.396,1.406 0.219,0.24 10 false * 3.615,2.281 3.958,2.688 0.344,0.406 10 false * 0.292,3.271 2.313,3.635 2.021,0.365 10 false *: ECU Wire Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (IG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING GTS (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "IG Power Supply" in the Data List and read the value displayed on the GTS.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply IG power source voltage Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Ignition switch ON
Chassis > EMPS > Data List
Tester Display
IG Power Supply
50003 142 11
OK:

The normal condition value is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C295176C01
0.542,0.521 0.896,0.813 0.354,0.292 1.906,1.375 2.323,1.375 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 2.365,1.292 2.677,1.49 0.313,0.198 10 false IG 0.604,0.573 0.917,0.771 0.313,0.198 10 false pF1
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the pF1 ECU wire sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
pF1-5 (IG) - Body ground Ignition switch ON 9 to 16 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240351C10
0.344,3.271 0.792,3.552 0.448,0.281 0.604,0.906 1.052,1.188 0.448,0.281 2.271,3.531 2.354,4.135 false 1.115,1.677 1.49,1.802 false 0.198,0.146 0.635,0.458 0.438,0.313 10 false *a 0.5,3.323 0.938,3.719 0.438,0.396 10 false p2 2.177,4.177 2.906,4.51 0.729,0.333 10 false PGND 0.917,1.583 1.344,1.948 0.427,0.365 10 false IG 0.771,0.958 1.156,1.344 0.385,0.385 10 false p1
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the pF1 connector to the ECU wire sub-assembly.


b.

Disconnect the p1 and p2 power steering ECU assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
p1-1 (IG) - Body ground Ignition switch ON 9 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
p2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY