Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.12–2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When IG1 terminal voltage is 9.5 V or more, an open in the stop light switch assembly input line continues for 0.3 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Stop light control relay (STOP LP relay) (w/ Downhill assist control or dynamic radar cruise control)

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C296497
4.958,1.958 4.958,1.448 false 2.115,0.479 2.271,0.677 0.156,0.198 10 false 1 0.802,0.479 0.958,0.677 0.156,0.198 10 false 2 2.521,0.5 2.833,0.781 0.313,0.281 10 false *1 4.49,0.5 4.792,0.833 0.302,0.333 10 false *1 5.719,0.479 6.104,0.865 0.385,0.385 10 false 22 5.979,0.594 6.646,0.854 0.667,0.26 10 false STP2*1 5.979,2.188 6.417,2.448 0.438,0.26 10 false STP 5.969,2.854 6.656,3.188 0.688,0.333 10 false STPO*1 5.969,3.479 6.479,3.823 0.51,0.344 10 false GND1 5.781,3.344 5.938,3.542 0.156,0.198 10 false 1 5.729,2.74 5.969,2.958 0.24,0.219 10 false 31 5.75,2.083 6.031,2.313 0.281,0.229 10 false 2 4.875,1.115 5.865,1.552 0.99,0.438 10 false Open Detection Area 4.115,4.448 5.438,4.823 1.323,0.375 10 false to Stop Light Circuit 4.083,2.75 4.333,3.073 0.25,0.323 10 false *1 4.063,2.094 4.313,2.354 0.25,0.26 10 false *1 3.656,2.083 3.896,2.333 0.24,0.25 10 false 3 3.656,2.729 3.813,2.927 0.156,0.198 10 false 1 2.969,1.667 3.125,1.865 0.156,0.198 10 false 4 2.521,2.073 2.792,2.365 0.271,0.292 10 false 5 2.521,2.729 2.698,2.99 0.177,0.26 10 false 2 2.438,3.25 3.958,3.729 1.521,0.479 10 false Stop Light Control Relay (STOP LP Relay)*1 2.24,4.073 3.875,4.365 1.635,0.292 10 false from IG1 NO. 3 Relay 1.531,3.969 1.708,4.229 0.177,0.26 10 false 1 1.135,3.969 1.313,4.229 0.177,0.26 10 false 2 1.542,4.563 2.698,4.854 1.156,0.292 10 false from Battery 0.917,4.458 1.094,4.719 0.177,0.26 10 false 1 0.542,4.458 0.719,4.719 0.177,0.26 10 false 2 1.479,2.75 1.781,3.104 0.302,0.354 10 false *1 1.458,2.094 1.792,2.427 0.333,0.333 10 false *1 0.75,1.052 1.156,1.333 0.406,0.281 10 false A54 1.094,1.052 2.229,1.51 1.135,0.458 10 false Stop Light Switch Assembly 5.563,4.854 5.938,5.125 0.375,0.271 10 false A47 5.563,5.042 7.146,5.469 1.583,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 3.135,1.333 3.292,1.531 0.156,0.198 10 false *1 3.802,0.906 4.031,1.115 0.229,0.208 10 false *2 0.583,4.771 1.74,5.063 1.156,0.292 10 false STOP 1.083,4.24 2.24,4.531 1.156,0.292 10 false IG1 NO. 2 1.146,5.094 5.26,5.448 4.115,0.354 10 false *1: w/ Downhill Assist Control or Dynamic Radar Cruise Control 1.156,5.458 5.656,5.771 4.5,0.313 10 false *2: w/o Downhill Assist Control or Dynamic Radar Cruise Control

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C277402
0.156,0.958 0.573,1.26 0.417,0.302 1.448,0.958 1.26,0.354 true 0.26,1.031 0.719,1.229 0.458,0.198 10 false A47 0.198,0.208 0.51,0.406 0.313,0.198 10 false *a 1.115,0.198 1.427,0.396 0.313,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
A47-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Result Proceed to
OK (w/ Downhill assist control or dynamic radar cruise control) A
OK (w/o Downhill assist control or dynamic radar cruise control) B
NG C



A

6.CHECK HARNESS AND CONNECTOR (SWITCH INPUT TERMINAL)

B

10.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

C

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (SWITCH INPUT TERMINAL)
a.
C297286
0.188,0.177 0.5,0.375 0.313,0.198 10 false *1 1.302,0.25 1.615,0.448 0.313,0.198 10 false *2
*1 NO. 1 Engine Room Relay Block and NO. 1 Junction Block Assembly
*2 Stop Light Control Relay (STOP LP Relay)


Turn the ignition switch off.


b.

Remove the stop light control relay (STOP LP relay).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Stop light control relay (STOP LP relay) terminal 4 - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
Stop light control relay (STOP LP relay) terminal 4 - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

7.INSPECT STOP LIGHT CONTROL RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SWITCH INPUT CIRCUIT)

7.INSPECT STOP LIGHT CONTROL RELAY
a.
C223784
2.719,1.417 2.719,0.865 2.719,0.865 2.76,0.865 false 2.448,1.906 2.448,1.635 2.448,1.635 2.01,1.635 false 2.302,2.313 2.302,2.844 2.302,2.844 2.25,2.844 false 2.594,2.313 2.594,3.083 2.594,3.083 2.552,3.083 false 2.854,2.313 2.854,3.083 2.854,3.083 2.896,3.083 false 0.188,0.177 1.823,0.385 1.635,0.208 10 false *1 1.896,1.563 2.021,1.729 0.125,0.167 10 false 5 2.906,2.99 3.031,3.156 0.125,0.167 10 false 1 2.135,2.76 2.26,2.927 0.125,0.167 10 false 2 2.781,0.781 2.906,0.948 0.125,0.167 10 false 3 2.427,2.99 2.552,3.156 0.125,0.167 10 false 4
*1 Stop Light Control Relay (STOP LP Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 4 Voltage is applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT CONTROL RELAY

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C277402
0.156,0.958 0.573,1.26 0.417,0.302 1.448,0.958 1.26,0.354 true 0.26,1.031 0.719,1.229 0.458,0.198 10 false A47 0.198,0.208 0.51,0.406 0.313,0.198 10 false *a 1.115,0.198 1.427,0.396 0.313,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Install the stop light control relay (STOP LP relay).


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
A47-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

9.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A47 skid control ECU (brake actuator assembly) connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Depress the brake pedal several times to test the stop light circuit.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:
·

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE





A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

10.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C277402
0.156,0.958 0.573,1.26 0.417,0.302 1.448,0.958 1.26,0.354 true 0.26,1.031 0.719,1.229 0.458,0.198 10 false A47 0.198,0.208 0.51,0.406 0.313,0.198 10 false *a 1.115,0.198 1.427,0.396 0.313,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
A47-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

11.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A47 skid control ECU (brake actuator assembly) connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Depress the brake pedal several times to test the stop light circuit.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:
·

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE





A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)