Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › HEATED OXYGEN SENSOR › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0106874 HEATED OXYGEN SENSOR A

2GR-FE ENGINE CONTROL  HEATED OXYGEN SENSOR  INSTALLATION  


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 1)

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A315102C01
1.344,2.042 0.854,0.698 0.854,0.698 1.552,0.698 true 1.854,0.938 2.167,1.094 0.313,0.156 10 false *a 0.698,2.333 0.875,2.521 0.177,0.188 10 true *b 0.51,0.583 0.833,0.76 0.323,0.177 10 true SST
*a Length of SST 30 mm (1.18 in.)
*b Length of Torque Wrench 260 mm (10.2 in.)


Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

SST
09224-00010  

Torque:
without SST [Torque (N*m (kgf*cm, ft.*lbf))] : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))] : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

If the heated oxygen sensor has been struck or dropped, replace it.


HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).

·

The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).

·

If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




b.

Install the wire harness clamp bracket to the heated oxygen sensor.


c.

Connect the heated oxygen sensor connector.


d.

Engage the 4 wire harness clamps.


Hide 89465 3.INSTALL HEATED OXYGEN SENSOR (for Bank 2)

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A315098C01
1.875,1.094 2.229,1.563 2.229,1.563 2.5,0.646 true 2.792,0.865 2.99,1.063 0.198,0.198 10 false *a 0.521,0.698 0.708,0.865 0.188,0.167 10 true *b 2.135,1.625 2.479,1.823 0.344,0.198 10 true SST
*a Length of SST 30 mm (1.18 in.)
*b Length of Torque Wrench 260 mm (10.2 in.)


Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

SST
09224-00010  

Torque:
without SST [Torque (N*m (kgf*cm, ft.*lbf))] : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))] : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

If the heated oxygen sensor has been struck or dropped, replace it.


HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).

·

The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).

·

If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




b.

Connect the heated oxygen sensor connector.


c.

Engage the 3 wire harness clamps.


Hide 5.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION