Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM3160E _58 Vehicle Interior _019712 SEAT _0107153 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch (driver door) signals from the outer mirror control ECU assembly (driver door) via CAN communication. If the seat memory SET switch is being pressed when one of the M1 or M2 switches is pressed, or if one of the M1 or M2 switches is pressed within 3 seconds of pressing the seat memory SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the position control ECU and switch assembly. After receiving the request signal, the position control ECU and switch assembly memorizes the location data of each motor.

WIRING DIAGRAM

B276669E05
3.49,2.24 3.813,2.385 0.323,0.146 10 false GND 3.271,2.688 4.198,2.948 0.927,0.26 10 false I2*1, H2*2 4.406,0.313 4.635,0.458 0.229,0.146 10 false M1 4.698,0.229 4.927,0.375 0.229,0.146 10 false 2 4.698,0.896 4.927,1.042 0.229,0.146 10 false 3 4.698,1.542 4.927,1.688 0.229,0.146 10 false 1 3.302,2.125 3.479,2.271 0.177,0.146 10 false 7 5.365,0.229 5.531,0.375 0.167,0.146 10 false 4 5.365,0.896 5.531,1.042 0.167,0.146 10 false 3 5.365,1.542 5.531,1.688 0.167,0.146 10 false 8 5.365,2.135 5.531,2.281 0.167,0.146 10 false 2 5.521,0.188 6.219,0.469 0.698,0.281 10 false 1*1, M1*2 5.531,0.854 6.219,1.167 0.688,0.313 10 false 2*1, M2*2 5.531,1.385 6.125,1.708 0.594,0.323 10 false MMRY*1, MRY*2 5.552,2.135 5.719,2.281 0.167,0.146 10 false E 4.406,0.979 4.635,1.125 0.229,0.146 10 false M2 4.354,1.635 4.625,1.781 0.271,0.146 10 false MM 0.135,1.073 1.729,1.5 1.594,0.427 10 false Position Control ECU and Switch Assembly 0.135,2.698 1.781,3.073 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 3.26,2.854 4.865,3.229 1.604,0.375 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.563,2.708 6.781,3.115 1.219,0.406 10 false I11*1, H12*2 5.563,2.854 6.885,3.208 1.323,0.354 10 false Seat Memory Switch (Driver Door) 0.719,3.458 2.469,3.635 1.75,0.177 10 false : CAN Communication Line 2.042,2.823 2.969,3.083 0.927,0.26 10 false *1: for LHD 2.042,3.135 2.969,3.396 0.927,0.26 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 of the seat memory switches are pressed simultaneously.

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the position control ECU and switch assembly.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SEAT MEMORY SWITCH (DRIVER DOOR))

NG

2.READ VALUE USING GTS (SEAT MEMORY SWITCH (DRIVER DOOR))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Mirror L*1 or Mirror R*2 / Data List.

*1: for LHD

*2: for RHD



e.

Read the Data List according to the display on the GTS.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 M1 switch ON or OFF ON: M1 switch on
OFF: M1 switch off
-
Seat Memory Switch2 M2 switch ON or OFF ON: M2 switch on
OFF: M2 switch off
-
Seat Memory Set SW SET switch ON or OFF ON: SET switch on
OFF: SET switch off
-
Body Electrical > Mirror L > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Set SW
50003 225 1,2,4
Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 M1 switch ON or OFF ON: M1 switch on
OFF: M1 switch off
-
Seat Memory Switch2 M2 switch ON or OFF ON: M2 switch on
OFF: M2 switch off
-
Seat Memory Set SW SET switch ON or OFF ON: SET switch on
OFF: SET switch off
-
Body Electrical > Mirror R > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Set SW
50003 224 1,2,4
OK:

ON or OFF is displayed on the GTS according to the table above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (BUZZER)

NG

8.INSPECT SEAT MEMORY SWITCH (DRIVER DOOR)
3.PERFORM ACTIVE TEST USING GTS (BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

Buzzer sounds normally.



Result:
Proceed to
OK
NG



OK

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)
a.

Temporarily replace the outer mirror control ECU assembly (driver door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
5.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check that the seat position memory and restoring function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring function operate normally.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

6.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
6.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check that the seat position memory and restoring function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring function operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

8.INSPECT SEAT MEMORY SWITCH (DRIVER DOOR)
a.

Remove the seat memory switch (driver door).

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Inspect the seat memory switch (driver door).

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - SEAT MEMORY SWITCH (DRIVER DOOR) - BODY GROUND)

NG

REPLACE SEAT MEMORY SWITCH (DRIVER DOOR)

9.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - SEAT MEMORY SWITCH (DRIVER DOOR) - BODY GROUND)
a.

Disconnect the I2*1 or H2*2 outer mirror control ECU assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I2-1 (MM) - I11-8 (MMRY) Always Below 1 Ω
I2-1 (MM) or I11-8 (MMRY) - Body ground Always 10 kΩ or higher
I2-2 (M1) - I11-4 (1) Always Below 1 Ω
I2-2 (M1) or I11-4 (1) - Body ground Always 10 kΩ or higher
I2-3 (M2) - I11-3 (2) Always Below 1 Ω
I2-3 (M2) or I11-3 (2) - Body ground Always 10 kΩ or higher
I2-7 (GND) - Body ground Always Below 1 Ω
I11-2 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
H2-1 (MM) - H12-8 (MRY) Always Below 1 Ω
H2-1 (MM) or H12-8 (MRY) - Body ground Always 10 kΩ or higher
H2-2 (M1) - H12-4 (M1) Always Below 1 Ω
H2-2 (M1) or H12-4 (M1) - Body ground Always 10 kΩ or higher
H2-3 (M2) - H12-3 (M2) Always Below 1 Ω
H2-3 (M2) or H12-3 (M2) - Body ground Always 10 kΩ or higher
H2-7 (GND) - Body ground Always Below 1 Ω
H12-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR