Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106113 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

WIRING DIAGRAM

B361445
0.083,0.542 1,0.771 0.917,0.229 10 false from Battery 1.323,0.719 1.781,0.917 0.458,0.198 10 false A/C 2.677,0.458 2.99,0.656 0.313,0.198 10 false 11 2.677,1.125 2.99,1.323 0.313,0.198 10 false 12 2.958,0.563 3.115,0.76 0.156,0.198 10 false B 2.948,1.229 3.406,1.427 0.458,0.198 10 false GND 2,2.198 2.656,2.396 0.656,0.198 10 false I7*1, H7*2 2,2.344 5.115,2.573 3.115,0.229 10 false Power Window Regulator Master Switch Assembly 3.781,0.552 4.094,0.75 0.313,0.198 10 false UP 3.531,1.229 4.146,1.427 0.615,0.198 10 false DOWN 4.094,0.448 4.406,0.646 0.313,0.198 10 false 20 4.083,1.115 4.396,1.313 0.313,0.198 10 false 15 5.458,0.563 5.771,0.76 0.313,0.198 10 false UP 5.458,1.229 6.073,1.427 0.615,0.198 10 false DOWN 1.708,4.115 3.333,4.49 1.625,0.375 10 false Instrument Panel Junction Block Assembly 3.521,4.208 5.177,4.552 1.656,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 0.604,5.063 1.521,5.292 0.917,0.229 10 false from Battery 1.885,5.229 2.667,5.625 0.781,0.396 10 false P/W F/L*1, P/W F/R*2 0.875,6.354 4.542,6.552 3.667,0.198 10 false : LIN Communication Line 5.25,4.969 5.406,5.167 0.156,0.198 10 false 2 5.25,5.406 5.406,5.604 0.156,0.198 10 false 1 5.458,5.094 5.615,5.292 0.156,0.198 10 false B 5.469,5.521 5.927,5.719 0.458,0.198 10 false GND 5.073,5.802 5.76,6.01 0.688,0.208 10 false I4*1, H4*2 5.073,5.979 7.031,6.323 1.958,0.344 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.156,0.448 5.333,0.635 0.177,0.188 10 false 10 5.219,1.104 5.531,1.302 0.313,0.198 10 false 7 3.052,6.031 3.969,6.26 0.917,0.229 10 false *1: for LHD 3.052,6.344 3.969,6.573 0.917,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD



PROCEDURE

1.READ VALUE USING GTS (MAIN BODY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Communication D-Door Motor Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) STOP or OK STOP: Communication stopped
OK: Normal communication
-
Communication Master SW Connection status between power window regulator master switch assembly and main body ECU (multiplex network body ECU) STOP or OK STOP: Communication stopped
OK: Normal communication
-
Body Electrical > Main Body > Data List
Tester Display
Communication D-Door Motor
Communication Master SW
50003 123 49,70
OK:

On the GTS screen, OK is displayed.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (D-DOOR MOTOR)

NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)

2.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Enter the following menus: Body Electrical / D-Door Motor / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated
-
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (D-DOOR MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))
3.PERFORM ACTIVE TEST USING GTS (D-DOOR MOTOR)
a.

Enter the following menus: Body Electrical / D-Door Motor / Active Test.


b.

Perform the Active Test according to the display on the GTS.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
OK:

Driver door power window operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))
a.

Disconnect the I7*1 or H7*2 power window regulator master switch assembly connector.


b.

Disconnect the I4*1 or H4*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I7-20 (UP) - I4-10 (UP) Always Below 1 Ω
I7-20 (UP) or I4-10 (UP) - Body ground Always 10 kΩ or higher
I7-15 (DOWN) - I4-7 (DOWN) Always Below 1 Ω
I7-15 (DOWN) or I4-7 (DOWN) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H7-20 (UP) - H4-10 (UP) Always Below 1 Ω
H7-20 (UP) or H4-10 (UP) - Body ground Always 10 kΩ or higher
H7-15 (DOWN) - H4-7 (DOWN) Always Below 1 Ω
H7-15 (DOWN) or H4-7 (DOWN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Replace the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK MANUAL UP / DOWN FUNCTION (FOR DRIVER DOOR)
6.CHECK MANUAL UP / DOWN FUNCTION (FOR DRIVER DOOR)
a.

Check that the driver door power window moves when the manual up and down function of the power window regulator master switch assembly is operated.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK

OK:

Driver door manual up and down function is normal.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)