Home › Engine / Hybrid System › 2GR-FE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019666 2GR-FE INTAKE / EXHAUST _0109813 EXHAUST MANIFOLD A

2GR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17173A 1.INSTALL EXHAUST MANIFOLD TO HEAD GASKET LH

a.

Install a new exhaust manifold to head gasket LH to the cylinder head sub-assembly.


Hide 89467B 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

Hide 17105 3.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst).

a.

Temporarily install the exhaust manifold sub-assembly LH (TWC: Front Catalyst) with the 6 nuts.


b.
A197637N02
2.323,0.042 2.479,0.208 0.156,0.167 10 true 1 2.927,0.375 3.104,0.552 0.177,0.177 10 true 6 1.5,1.542 1.656,1.719 0.156,0.177 10 true 2 1.896,1.552 2.063,1.75 0.167,0.198 10 true 3 0.906,0.042 1.073,0.219 0.167,0.177 10 true 4 0.615,1.521 0.781,1.708 0.167,0.188 10 true 5

Using a 12 mm deep socket wrench, tighten the 6 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17119 4.INSTALL NO. 2 MANIFOLD STAY

a.
A140783N03
1.979,0.219 2.177,0.417 0.198,0.198 10 true 1 2.146,1.594 2.344,1.802 0.198,0.208 10 true 2

Install the No. 2 manifold stay to the exhaust manifold sub-assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut in the order shown in the illustration.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 17168 5.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold sub-assembly LH (TWC: Front Catalyst) with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 12142 6.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Install the front exhaust pipe assembly to the exhaust manifold sub-assembly LH (TWC: Front Catalyst) with the 2 nuts.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


c.

Connect the heated oxygen sensor (for Bank 2) connector.


d.

Engage the 3 wire harnesses clamps.


Hide 17584B 9.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

a.

Install the No. 1 exhaust pipe support bracket with the 2 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 17173 10.INSTALL EXHAUST MANIFOLD TO HEAD GASKET

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


Hide 17104 11.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst)

a.

Using a 12 mm deep socket wrench, install the exhaust manifold sub-assembly RH (TWC: Front Catalyst) with the 6 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Engage the wire harness clamp.


c.

Connect the air fuel ratio sensor (for Bank 1) connector.


Hide 17118 12.INSTALL MANIFOLD STAY

a.

Install the manifold stay to the exhaust manifold sub-assembly RH (TWC: Front Catalyst) and automatic transaxle assembly with bolt and nut.

Torque:
Bolt : 34 N*m (347 kgf*cm, 25 ft.*lbf)
Nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 17403 13.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.5 mm (1.63 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front No. 3 exhaust pipe sub-assembly (center exhaust pipe assembly (TWC: Rear Catalyst) side).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front No. 3 Exhaust Pipe Sub-assembly
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.


e.

Temporarily install the front No. 3 exhaust pipe sub-assembly with the 4 bolts, 2 nuts and 2 compression springs.


f.

Tighten the 2 bolts and 2 nuts.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


g.

Tighten the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C27
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.708,0.354 1.021,0.656 0.313,0.302 10 false *1 0.74,1.448 0.99,1.698 0.25,0.25 10 false *2 2.875,0.385 3.219,0.677 0.344,0.292 10 false *3 0.625,1.74 1,2.01 0.375,0.271 10 false *a
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Front No. 3 Exhaust Pipe Sub-assembly
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the center exhaust pipe assembly (TWC: Rear Catalyst) and front No. 3 exhaust pipe sub-assembly is consistent front-to-rear and left-to-right.



h.

Connect the heated oxygen sensor (for Bank 1) connector.


i.

Engage the 4 wire harness clamps.


Hide 37100 14.TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

Hide 37100 15.FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

Hide 58166 16.INSTALL FRONT FLOOR COVER LH

a.
A315837C01
1.521,1.313 1.74,1.542 0.219,0.229 10 true A 1.552,0.635 1.771,0.865 0.219,0.229 10 true B 0.781,0.542 1,0.771 0.219,0.229 10 true B
V100135

Bolt
V100136

Screw


Install the front floor cover LH with the 2 clips (B).


b.

Install the clip (A), 2 screws and 4 bolts to the front floor cover LH.


Hide 51442 17.INSTALL NO. 2 ENGINE UNDER COVER

Hide 16400 18.INSTALL RADIATOR ASSEMBLY