Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM3160E _59 Vehicle Exterior _019718 SLIDING ROOF / CONVERTIBLE _0106110 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof does not Move by Operating Sliding Roof Control Switch  


DESCRIPTION

The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals when the sliding roof switch (map light assembly) is operated and drives its built-in motor.

WIRING DIAGRAM

B361723
1.333,1.083 3,1.5 1.667,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 3.083,0.917 4.75,1.333 1.667,0.417 10 false Instrument Panel Junction Block Assembly 1.542,4.729 3.427,5.073 1.885,0.344 10 false Sliding Roof Switch (Map Light Assembly) 1.542,4.563 1.854,4.76 0.313,0.198 10 false S1 5.167,4.75 5.479,4.948 0.313,0.198 10 false S5 5.167,4.917 7.083,5.333 1.917,0.417 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 2.792,2.698 3.25,2.896 0.458,0.198 10 false OPN 2.833,3.073 3.292,3.271 0.458,0.198 10 false CLS 2.656,3.552 3.115,3.75 0.458,0.198 10 false DOWN 2.896,3.927 3.354,4.125 0.458,0.198 10 false UP 2.792,4.25 3.25,4.448 0.458,0.198 10 false GND 1.615,2.188 3.031,2.406 1.417,0.219 10 false from IG1 NO. 2 Relay 4.115,2.344 4.615,2.563 0.5,0.219 10 false ECU-IG 2.167,1.719 3,1.938 0.833,0.219 10 false from Battery 4.104,1.885 4.688,2.104 0.583,0.219 10 false S/ROOF 5.792,2.802 6.25,3 0.458,0.198 10 false OPN 5.792,3.156 6.25,3.354 0.458,0.198 10 false CLS 5.792,3.656 6.25,3.854 0.458,0.198 10 false DWN 5.792,4.042 6.25,4.24 0.458,0.198 10 false UP 5.792,4.375 6.25,4.573 0.458,0.198 10 false E 3.219,2.688 3.583,2.906 0.365,0.219 10 false 17 3.219,3.063 3.583,3.281 0.365,0.219 10 false 16 3.26,3.552 3.625,3.771 0.365,0.219 10 false 5 3.271,3.938 3.635,4.156 0.365,0.219 10 false 6 3.271,4.26 3.635,4.479 0.365,0.219 10 false 1 5.531,2.698 5.896,2.917 0.365,0.219 10 false 7 5.521,3.073 5.885,3.292 0.365,0.219 10 false 5 5.521,3.542 5.885,3.76 0.365,0.219 10 false 6 5.521,3.927 5.885,4.146 0.365,0.219 10 false 4 5.49,4.26 5.854,4.479 0.365,0.219 10 false 12 5.51,1.625 5.875,1.844 0.365,0.219 10 false 8 5.51,2.083 5.875,2.302 0.365,0.219 10 false 1 5.792,2.156 6.25,2.354 0.458,0.198 10 false IG 5.792,1.708 6.25,1.906 0.458,0.198 10 false B 0.813,5.427 2.5,5.656 1.688,0.229 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD



PROCEDURE

1.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check the power window control system operates normally.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK

OK:

The power window control system operates normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal OFF or ON OFF: OPEN switch not pressed
ON: OPEN switch pressed
-
Close Switch CLOSE switch signal OFF or ON OFF: CLOSE switch not pressed
ON: CLOSE switch pressed
-
Up Switch UP switch signal OFF or ON OFF: UP switch not pressed
ON: UP switch pressed
-
Down Switch DOWN switch signal OFF or ON OFF: DOWN switch not pressed
ON: DOWN switch pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
Up Switch
Down Switch
50003 147 1,4,7,10
OK:

The GTS display changes according to switch operation as shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

3.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)
3.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)
a.

Remove the sliding roof switch (map light assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the sliding roof switch (map light assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)

NG

REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
a.

Disconnect the S1 sliding roof switch (map light assembly) connector.


b.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-5 (CLS) - S1-16 (CLS) Always Below 1 Ω
S5-5 (CLS) or S1-16 (CLS) - Body ground Always 10 kΩ or higher
S5-7 (OPN) - S1-17 (OPN) Always Below 1 Ω
S5-7 (OPN) or S1-17 (OPN) - Body ground Always 10 kΩ or higher
S5-6 (DWN) - S1-5 (DOWN) Always Below 1 Ω
S5-6 (DWN) or S1-5 (DOWN) - Body ground Always 10 kΩ or higher
S5-4 (UP) - S1-6 (UP) Always Below 1 Ω
S5-4 (UP) or S1-6 (UP) - Body ground Always 10 kΩ or higher
S1-1 (GND) - Body ground Always Below 1 Ω
S5-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR