Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.12–2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the downhill assist control (for AWD) or dynamic radar cruise control (w/ dynamic radar cruise control) operating signal from the skid control ECU (brake actuator assembly), the stop light control relay (STOP LP relay) contact turns on and the stop light comes on.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction Either of the following is detected:
1.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay (STOP LP relay) drive output (STPO) is ON, a signal has not been input to the STP terminal for 5 seconds or more.

2.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay (STOP LP relay) drive output (STPO) is OFF, the signal at the STP is different from the input signal at the STP2 for 5 seconds or more.


·

Wire harness or connector

·

Stop light switch assembly

·

Stop light control relay (STOP LP relay)

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When C1425 and/or C1426 is output together with C1380, inspect and repair the trouble areas indicated by C1425 and/or C1426 first.

for C1425: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425

for C1426: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

NG

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
C277402
0.156,0.958 0.573,1.26 0.417,0.302 2.427,1.885 2.208,1.229 true 0.26,1.031 0.719,1.229 0.458,0.198 10 false A47 0.198,0.208 0.51,0.406 0.313,0.198 10 false *a 2.292,1.885 2.813,2.083 0.521,0.198 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-22 (STP2) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
A47-22 (STP2) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT CONTROL RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT CONTROL RELAY)
a.

Reconnect the A47 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Select the Active Test using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (STOP LP relay) Relay ON/OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

e.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Stop light control relay (STOP LP relay) ON or OFF ON: Stop light control relay (STOP LP relay) on
OFF: Stop light control relay (STOP LP relay) off
w/ Downhill assist control or dynamic radar cruise control
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light Relay
50003 105 287

f.

Check the operating condition of the stop light control relay (STOP LP relay) when operating it using the GTS.


Result:
Result
OK
NG



OK

5.RECONFIRM DTC

NG

6.INSPECT STOP LIGHT CONTROL RELAY
5.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1380 is not output. A
DTC C1380 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

6.INSPECT STOP LIGHT CONTROL RELAY
a.
C223784
2.719,1.417 2.719,0.865 2.719,0.865 2.76,0.865 false 2.448,1.906 2.448,1.635 2.448,1.635 2.01,1.635 false 2.302,2.313 2.302,2.844 2.302,2.844 2.25,2.844 false 2.594,2.313 2.594,3.083 2.594,3.083 2.552,3.083 false 2.854,2.313 2.854,3.083 2.854,3.083 2.896,3.083 false 0.188,0.177 1.823,0.385 1.635,0.208 10 false *1 1.896,1.563 2.021,1.729 0.125,0.167 10 false 5 2.906,2.99 3.031,3.156 0.125,0.167 10 false 1 2.135,2.76 2.26,2.927 0.125,0.167 10 false 2 2.781,0.781 2.906,0.948 0.125,0.167 10 false 3 2.427,2.99 2.552,3.156 0.125,0.167 10 false 4
*1 Stop Light Control Relay (STOP LP Relay)


Turn the ignition switch off.


b.

Remove the stop light control relay (STOP LP relay).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 4 Voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (POWER SOURCE TERMINAL)

NG

REPLACE STOP LIGHT CONTROL RELAY

7.INSPECT ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (POWER SOURCE TERMINAL)
a.
C297286
0.188,0.177 0.5,0.375 0.313,0.198 10 false *1 1.302,0.25 1.615,0.448 0.313,0.198 10 false *2
*1 NO. 1 Engine Room Relay Block and NO. 1 Junction Block Assembly
*2 Stop Light Control Relay (STOP LP Relay)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Stop light control relay (STOP LP relay) terminal 5 - Body ground Always 11 to 14 V
Stop light control relay (STOP LP relay) terminal 2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)
a.

Install the stop light control relay (STOP LP relay).


b.
C277402
0.156,0.958 0.573,1.26 0.417,0.302 2.167,1.885 2.01,1.313 true 0.26,1.031 0.719,1.229 0.458,0.198 10 false A47 0.198,0.208 0.51,0.406 0.313,0.198 10 false *a 2.021,1.896 2.49,2.073 0.469,0.177 10 false STPO
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-31 (STPO) - Body ground Ignition switch ON 11 to 14 V


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C277402
0.156,0.958 0.573,1.26 0.417,0.302 1.448,0.958 1.26,0.354 true 0.26,1.031 0.719,1.229 0.458,0.198 10 false A47 0.198,0.208 0.51,0.406 0.313,0.198 10 false *a 1.115,0.198 1.427,0.396 0.313,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
A47-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)