Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106114 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the power window regulator master switch assembly or power window regulator switch assembly. The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is output when the ECU built into a power window regulator motor assembly and power window regulator master switch assembly determine that the power window regulator master switch assembly or power window regulator switch assembly is stuck.

Master Switch
DTC No. Detection Item DTC Detection Condition Trouble Area
B2312 Power Window Switch Malfunction
·

Power window regulator master switch assembly stuck

·

Power window regulator master switch assembly held in same position for more than 20 seconds


Power window regulator master switch assembly

D-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2312 Power Window Switch Malfunction
·

Power window regulator master switch assembly stuck

·

Power window regulator master switch assembly held in same position for more than 20 seconds


·

Power window regulator master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector



P-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2312 Power Window Switch Malfunction
·

Power window regulator switch assembly stuck

·

Power window regulator switch assembly held in same position for more than 20 seconds


·

Power window regulator switch assembly

·

Power window regulator motor assembly (for front passenger door)

·

Wire harness or connector



WIRING DIAGRAM

B351360
2.323,0.365 2.479,0.563 0.156,0.198 10 false 3 5.615,1.865 5.771,2.063 0.156,0.198 10 false 1 2.323,1.177 2.479,1.375 0.156,0.198 10 false 4 2.323,1.542 2.479,1.74 0.156,0.198 10 false 5 0.75,2.083 1.146,2.281 0.396,0.198 10 false GND 3.74,1.156 3.99,1.344 0.25,0.188 10 false 10 3.802,1.542 3.958,1.74 0.156,0.198 10 false 7 5.625,1.188 5.781,1.385 0.156,0.198 10 false 2 2.323,4.542 2.479,4.74 0.156,0.198 10 false 8 0.552,1.969 0.708,2.167 0.156,0.198 10 false 1 5.625,3.844 5.781,4.042 0.156,0.198 10 false 2 5.625,4.531 5.781,4.729 0.156,0.198 10 false 1 2.323,3.823 2.479,4.021 0.156,0.198 10 false 5 2.323,4.063 2.479,4.26 0.156,0.198 10 false 4 2.323,4.302 2.479,4.5 0.156,0.198 10 false 2 3.74,3.833 3.99,4.021 0.25,0.188 10 false 10 3.792,4.052 3.948,4.25 0.156,0.198 10 false 7 3.792,4.302 3.948,4.5 0.156,0.198 10 false 5 3.792,4.542 3.948,4.74 0.156,0.198 10 false 4 0.563,4.51 0.719,4.708 0.156,0.198 10 false 7 4.688,0.146 5.552,0.365 0.865,0.219 10 false from Battery 5.979,0.583 6.479,0.76 0.5,0.177 10 false A/C 5.833,4.094 6.552,4.323 0.719,0.229 10 false P/W F/L 5.865,1.417 6.583,1.646 0.719,0.229 10 false P/W F/R 2.01,1.26 2.313,1.458 0.302,0.198 10 false UP 3.979,1.271 4.281,1.469 0.302,0.198 10 false UP 3.979,3.938 4.281,4.135 0.302,0.198 10 false UP 2.115,0.448 2.354,0.667 0.24,0.219 10 false B 5.417,1.281 5.656,1.5 0.24,0.219 10 false B 5.406,3.948 5.646,4.167 0.24,0.219 10 false B 5.229,4.656 5.625,4.854 0.396,0.198 10 false GND 0.76,4.656 1.156,4.854 0.396,0.198 10 false GND 5.229,1.99 5.625,2.188 0.396,0.198 10 false GND 2,3.948 2.302,4.146 0.302,0.198 10 false UP 1.76,4.156 2.26,4.344 0.5,0.188 10 false DOWN 1.771,1.646 2.271,1.833 0.5,0.188 10 false DOWN 3.969,4.177 4.469,4.365 0.5,0.188 10 false DOWN 3.969,1.656 4.469,1.844 0.5,0.188 10 false DOWN 2.052,4.417 2.365,4.615 0.313,0.198 10 false IG 3.979,4.646 4.479,4.844 0.5,0.198 10 false AUTO 3.979,4.406 4.292,4.604 0.313,0.198 10 false IG 1.833,4.635 2.333,4.833 0.5,0.198 10 false AUTO 4.844,6.615 6.51,6.823 1.667,0.208 10 false : LIN Communication Line 0.635,2.865 2.208,3.25 1.573,0.385 10 false Power Window Regulator Master Switch Assembly 0.646,2.708 1.042,2.927 0.396,0.219 10 false H6 3.781,2.583 4.177,2.802 0.396,0.219 10 false H4 0.698,5.26 1.094,5.479 0.396,0.219 10 false I8 3.781,2.74 5.729,3.135 1.948,0.396 10 false Power Window Regulator Motor Assembly (for Driver Door) 3.771,5.229 4.167,5.448 0.396,0.219 10 false I5 0.698,5.417 2.26,5.802 1.563,0.385 10 false Power Window Regulator Switch Assembly 3.76,5.385 6.344,5.854 2.583,0.469 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 0.031,7.021 1.688,7.469 1.656,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 1.781,6.844 3.438,7.292 1.656,0.448 10 false Instrument Panel Junction Block Assembly 1.885,0.729 2.281,0.917 0.396,0.188 10 false PWS 2.302,0.604 2.5,0.792 0.198,0.188 10 false 13 3.167,0.698 4.469,0.938 1.302,0.24 10 false from PWR Relay

CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 is stored in the power window regulator master switch assembly and in each power window regulator motor assembly.

·

If the power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>HOW TO PROCEED WITH TROUBLESHOOTING

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD



HINT:

If DTC B2312 is not output again after the DTC has been cleared, the DTC was output due to the switch being held.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>DTC CHECK / CLEAR

Body Electrical > Master Switch > Clear DTCs
50002 148
Body Electrical > D-Door Motor > Clear DTCs
50002 124
Body Electrical > P-Door Motor > Clear DTCs
50002 144

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>DTC CHECK / CLEAR

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
OK:

DTC B2312 is not output.



Result:
Proceed to
OK
NG



OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

NG

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check the parts which the DTCs have been output from.


Result:
Result Proceed to
DTC output from power window regulator master switch assembly A
DTC output from power window regulator motor assembly (for driver door) B
DTC output from power window regulator motor assembly (for front passenger door) C



A

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

3.READ VALUE USING GTS (D-DOOR MOTOR)

C

7.READ VALUE USING GTS (P-DOOR MOTOR)
3.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / D-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated
-
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))
4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))
a.

Disconnect the H6 power window regulator master switch assembly connector.


b.

Disconnect the H4 power window regulator motor assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-4 (UP) - Body ground Always 10 kΩ or higher
H6-5 (DOWN) - Body ground Always 10 kΩ or higher
H4-10 (UP) - Body ground Always 10 kΩ or higher
H4-7 (DOWN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Replace the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124
OK:

DTC B2312 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

7.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / P-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto switch not being operated
ON: Front passenger door power window auto switch being operated
-
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated
-
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated
-
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
P Door P/W Up SW
P Door P/W Down SW
50003 144 1,2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

8.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
8.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.

Remove the power window regulator switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL


b.

Inspect the power window regulator switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))
a.

Disconnect the I5 power window regulator motor assembly (for front passenger door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I8-5 (UP) - Body ground Always 10 kΩ or higher
I8-4 (DOWN) - Body ground Always 10 kΩ or higher
I8-8 (AUTO) - Body ground Always 10 kΩ or higher
I5-10 (UP) - Body ground Always 10 kΩ or higher
I5-7 (DOWN) - Body ground Always 10 kΩ or higher
I5-4 (AUTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR