Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106114 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)  Key-off Operation Function Operates even if Operating Conditions are not Satisfied  


DESCRIPTION

·

When the front doors are closed, each power window regulator motor assembly can control its power window operation for approximately 43 seconds after the ignition switch is turned from ON to off by receiving operation permission signals from the main body ECU (multiplex network body ECU).

·

However, when approximately 43 seconds have elapsed, or the driver door or front passenger door is opened within approximately 43 seconds of the ignition switch being turned off, the power window regulator motor assembly stops operating.

·

During auto operation, when 43 seconds have elapsed and key-off operation is prohibited, the window continues the operation until the auto operation is completed.


CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD



PROCEDURE

1.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual up and down function using the power window regulator master switch assembly, power window regulator switch assembly and rear power window regulator switch assembly (for LH or RH door) can operate the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>OPERATION CHECK

OK:

Manual up and down function is normal.



Result:
Proceed to
OK
NG



OK

2.CHECK REMOTE UP / DOWN FUNCTION

NG

2.CHECK REMOTE UP / DOWN FUNCTION
a.

Check that the remote up and down function using the power window regulator master switch assembly can operate all the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>OPERATION CHECK

OK:

Remote up and down function is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK KEY-OFF OPERATION FUNCTION

NG

3.CHECK KEY-OFF OPERATION FUNCTION

Result:
Result Proceed to
Power window can still be operated even after opening driver door or front passenger door within approximately 43 seconds of ignition switch being turned off A
Power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for All Doors) B
Power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for Driver Door or Front Passenger Door) C
Power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for Rear LH Door or Rear RH Door) D



A

4.READ VALUE USING GTS (MAIN BODY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR)

D

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
4.READ VALUE USING GTS (MAIN BODY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly (for RH) signal OFF or ON OFF: Front door RH closed
ON: Front door RH open
-
FL Door Courtesy SW Front door courtesy light switch assembly (for LH) signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit)

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK KEY-OFF OPERATION FUNCTION
6.CHECK KEY-OFF OPERATION FUNCTION
a.

Check the key-off operation function.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>OPERATION CHECK

OK:

Key-off operation function is normal.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY