Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3160E _55 Steering _019697 POWER ASSIST SYSTEMS _0104490 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552  PIG Power Supply Voltage  C1554  Power Supply Relay Failure  


DESCRIPTION

If a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop the power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
C1552 PIG Power Supply Voltage PIG power source circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


EPS warning light: Comes on -
C1554 Power Supply Relay Failure Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


EPS warning light: Comes on -

WIRING DIAGRAM

C296807E02
4.958,3.135 6.906,3.552 1.948,0.417 10 false Power Steering ECU Assembly 4.177,0.969 4.406,1.26 0.229,0.292 10 false * 4.885,2.125 5.115,2.417 0.229,0.292 10 false 2 4.958,2.948 5.188,3.24 0.229,0.292 10 false p2 5.104,2.271 5.594,2.615 0.49,0.344 10 false PGND 5.104,0.823 5.594,1.167 0.49,0.344 10 false PIG 3.948,2.427 4.177,2.719 0.229,0.292 10 false * 3.167,0.813 3.531,1.156 0.365,0.344 10 false Fp1 3.219,0.604 3.448,0.896 0.229,0.292 10 false 1 4.885,0.698 5.115,0.99 0.229,0.292 10 false 1 0.833,1.385 1.552,1.813 0.719,0.427 10 false FL MAIN 1,2.448 1.719,2.875 0.719,0.427 10 false Battery 1.75,0.99 2.135,1.49 0.385,0.5 10 false EPS 0.531,3.365 2.427,3.74 1.896,0.375 10 false *: ECU Wire Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (PIG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING GTS (PIG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "PIG Power Supply" in the Data List and read the value displayed on the GTS.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to active motor Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Always
Chassis > EMPS > Data List
Tester Display
PIG Power Supply
50003 142 10
OK:

The normal condition value is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C295177C01
0.479,0.479 0.854,0.771 0.375,0.292 1.823,1.188 2.344,1.188 true 0.146,0.135 0.469,0.417 0.323,0.281 10 false *a 0.563,0.531 0.885,0.813 0.323,0.281 10 false Fp1 2.406,1.104 2.729,1.385 0.323,0.281 10 false PIG
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the Fp1 ECU wire sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Fp1-1 (PIG) - Body ground Always 9 to 16 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240344C08
0.229,1 0.677,1.281 0.448,0.281 2.146,1.188 2.229,1.781 false 1.198,1.198 1.115,1.792 false 0.146,0.125 0.74,0.552 0.594,0.427 10 false *a 0.385,1.042 0.844,1.365 0.458,0.323 10 false p2 2.094,1.833 2.896,2.177 0.802,0.344 10 false PGND 1.021,1.823 1.521,2.146 0.5,0.323 10 false PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the Fp1 connector to the ECU wire sub-assembly.


b.

Disconnect the p2 power steering ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
p2-1 (PIG) - Body ground Always 9 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
p2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY