Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › AIR FUEL RATIO SENSOR › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0106873 AIR FUEL RATIO SENSOR A

2GR-FE ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A315093C01
1.115,0.531 1.563,0.469 1.563,0.469 1.302,2.104 false 0.719,1.042 1.031,1.198 0.313,0.156 10 false *a 2.135,1.104 2.448,1.26 0.313,0.156 10 false *b 1.573,0.313 2.031,0.51 0.458,0.198 10 false SST
*a Length of SST 30 mm (1.18 in.)
*b Length of Torque Wrench 260 mm (10.2 in.)


Using SST, install the air fuel ratio sensor to the exhaust manifold sub-assembly RH.

SST
09224-00010  

Torque:
without SST [Torque (N*m (kgf*cm, ft.*lbf))] : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))] : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).

·

The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).

·

If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 17104 2.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 89467B 4.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A315094C01
0.958,2.521 1.521,3.073 1.521,3.073 1.948,2.563 true 0.625,2.844 0.875,3.042 0.25,0.198 10 true *a 1.49,0.094 1.667,0.271 0.177,0.177 10 true *b 1.385,3.115 1.688,3.313 0.302,0.198 10 true SST
*a Length of SST 30 mm (1.18 in.)
*b Length of Torque Wrench 260 mm (10.2 in.)


Using SST, install the air fuel ratio sensor to the exhaust manifold sub-assembly LH.

SST
09224-00010  

Torque:
without SST [Torque (N*m (kgf*cm, ft.*lbf))] : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))] : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).

·

The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).

·

If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




b.

Connect the air fuel ratio sensor connector.


c.

Engage the wire harness clamp.


Hide 6.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION