Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106114 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)  Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>INITIALIZATION

WIRING DIAGRAM

B185318
0.979,0.813 3.031,1.125 2.052,0.313 10 false Power Window Regulator Master Switch Assembly 3.51,0.813 7.135,1.167 3.625,0.354 10 false Power Window Regulator Motor Assembly (for Driver Door) 0.667,1.448 2.677,1.688 2.01,0.24 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>INITIALIZATION



HINT:

If the pulse sensor built into the power window regulator motor assembly (for driver door) is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator master switch assembly at the auto up position, and opened manually by pushing down the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>FAIL-SAFE CHART


PROCEDURE

1.READ VALUE USING GTS (MASTER SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Master switch / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Master Switch > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal OFF or ON OFF: Driver door power window auto switch not being operated
ON: Driver door power window auto switch being operated
-
Body Electrical > Master Switch > Data List
Tester Display
D Door P/W Auto SW
50003 148 1
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (D-DOOR MOTOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

2.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Enter the following menus: Body Electrical / D-Door Motor / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal OFF or ON OFF: Driver door power window auto switch not being operated
ON: Driver door power window auto switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Auto SW
50003 124 1
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

3.PERFORM INITIALIZATION (FOR DRIVER DOOR)

NG

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
3.PERFORM INITIALIZATION (FOR DRIVER DOOR)

Result:
Proceed to
NEXT



NEXT

4.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
4.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
a.

Check that the driver door power window moves when the auto up and down function of the power window regulator master switch assembly is operated.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>OPERATION CHECK

OK:

Driver door auto up and down function is normal.



Result:
Proceed to
OK
NG



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Replace the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
6.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
a.

Check that the driver door power window moves when the auto up and down function of the power window regulator master switch assembly is operated.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>OPERATION CHECK

OK:

Driver door auto up and down function is normal.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)