Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM3160E _59 Vehicle Exterior _019718 SLIDING ROOF / CONVERTIBLE _0106110 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.

When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2341 Sensor (Motor) Failure Sensor (motor) failure (When the sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the motor)
·

Sliding roof ECU (Sliding roof drive gear sub-assembly)

·

Sliding roof switch (Map light assembly)

·

Wire harness or connector


B2344 Position Failure Position failure (When the sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the gear position)
·

Sliding roof ECU (Sliding roof drive gear sub-assembly)

·

Sliding roof switch (Map light assembly)

·

Wire harness or connector



WIRING DIAGRAM

B361719E01
1.323,1.417 2.5,1.99 1.177,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 2.583,1.167 4.25,1.583 1.667,0.417 10 false Instrument Panel Junction Block Assembly 1.417,4.417 3,4.833 1.583,0.417 10 false Sliding Roof Switch (Map Light Assembly) 1.417,4.25 1.729,4.448 0.313,0.198 10 false S1 4.615,4.833 4.927,5.031 0.313,0.198 10 false S5 4.615,5.021 6.531,5.521 1.917,0.5 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 0.677,5.458 4.344,5.656 3.667,0.198 10 false : LIN Communication Line 5.083,2.708 5.698,2.906 0.615,0.198 10 false OPN 5.083,2.958 5.698,3.156 0.615,0.198 10 false CLS 5.083,3.469 5.698,3.667 0.615,0.198 10 false DWN 5.083,3.719 5.698,3.917 0.615,0.198 10 false UP 5.083,3.969 5.698,4.167 0.615,0.198 10 false E 2.75,2.615 3.365,2.813 0.615,0.198 10 false OPN 2.781,2.854 3.396,3.052 0.615,0.198 10 false CLS 2.615,3.365 3.229,3.563 0.615,0.198 10 false DOWN 2.854,3.604 3.469,3.802 0.615,0.198 10 false UP 2.75,3.854 3.365,4.052 0.615,0.198 10 false GND 3.177,2.615 3.49,2.813 0.313,0.198 10 false 17 3.177,2.854 3.49,3.052 0.313,0.198 10 false 16 3.219,3.604 3.531,3.802 0.313,0.198 10 false 6 3.219,3.354 3.531,3.552 0.313,0.198 10 false 5 3.219,3.854 3.531,4.052 0.313,0.198 10 false 1 4.771,3.844 5.083,4.042 0.313,0.198 10 false 12 4.802,3.604 5.083,3.833 0.281,0.229 10 false 4 4.802,3.354 5.083,3.563 0.281,0.208 10 false 6 4.802,2.854 5.115,3.052 0.313,0.198 10 false 5 4.802,2.604 5.115,2.802 0.313,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD



PROCEDURE

1.CHECK SLIDING ROOF OPERATION
a.

Check the sliding roof auto operation function.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK

OK:

Auto operation function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT

NG

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
2.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

OK:

Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
a.

Disconnect the S1 sliding roof switch (map light assembly) connector.


b.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-5 (CLS) - S1-16 (CLS) Always Below 1 Ω
S5-5 (CLS) or S1-16 (CLS) - Body ground Always 10 kΩ or higher
S5-7 (OPN) - S1-17 (OPN) Always Below 1 Ω
S5-7 (OPN) or S1-17 (OPN) - Body ground Always 10 kΩ or higher
S5-6 (DWN) - S1-5 (DOWN) Always Below 1 Ω
S5-6 (DWN) or S1-5 (DOWN) - Body ground Always 10 kΩ or higher
S5-4 (UP) - S1-6 (UP) Always Below 1 Ω
S5-4 (UP) or S1-6 (UP) - Body ground Always 10 kΩ or higher
S1-1 (GND) - Body ground Always Below 1 Ω
S5-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)
a.

Remove the sliding roof switch (map light assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the sliding roof switch (map light assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)