Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106113 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  B2311  Power Window Motor Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the power window regulator master switch assembly, power window regulator switch assembly or a rear power window regulator switch assembly. The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is output when a power window regulator motor assembly is malfunctioning, or the ECU built into the power window regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

D-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction

Either condition is met:

(a)

Power window regulator motor assembly (for driver door) is malfunctioning

(b)

When ECU in power window regulator motor assembly (for driver door) determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for driver door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for driver door)

·

Wire harness or connector



P-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction

Either condition is met:

(a)

Power window regulator motor assembly (for front passenger door) is malfunctioning

(b)

When ECU in power window regulator motor assembly (for front passenger door) determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for front passenger door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for front passenger door)

·

Wire harness or connector



RL-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction

Either condition is met:

(a)

Power window regulator motor assembly (for rear LH door) is malfunctioning

(b)

When ECU in power window regulator motor assembly (for rear LH door) determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for rear LH door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for rear LH door)

·

Wire harness or connector



RR-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction

Either condition is met:

(a)

Power window regulator motor assembly (for rear RH door) is malfunctioning

(b)

When ECU in power window regulator motor assembly (for rear RH door) determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for rear RH door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for rear RH door)

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2311 is stored in each power window regulator motor assembly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION

·

If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124
Body Electrical > P-Door Motor > Clear DTCs
50002 144
Body Electrical > RL-Door Motor > Clear DTCs
50002 146
Body Electrical > RR-Door Motor > Clear DTCs
50002 145

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145
OK:

DTC B2311 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check the parts which the DTCs have been output from.


Result:
Result Proceed to
DTC output from power window regulator motor assembly (for driver door) A
DTC output from power window regulator motor assembly (for front passenger door) B
DTC output from power window regulator motor assembly (for rear LH door) C
DTC output from power window regulator motor assembly (for rear RH door) D



A

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) - BATTERY AND BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) - BATTERY AND BODY GROUND)

C

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) - BATTERY AND BODY GROUND)

D

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) - BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I4-2 (B) - I4-1 (GND) Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
H4-2 (B) - H4-1 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I4-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
H4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) - BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
H5-2 (B) - H5-1 (GND) Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
I5-2 (B) - I5-1 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
H5-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
I5-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) - BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-2 (B) - K2-1 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) - BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J2-2 (B) - J2-1 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / (desired system) / Active Test.

HINT:

Perform the Active Test for the power window regulator motor assembly that has DTC B2311 stored in its ECU.



e.

Perform the Active Test according to the display on the GTS.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > P-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > RL-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > RR-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
Body Electrical > P-Door Motor > Active Test
Tester Display
Power Window
50004 144 1
Body Electrical > RL-Door Motor > Active Test
Tester Display
Power Window
50004 146 1
Body Electrical > RR-Door Motor > Active Test
Tester Display
Power Window
50004 145 1
OK:

Each power window motor operates.



Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window)
NG (Rear LH door power window) C
NG (Rear RH door power window)



A

8.PERFORM INITIALIZATION (APPLICABLE LOCATION)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR)

8.PERFORM INITIALIZATION (APPLICABLE LOCATION)
a.

Initialize the power window regulator motor assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION

HINT:

Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.



Result:
Proceed to
NEXT



NEXT

9.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)
9.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)
a.

Check that the power window operates normally by opening and closing the window.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK

HINT:

Check the power window operation of the window where DTC B2311 has been stored.


OK:

Each power window operates normally.



Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window)
NG (Rear LH door power window) C
NG (Rear RH door power window)



A

10.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR)

10.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.



Result:
Proceed to
OK
NG



OK

11.CHECK DTC OUTPUT

NG

INSTALL PARTS CORRECTLY

11.CHECK DTC OUTPUT
a.

Turn the ignition switch off.


b.

Wait for at least 10 seconds, and then turn the ignition switch to ON.


c.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145
OK:

DTC B2311 is not output.



Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window)
NG (Rear LH door power window) C
NG (Rear RH door power window)



A

END

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR)