Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106121 WINDOW DEFOGGER SYSTEM J

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  Rear Window Defogger System does not Operate  


DESCRIPTION

When the rear window defogger switch on the air conditioning control assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the semiconductor pwr integration ECU to operate the window defogger system.

WIRING DIAGRAM

B364274E02
0.75,7.406 2.417,7.573 1.667,0.167 10 false : LIN Communication Line 2.5,6.99 4.469,7.323 1.969,0.333 10 false Back Door Glass (Rear Window Defogger Wire) 2.5,5.667 4.469,6 1.969,0.333 10 false Back Door Glass (Rear Window Defogger Wire) 2.5,5.5 2.75,5.667 0.25,0.167 10 false Y2 2.49,6.573 2.833,6.74 0.344,0.167 10 false X17 3.844,6.573 4.167,6.74 0.323,0.167 10 false X16 2.552,6.375 2.75,6.542 0.198,0.167 10 false 1 3.906,6.375 4.104,6.542 0.198,0.167 10 false 1 4.333,6.479 4.531,6.646 0.198,0.167 10 false *2 4.167,5.125 4.365,5.292 0.198,0.167 10 false *1 5.167,7 6.917,7.167 1.75,0.167 10 false *1: w/ Glass Hatch Opener 5.167,7.333 6.917,7.5 1.75,0.167 10 false *2: w/o Glass Hatch Opener 5.531,6.021 7.083,6.354 1.552,0.333 10 false Air Conditioning Amplifier Assembly 2.667,5.125 2.833,5.292 0.167,0.167 10 false 2 3.813,5.125 3.979,5.292 0.167,0.167 10 false 1 2.688,4.292 3.917,4.625 1.229,0.333 10 false Semiconductor Pwr Integration ECU 5.521,5.833 5.792,6 0.271,0.167 10 false F80 5.594,0.292 5.823,0.458 0.229,0.167 10 false 37 5.583,1.813 5.813,1.979 0.229,0.167 10 false 38 5.594,5.219 5.823,5.385 0.229,0.167 10 false 14 5.854,5.333 6.25,5.5 0.396,0.167 10 false GND 5.854,1.917 6.333,2.083 0.479,0.167 10 false RDEF 5.854,0.479 6.25,0.646 0.396,0.167 10 false LIN1 3.813,0.333 4.083,0.5 0.271,0.167 10 false 8 3.406,0.469 3.802,0.635 0.396,0.167 10 false LIN1 2.333,0.917 2.865,1.156 0.531,0.24 10 false F32 2.333,1.083 4.5,1.25 2.167,0.167 10 false Air Conditioning Control Assembly 3.573,1.927 4,2.094 0.427,0.167 10 false DEFS 3.573,3.729 4,3.896 0.427,0.167 10 false RDEF 4.115,1.927 4.333,2.094 0.219,0.167 10 false 1D 4.115,3.719 4.333,3.885 0.219,0.167 10 false 1C 4.156,3.521 4.333,3.688 0.177,0.167 10 false 1 4.156,1.729 4.333,1.896 0.177,0.167 10 false 5 2.635,1.927 3.083,2.094 0.448,0.167 10 false BATT 2.635,2.427 3,2.594 0.365,0.167 10 false ALT 2.635,2.938 3,3.104 0.365,0.167 10 false IGN 2.635,3.448 3.083,3.615 0.448,0.167 10 false GND1 2.635,3.948 3.083,4.115 0.448,0.167 10 false GND2 2.271,3.948 2.5,4.115 0.229,0.167 10 false 1G 2.271,3.448 2.5,3.615 0.229,0.167 10 false 1D 2.271,2.938 2.5,3.104 0.229,0.167 10 false 1D 2.271,2.427 2.5,2.594 0.229,0.167 10 false 1A 2.271,1.927 2.5,2.094 0.229,0.167 10 false 1B 2.313,1.729 2.51,1.896 0.198,0.167 10 false 1 2.313,2.229 2.51,2.396 0.198,0.167 10 false 1 2.271,2.74 2.5,2.906 0.229,0.167 10 false 11 2.271,3.25 2.5,3.417 0.229,0.167 10 false 14 1.51,3.083 2.198,3.271 0.688,0.188 10 false IG1 NO. 3 2.313,3.75 2.51,3.917 0.198,0.167 10 false 5 0.344,1.917 1.177,2.083 0.833,0.167 10 false from Battery 0.198,2.427 1.167,2.594 0.969,0.167 10 false from ALT Fuse 0.198,2.927 1.188,3.323 0.99,0.396 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the battery voltage is low, the window defogger system may not operate. In this case, check the Data List item "Battery Control Count (Body ECU)".

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

HINT:

Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly through the same communication line.


OK:

The air conditioning system operates normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger Relay (Rear) Back door glass (Rear window defogger wire) OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Defogger Relay (Rear)
50004 121 22
OK:

The rear window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

3.REPLACE AIR CONDITIONING CONTROL ASSEMBLY

NG

4.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
3.REPLACE AIR CONDITIONING CONTROL ASSEMBLY
a.

Replace the air conditioning control assembly with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.

Check that the window defogger system operates normally.

Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>OPERATION CHECK

OK:

The window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING CONTROL ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Using a voltmeter, check the signal reading of the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE AND BODY GROUND)

NG

INSPECT SEMICONDUCTOR PWR INTEGRATION ECU (RESULTS OF SIGNAL READING CHECK)

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE AND BODY GROUND)
a.

Remove the semiconductor pwr integration ECU from the No. 1 engine room relay block and No. 1 junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL

B352092C06
0.75,3.063 1.083,3.271 0.333,0.208 2.542,3.073 2.875,3.281 0.333,0.208 4.292,3.073 4.625,3.281 0.333,0.208 6.094,3.052 6.427,3.26 0.333,0.208 1.427,4.417 1.083,4.135 false 3.208,4.49 2.906,4.219 false 4.052,4.438 4.26,4.188 false 5.906,4.396 6.115,4.146 false 0.552,0.448 0.865,0.646 0.313,0.198 10 false *a 0.833,3.083 1.146,3.281 0.313,0.198 10 false 1A 4.375,3.094 4.688,3.292 0.313,0.198 10 false 1G 6.177,3.073 6.49,3.271 0.313,0.198 10 false 1B 2.625,3.094 2.938,3.292 0.313,0.198 10 false 1D 1.323,4.427 1.781,4.625 0.458,0.198 10 false ALT 3.063,4.521 3.677,4.719 0.615,0.198 10 false GND1 3.865,4.469 4.479,4.667 0.615,0.198 10 false GND2 5.708,4.417 6.323,4.615 0.615,0.198 10 false BATT
*a Component without semiconductor pwr integration ECU
(No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-1 (BATT) - Body ground Always 11 to 14 V
1A-1 (ALT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-14 (GND1) - Body ground Always Below 1 Ω
1G-5 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F80 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F80-38 (RDFG) - 1D-5 (DEFS) Always Below 1 Ω
F80-38 (RDFG) or 1D-5 (DEFS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Install the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSTALLATION


b.
B364280C02
1.396,0.26 1.865,0.542 0.469,0.281 2.49,1.844 2.417,1.542 false 0.438,0.323 0.75,0.521 0.313,0.198 10 false *a 1.51,0.323 1.969,0.521 0.458,0.198 10 false F80 2.396,1.896 3.01,2.094 0.615,0.198 10 false RDEF
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F80-38 (RDFG) - Body ground Ignition switch ON, rear window defogger switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the F80 air conditioning amplifier assembly connector.


b.
E285437C08
1.833,0.385 2.25,0.635 0.417,0.25 2.26,1.885 1.844,1.135 false 1.333,1.813 1.542,1.229 false 0.26,0.219 0.573,0.417 0.313,0.198 10 false *a 1.906,0.427 2.365,0.625 0.458,0.198 10 false F80 2.125,1.896 2.583,2.094 0.458,0.198 10 false GND 1.135,1.833 1.75,2.031 0.615,0.198 10 false RDFG
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F80-38 (RDFG) - F80-14 (GND) Ignition switch ON, rear window defogger switch on Below 2.2 V
F80-38 (RDFG) - F80-14 (GND) Ignition switch ON, rear window defogger switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE))

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE))
a.

Disconnect the Y2*1 or X16*2 back door glass (rear window defogger wire) connector.


b.

Disconnect the 1C semiconductor pwr integration ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 (RDEF) - Y2-1*1 Always Below 1 Ω
1C-1 (RDEF) - X16-1*2 Always Below 1 Ω


*1: w/ Glass Hatch

*2: w/o Glass Hatch



Result:
Proceed to
OK
NG



OK

10.CHECK SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Reconnect the 1C semiconductor pwr integration ECU connector.


b.
B364259C03
0.552,0.365 0.896,0.604 0.344,0.24 2.333,0.365 2.677,0.604 0.344,0.24 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.604,0.396 0.896,0.594 0.292,0.198 10 false Y2 2.406,0.396 2.865,0.594 0.458,0.198 10 false X16 1,0.385 1.281,0.625 0.281,0.24 12 false *A 2.771,0.375 3.052,0.615 0.281,0.24 12 false *B
*A w/ Glass Hatch
*B w/o Glass Hatch
*a Front view of wire harness connector
(to Back Door Glass (Rear Window Defogger Wire))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y2-1 - Body ground*1 Ignition switch ON, rear window defogger switch on 11 to 14 V
Y2-1 - Body ground*1 Ignition switch ON, rear window defogger switch off Below 1 V
X16-1 - Body ground*2 Ignition switch ON, rear window defogger switch on 11 to 14 V
X16-1 - Body ground*2 Ignition switch ON, rear window defogger switch off Below 1 V


*1: w/ Glass Hatch


*2: w/o Glass Hatch



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE) - BODY GROUND)

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

11.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE) - BODY GROUND)
a.

Disconnect the Y2*1 or X17*2 back door glass (rear window defogger wire) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y2-2 - Body ground*1 Always Below 1 Ω
X17-1 - Body ground*2 Always Below 1 Ω


*1: w/ Glass Hatch


*2: w/o Glass Hatch



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR