Home › Engine / Hybrid System › 2GR-FE (INTAKE / EXHAUST) › EXHAUST PIPE › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019666 2GR-FE INTAKE / EXHAUST _0109814 EXHAUST PIPE A

2GR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Install the front exhaust pipe assembly to the exhaust manifold sub-assembly LH (TWC: Front Catalyst) with the 2 nuts.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


Hide 17584B 2.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

a.

Install the No. 1 exhaust pipe support bracket with the 2 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 17403 3.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

a.

Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.


b.

Install the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 nuts.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


Hide 89465 4.INSTALL HEATED OXYGEN SENSOR (for Bank 2)

Hide 89465 5.INSTALL HEATED OXYGEN SENSOR (for Bank 1)

Hide 17420 6.INSTALL CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.5 mm (1.63 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front No. 3 exhaust pipe sub-assembly.


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front No. 3 Exhaust Pipe Sub-assembly
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the center exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust pipe support.


e.

Install the center exhaust pipe assembly (TWC: Rear Catalyst) to the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C28
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.719,0.323 0.875,0.469 0.156,0.146 10 false *1 0.76,1.427 0.917,1.573 0.156,0.146 10 false *2 2.844,0.365 3,0.51 0.156,0.146 10 false *3 0.625,1.74 0.823,2 0.198,0.26 10 false *a
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Front No. 3 Exhaust Pipe Sub-assembly
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the center exhaust pipe assembly (TWC: Rear Catalyst) and front No. 3 exhaust pipe sub-assembly is consistent front-to-rear and left-to-right.



Hide 17430 7.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the center exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the tail exhaust pipe assembly to the 4 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly to the center exhaust pipe assembly (TWC: Rear Catalyst) with the 2 bolts.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


Hide 9.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform "Inspection After Repair" after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION