Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0100809 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator (clock assembly).

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger airbag assembly and front seat airbag sub-assembly RH.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the passenger airbag ON/OFF indicator circuit.

·

Passenger airbag ON/OFF indicator malfunction

·

Airbag sensor assembly malfunction


·

No. 4 instrument panel wire

·

Instrument panel wire

·

Instrument panel junction block assembly

·

Passenger airbag ON/OFF indicator (Clock assembly)

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C295811E01
5.302,4.563 5.76,4.76 0.458,0.198 10 false F38 5.302,4.729 6.885,5.26 1.583,0.531 10 false Airbag Sensor Assembly 5.458,0.906 6.01,1.167 0.552,0.26 10 false PAON 5.458,1.896 6.01,2.156 0.552,0.26 10 false P-AB 5.458,3.271 6.01,3.531 0.552,0.26 10 false E1 5.5,4.052 6.052,4.313 0.552,0.26 10 false E2 5.24,0.802 5.771,1.135 0.531,0.333 10 false 23 5.219,1.802 5.75,2.104 0.531,0.302 10 false 17 5.229,3.156 5.781,3.417 0.552,0.26 10 false 25 5.229,3.927 5.781,4.188 0.552,0.26 10 false 26 3.646,2.01 4.198,2.271 0.552,0.26 10 false 4A 3.646,2.156 5.25,2.677 1.604,0.521 10 false Instrument Panel Junction Block Assembly 1.302,0.885 1.854,1.146 0.552,0.26 10 false PAON 1.365,1.885 1.917,2.146 0.552,0.26 10 false P-AB 1.469,3.26 2.021,3.521 0.552,0.26 10 false IG+ 2.063,3.427 3,3.688 0.938,0.26 10 false IG1 NO. 3 2.448,4.031 3.813,4.344 1.365,0.313 10 false from IG1 NO. 3 Relay 2.677,0.896 3.229,1.156 0.552,0.26 10 false GF1 2.677,1.896 3.229,2.156 0.552,0.26 10 false GF1 0.208,4.563 0.667,4.76 0.458,0.198 10 false G7 0.208,4.729 2.479,5.313 2.271,0.583 10 false Passenger Airbag ON/OFF Indicator (Clock Assembly) 4.583,0.802 5.125,1.021 0.542,0.219 10 false 25 4.583,1.802 5.125,2.063 0.542,0.26 10 false 26 3.906,0.802 4.438,1.135 0.531,0.333 10 false 23 3.906,1.802 4.458,2.031 0.552,0.229 10 false 44 2.771,0.698 3.302,1.031 0.531,0.333 10 false 2 2.771,1.698 3.302,2.031 0.531,0.333 10 false 1 1.76,3.167 2.292,3.5 0.531,0.333 10 false 1 1.76,0.802 2.292,1.135 0.531,0.333 10 false 16 1.76,1.802 2.292,2.135 0.531,0.333 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM



Result:
Result Proceed to
ON/OFF Indicator illumination is always "ON". A
ON/OFF Indicator illumination is always "OFF". B



A

2.CHECK CONNECTORS

B

17.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, clock assembly and instrument panel junction block assembly. Also check that the connectors that link the No. 4 instrument panel wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, clock assembly and instrument panel junction block assembly. Also disconnect the connectors that link the No. 4 instrument panel wire and instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.

Connect the connector to the clock assembly and instrument panel junction block assembly. Also connect the connectors that link the No. 4 instrument panel wire and instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK WIRE HARNESS (OPEN)
4.CHECK DTC
a.
C295810C01
2.615,0.771 2.927,0.927 0.313,0.156 10 false A 1.323,1.49 1.635,1.646 0.313,0.156 10 false F 0.729,1.49 1.042,1.646 0.313,0.156 10 false G 0.281,0.802 0.604,1.031 0.323,0.229 10 false *1 2.917,0.771 3.292,1.083 0.375,0.313 10 false *2 0.302,1.49 0.729,1.813 0.427,0.323 10 false *3 2.427,0.771 2.74,0.927 0.313,0.156 10 false B 0.74,0.802 1.052,0.958 0.313,0.156 10 false C 0.552,0.802 0.865,0.958 0.313,0.156 10 false D 1.51,1.49 1.823,1.646 0.313,0.156 10 false E 0.552,1.49 0.865,1.646 0.313,0.156 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the connector to the airbag sensor assembly.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK WIRE HARNESS (OPEN)
a.
C295808C01
0.333,0.427 0.667,0.656 0.333,0.229 0.302,3.708 0.635,3.938 0.333,0.229 1.531,1.427 1.531,1.177 false 0.865,1.24 1.271,0.833 false 2.167,1.25 1.719,0.604 false 1.323,4.344 1.708,3.979 false 2.198,4.344 1.823,3.979 false 0.188,2 0.563,2.271 0.375,0.271 10 false *1 3.01,2.01 3.323,2.344 0.313,0.333 10 false *2 0.208,2.677 0.646,3.073 0.438,0.396 10 false *3 1.458,1.448 1.896,1.792 0.438,0.344 10 false *4 0.156,0.125 0.594,0.583 0.438,0.458 10 false *a 0.135,3.271 0.552,3.635 0.417,0.365 10 false *b 0.385,0.458 0.76,0.729 0.375,0.271 10 false F38 0.667,1.25 1.25,1.5 0.583,0.25 10 false PAON 2.021,1.25 2.604,1.5 0.583,0.25 10 false P-AB 2.021,4.333 2.604,4.583 0.583,0.25 10 false PAON 1.177,4.333 1.76,4.583 0.583,0.25 10 false P-AB 0.385,3.74 0.76,4.01 0.375,0.271 10 false G7 2.698,2.01 3.01,2.344 0.313,0.333 10 false A 2.323,2.01 2.635,2.344 0.313,0.333 10 false B 0.625,2.01 0.938,2.344 0.313,0.333 10 false C 0.448,2.01 0.76,2.344 0.313,0.333 10 false D 1.563,2.677 1.875,3.01 0.313,0.333 10 false E 1.375,2.677 1.688,3.01 0.313,0.333 10 false F 0.813,2.677 1.125,3.01 0.313,0.333 10 false G 0.448,2.677 0.76,3.01 0.313,0.333 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Clock Assembly)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the clock assembly.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

6.CHECK WIRE HARNESS (SHORT)

NG

15.CHECK NO. 4 INSTRUMENT PANEL WIRE (OPEN)
6.CHECK WIRE HARNESS (SHORT)
a.
C295809C01
0.333,2.396 0.656,2.615 0.323,0.219 1.417,2.99 1.719,2.646 false 2.167,2.979 1.844,2.646 false 0.177,0.51 0.5,0.719 0.323,0.208 10 false *1 2.99,0.531 3.313,0.802 0.323,0.271 10 false *2 0.177,1.198 0.615,1.542 0.438,0.344 10 false *3 2.698,0.521 3,0.823 0.302,0.302 10 false A 0.177,1.854 0.573,2.177 0.396,0.323 10 false *a 2.323,0.521 2.635,0.823 0.313,0.302 10 false B 0.635,0.531 0.948,0.833 0.313,0.302 10 false C 0.448,0.531 0.76,0.833 0.313,0.302 10 false D 1.521,1.208 1.833,1.51 0.313,0.302 10 false E 1.333,1.208 1.646,1.51 0.313,0.302 10 false F 0.823,1.208 1.135,1.51 0.313,0.302 10 false G 0.448,1.208 0.76,1.51 0.313,0.302 10 false H 0.406,2.417 0.802,2.74 0.396,0.323 10 false G7 2,3 2.5,3.323 0.5,0.323 10 false PAON 1.25,3 1.792,3.333 0.542,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Clock Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS (SHORT TO B+)

NG

13.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT)
7.CHECK WIRE HARNESS (SHORT TO B+)
a.
C295809C01
0.333,2.396 0.656,2.615 0.323,0.219 1.417,2.99 1.719,2.646 false 2.167,2.979 1.844,2.646 false 0.177,0.51 0.5,0.719 0.323,0.208 10 false *1 2.99,0.531 3.313,0.802 0.323,0.271 10 false *2 0.177,1.198 0.615,1.542 0.438,0.344 10 false *3 2.698,0.521 3,0.823 0.302,0.302 10 false A 0.177,1.854 0.573,2.177 0.396,0.323 10 false *a 2.323,0.521 2.635,0.823 0.313,0.302 10 false B 0.635,0.531 0.948,0.833 0.313,0.302 10 false C 0.448,0.531 0.76,0.833 0.313,0.302 10 false D 1.521,1.208 1.833,1.51 0.313,0.302 10 false E 1.333,1.208 1.646,1.51 0.313,0.302 10 false F 0.823,1.208 1.135,1.51 0.313,0.302 10 false G 0.448,1.208 0.76,1.51 0.313,0.302 10 false H 0.406,2.417 0.802,2.74 0.396,0.323 10 false G7 2,3 2.5,3.323 0.5,0.323 10 false PAON 1.25,3 1.792,3.333 0.542,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Clock Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Ignition switch ON Below 1 V
G7-15 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

8.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

11.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO B+)
8.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C295809C01
0.333,2.396 0.656,2.615 0.323,0.219 1.417,2.99 1.719,2.646 false 2.167,2.979 1.844,2.646 false 0.177,0.51 0.5,0.719 0.323,0.208 10 false *1 2.99,0.531 3.313,0.802 0.323,0.271 10 false *2 0.177,1.198 0.615,1.542 0.438,0.344 10 false *3 2.698,0.521 3,0.823 0.302,0.302 10 false A 0.177,1.854 0.573,2.177 0.396,0.323 10 false *a 2.323,0.521 2.635,0.823 0.313,0.302 10 false B 0.635,0.531 0.948,0.833 0.313,0.302 10 false C 0.448,0.531 0.76,0.833 0.313,0.302 10 false D 1.521,1.208 1.833,1.51 0.313,0.302 10 false E 1.333,1.208 1.646,1.51 0.313,0.302 10 false F 0.823,1.208 1.135,1.51 0.313,0.302 10 false G 0.448,1.208 0.76,1.51 0.313,0.302 10 false H 0.406,2.417 0.802,2.74 0.396,0.323 10 false G7 2,3 2.5,3.323 0.5,0.323 10 false PAON 1.25,3 1.792,3.333 0.542,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Clock Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Always 1 MΩ or higher
G7-15 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

9.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO GROUND)
9.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C295807C01
0.292,2.396 0.635,2.615 0.344,0.219 1.479,0.542 1.479,0.125 1.479,0.125 1.229,0.125 false 1.063,1.26 1.063,0.927 1.063,0.927 0.813,0.927 false 1.5,3.063 1.719,2.635 false 2.104,3.052 1.823,2.635 false 0.177,0.51 0.552,0.833 0.375,0.323 10 false *1 3.01,0.542 3.271,0.927 0.26,0.385 10 false *2 0.188,1.198 0.646,1.635 0.458,0.438 10 false *3 1.083,0.042 1.469,0.292 0.385,0.25 10 false *4 0.156,1.865 0.49,2.344 0.333,0.479 10 false *a 0.646,0.844 1.042,1.094 0.396,0.25 10 false *5 0.375,2.427 0.833,2.865 0.458,0.438 10 false G7 1.938,3.083 2.594,3.333 0.656,0.25 10 false PAON 1.323,3.083 1.823,3.333 0.5,0.25 10 false P-AB 2.698,0.521 2.958,0.906 0.26,0.385 10 false A 2.323,0.521 2.583,0.906 0.26,0.385 10 false B 0.635,0.521 0.896,0.906 0.26,0.385 10 false C 0.448,0.521 0.708,0.906 0.26,0.385 10 false D 1.604,1.198 1.865,1.583 0.26,0.385 10 false E 1.229,1.208 1.49,1.594 0.26,0.385 10 false F 0.823,1.208 1.083,1.594 0.26,0.385 10 false G 0.438,1.208 0.698,1.594 0.26,0.385 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Always 1 MΩ or higher
G7-15 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C295806C01
1.5,0.219 1.813,0.438 0.313,0.219 1.615,2.385 1.615,2.052 1.615,2.052 1.865,2.052 false 1.063,3.031 1.063,2.74 1.063,2.74 0.896,2.74 false 0.938,1.573 1.385,1.135 false 2.948,1.594 1.927,1.01 false 2.417,1.594 1.823,1.01 false 1.802,1.583 1.396,1.01 false 0.198,2.375 0.583,2.635 0.385,0.26 10 false *1 3.01,2.385 3.365,2.75 0.354,0.365 10 false *2 0.188,2.969 0.563,3.302 0.375,0.333 10 false *3 1.906,1.979 2.26,2.323 0.354,0.344 10 false *4 0.75,2.667 1.063,2.906 0.313,0.24 10 false *5 0.135,0.167 0.51,0.469 0.375,0.302 10 false *a 2.698,2.385 3.052,2.75 0.354,0.365 10 false A 2.323,2.385 2.677,2.75 0.354,0.365 10 false B 0.823,2.375 1.177,2.74 0.354,0.365 10 false C 0.448,2.375 0.802,2.74 0.354,0.365 10 false D 1.594,2.979 1.948,3.344 0.354,0.365 10 false E 1.229,2.979 1.583,3.344 0.354,0.365 10 false F 0.823,2.979 1.177,3.344 0.354,0.365 10 false G 0.448,2.979 0.802,3.344 0.354,0.365 10 false H 1.625,1.583 2.146,1.917 0.521,0.333 10 false PAON 2.24,1.583 2.76,1.917 0.521,0.333 10 false PAON 0.76,1.583 1.281,1.917 0.521,0.333 10 false P-AB 2.802,1.583 3.323,1.917 0.521,0.333 10 false P-AB 1.583,0.25 2.104,0.583 0.521,0.333 10 false 4A
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - Body ground Always 1 MΩ or higher
4A-23 (PAON) - Body ground Always 1 MΩ or higher
4A-26 (P-AB) - Body ground Always 1 MΩ or higher
4A-44 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C295807C01
0.292,2.396 0.635,2.615 0.344,0.219 1.479,0.542 1.479,0.125 1.479,0.125 1.229,0.125 false 1.063,1.26 1.063,0.927 1.063,0.927 0.813,0.927 false 1.5,3.063 1.719,2.635 false 2.104,3.052 1.823,2.635 false 0.177,0.51 0.552,0.833 0.375,0.323 10 false *1 3.01,0.542 3.271,0.927 0.26,0.385 10 false *2 0.188,1.198 0.646,1.635 0.458,0.438 10 false *3 1.083,0.042 1.469,0.292 0.385,0.25 10 false *4 0.156,1.865 0.49,2.344 0.333,0.479 10 false *a 0.646,0.844 1.042,1.094 0.396,0.25 10 false *5 0.375,2.427 0.833,2.865 0.458,0.438 10 false G7 1.938,3.083 2.594,3.333 0.656,0.25 10 false PAON 1.323,3.083 1.823,3.333 0.5,0.25 10 false P-AB 2.698,0.521 2.958,0.906 0.26,0.385 10 false A 2.323,0.521 2.583,0.906 0.26,0.385 10 false B 0.635,0.521 0.896,0.906 0.26,0.385 10 false C 0.448,0.521 0.708,0.906 0.26,0.385 10 false D 1.604,1.198 1.865,1.583 0.26,0.385 10 false E 1.229,1.208 1.49,1.594 0.26,0.385 10 false F 0.823,1.208 1.083,1.594 0.26,0.385 10 false G 0.438,1.208 0.698,1.594 0.26,0.385 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Ignition switch ON Below 1 V
G7-15 (P-AB) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

12.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

12.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C295806C01
1.5,0.219 1.813,0.438 0.313,0.219 1.615,2.385 1.615,2.052 1.615,2.052 1.865,2.052 false 1.063,3.031 1.063,2.74 1.063,2.74 0.896,2.74 false 0.938,1.573 1.385,1.135 false 2.948,1.594 1.927,1.01 false 2.417,1.594 1.823,1.01 false 1.802,1.583 1.396,1.01 false 0.198,2.375 0.583,2.635 0.385,0.26 10 false *1 3.01,2.385 3.365,2.75 0.354,0.365 10 false *2 0.188,2.969 0.563,3.302 0.375,0.333 10 false *3 1.906,1.979 2.26,2.323 0.354,0.344 10 false *4 0.75,2.667 1.063,2.906 0.313,0.24 10 false *5 0.135,0.167 0.51,0.469 0.375,0.302 10 false *a 2.698,2.385 3.052,2.75 0.354,0.365 10 false A 2.323,2.385 2.677,2.75 0.354,0.365 10 false B 0.823,2.375 1.177,2.74 0.354,0.365 10 false C 0.448,2.375 0.802,2.74 0.354,0.365 10 false D 1.594,2.979 1.948,3.344 0.354,0.365 10 false E 1.229,2.979 1.583,3.344 0.354,0.365 10 false F 0.823,2.979 1.177,3.344 0.354,0.365 10 false G 0.448,2.979 0.802,3.344 0.354,0.365 10 false H 1.625,1.583 2.146,1.917 0.521,0.333 10 false PAON 2.24,1.583 2.76,1.917 0.521,0.333 10 false PAON 0.76,1.583 1.281,1.917 0.521,0.333 10 false P-AB 2.802,1.583 3.323,1.917 0.521,0.333 10 false P-AB 1.583,0.25 2.104,0.583 0.521,0.333 10 false 4A
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - Other terminals Always 1 MΩ or higher
4A-23 (PAON) - Other terminals Always 1 MΩ or higher
4A-26 (P-AB) - Other terminals Always 1 MΩ or higher
4A-44 (P-AB) - Other terminals Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT)
a.
C295807C01
0.292,2.396 0.635,2.615 0.344,0.219 1.479,0.542 1.479,0.125 1.479,0.125 1.229,0.125 false 1.063,1.26 1.063,0.927 1.063,0.927 0.813,0.927 false 1.5,3.063 1.719,2.635 false 2.104,3.052 1.823,2.635 false 0.177,0.51 0.552,0.833 0.375,0.323 10 false *1 3.01,0.542 3.271,0.927 0.26,0.385 10 false *2 0.188,1.198 0.646,1.635 0.458,0.438 10 false *3 1.083,0.042 1.469,0.292 0.385,0.25 10 false *4 0.156,1.865 0.49,2.344 0.333,0.479 10 false *a 0.646,0.844 1.042,1.094 0.396,0.25 10 false *5 0.375,2.427 0.833,2.865 0.458,0.438 10 false G7 1.938,3.083 2.594,3.333 0.656,0.25 10 false PAON 1.323,3.083 1.823,3.333 0.5,0.25 10 false P-AB 2.698,0.521 2.958,0.906 0.26,0.385 10 false A 2.323,0.521 2.583,0.906 0.26,0.385 10 false B 0.635,0.521 0.896,0.906 0.26,0.385 10 false C 0.448,0.521 0.708,0.906 0.26,0.385 10 false D 1.604,1.198 1.865,1.583 0.26,0.385 10 false E 1.229,1.208 1.49,1.594 0.26,0.385 10 false F 0.823,1.208 1.083,1.594 0.26,0.385 10 false G 0.438,1.208 0.698,1.594 0.26,0.385 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

14.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C295806C01
1.5,0.219 1.813,0.438 0.313,0.219 1.615,2.385 1.615,2.052 1.615,2.052 1.865,2.052 false 1.063,3.031 1.063,2.74 1.063,2.74 0.896,2.74 false 0.938,1.573 1.385,1.135 false 2.948,1.594 1.927,1.01 false 2.417,1.594 1.823,1.01 false 1.802,1.583 1.396,1.01 false 0.198,2.375 0.583,2.635 0.385,0.26 10 false *1 3.01,2.385 3.365,2.75 0.354,0.365 10 false *2 0.188,2.969 0.563,3.302 0.375,0.333 10 false *3 1.906,1.979 2.26,2.323 0.354,0.344 10 false *4 0.75,2.667 1.063,2.906 0.313,0.24 10 false *5 0.135,0.167 0.51,0.469 0.375,0.302 10 false *a 2.698,2.385 3.052,2.75 0.354,0.365 10 false A 2.323,2.385 2.677,2.75 0.354,0.365 10 false B 0.823,2.375 1.177,2.74 0.354,0.365 10 false C 0.448,2.375 0.802,2.74 0.354,0.365 10 false D 1.594,2.979 1.948,3.344 0.354,0.365 10 false E 1.229,2.979 1.583,3.344 0.354,0.365 10 false F 0.823,2.979 1.177,3.344 0.354,0.365 10 false G 0.448,2.979 0.802,3.344 0.354,0.365 10 false H 1.625,1.583 2.146,1.917 0.521,0.333 10 false PAON 2.24,1.583 2.76,1.917 0.521,0.333 10 false PAON 0.76,1.583 1.281,1.917 0.521,0.333 10 false P-AB 2.802,1.583 3.323,1.917 0.521,0.333 10 false P-AB 1.583,0.25 2.104,0.583 0.521,0.333 10 false 4A
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - 4A-26 (P-AB) Always 1 MΩ or higher
4A-23 (PAON) - 4A-44 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

15.CHECK NO. 4 INSTRUMENT PANEL WIRE (OPEN)
a.
C295805C01
0.219,0.615 0.552,0.833 0.333,0.219 0.875,3.698 1.208,3.917 0.333,0.219 2.073,2.208 2.24,2.208 2.24,2.208 2.24,2.625 false 0.917,2.854 1.083,2.854 1.083,2.854 1.083,2.521 false 1.333,1.167 1.552,0.823 false 1.854,1.156 1.656,0.823 false 1.156,4.323 1.563,3.76 false 2.115,4.333 1.729,3.76 false 1.635,4.448 1.635,4.24 false 1.167,1.823 1.531,2.104 0.365,0.281 10 false *1 2.99,1.823 3.313,2.292 0.323,0.469 10 false *2 0.208,2.417 0.604,2.792 0.396,0.375 10 false *3 2.177,2.646 2.479,2.917 0.302,0.271 10 false *4 0.76,2.781 1.146,3.177 0.385,0.396 10 false *5 0.177,0.115 0.51,0.406 0.333,0.292 10 false *a 0.719,3.125 1.052,3.417 0.333,0.292 10 false *b 2.688,1.823 3.01,2.292 0.323,0.469 10 false A 2.344,1.823 2.667,2.292 0.323,0.469 10 false B 1.615,1.823 1.938,2.292 0.323,0.469 10 false C 1.438,1.823 1.76,2.292 0.323,0.469 10 false D 1.635,2.427 1.958,2.896 0.323,0.469 10 false E 1.302,2.417 1.625,2.885 0.323,0.469 10 false F 0.802,2.427 1.125,2.896 0.323,0.469 10 false G 0.469,2.427 0.792,2.896 0.323,0.469 10 false H 1.646,1.167 2.146,1.5 0.5,0.333 10 false PAON 1.167,1.167 1.667,1.5 0.5,0.333 10 false P-AB 0.302,0.635 0.802,0.969 0.5,0.333 10 false G7 1.938,4.333 2.438,4.667 0.5,0.333 10 false PAON 0.979,4.333 1.479,4.667 0.5,0.333 10 false P-AB 1.563,4.458 1.823,4.667 0.26,0.208 10 false *6 0.917,3.719 1.417,4.052 0.5,0.333 10 false GF1
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*6 Service Wire
*a Front view of wire harness connector
(to Clock Assembly)
*b Front view of wire harness connector
(to Instrument Panel Wire)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Using a service wire, connect terminals 2 (PAON) and 1 (P-AB) of connector F.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always Below 1 Ω



d.

Disconnect the service wire from connector F.


Result:
Proceed to
OK
NG



OK

16.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

16.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C295803C01
1.594,0.146 1.906,0.365 0.313,0.219 1.135,3.458 1.458,3.677 0.323,0.219 2.333,4.396 2.333,4.208 false 1.625,2.219 1.625,1.885 1.625,1.885 1.875,1.885 false 1.094,2.854 1.094,2.531 1.094,2.531 1.26,2.531 false 1.479,1.417 1.823,0.917 false 2.281,1.427 1.927,0.917 false 1.75,4.323 2.052,3.885 false 2.927,4.333 2.521,3.646 false 0.177,2.188 0.5,2.51 0.323,0.323 10 false *1 3.01,2.208 3.427,2.615 0.417,0.406 10 false *2 0.177,2.802 0.656,3.292 0.479,0.49 10 false *3 1.906,1.802 2.26,2.063 0.354,0.26 10 false *4 1.292,2.458 1.719,2.771 0.427,0.313 10 false *5 0.125,0.115 0.542,0.458 0.417,0.344 10 false *a 0.938,3.167 1.375,3.719 0.438,0.552 10 false *b 2.26,4.406 2.469,4.594 0.208,0.188 10 false *6 2.698,2.198 3.115,2.604 0.417,0.406 10 false A 2.323,2.198 2.74,2.604 0.417,0.406 10 false B 0.823,2.198 1.24,2.604 0.417,0.406 10 false C 0.458,2.198 0.875,2.604 0.417,0.406 10 false D 1.646,2.792 2.063,3.198 0.417,0.406 10 false E 1.271,2.792 1.688,3.198 0.417,0.406 10 false F 0.813,2.802 1.229,3.208 0.417,0.406 10 false G 0.448,2.802 0.865,3.208 0.417,0.406 10 false H 1.667,0.167 2.146,0.656 0.479,0.49 10 false 4A 1.26,1.427 1.74,1.917 0.479,0.49 10 false PAON 2.125,1.427 2.604,1.917 0.479,0.49 10 false P-AB 2.771,4.344 3.271,4.583 0.5,0.24 10 false P-AB 1.5,4.344 1.979,4.583 0.479,0.24 10 false PAON 1.188,3.479 1.667,3.969 0.479,0.49 10 false F38
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*6 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - 4A-26 (P-AB) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


e.
C295804C01
1.542,0.146 1.833,0.344 0.292,0.198 0.344,3.552 0.688,3.771 0.344,0.219 1.542,2.104 1.542,1.729 1.542,1.729 1.792,1.729 false 1.083,2.74 1.083,2.417 1.083,2.417 1.25,2.417 false 2.25,4.448 2.25,4.302 false 0.969,1.385 1.385,0.875 false 1.677,1.365 1.385,1.01 false 1.698,4.302 2.167,3.646 false 2.781,4.313 2.323,3.646 false 0.167,2.083 0.552,2.365 0.385,0.281 10 false *1 3,2.083 3.313,2.479 0.313,0.396 10 false *2 0.177,2.688 0.438,3.063 0.26,0.375 10 false *3 1.823,1.656 2.125,1.917 0.302,0.26 10 false *4 1.281,2.333 1.563,2.625 0.281,0.292 10 false *5 2.177,4.469 2.427,4.656 0.25,0.188 10 false *6 0.135,0.115 0.469,0.406 0.333,0.292 10 false *a 0.26,3.146 0.635,3.583 0.375,0.438 10 false *b 2.698,2.083 3.01,2.479 0.313,0.396 10 false A 2.323,2.094 2.635,2.49 0.313,0.396 10 false B 0.823,2.083 1.135,2.479 0.313,0.396 10 false C 0.448,2.083 0.76,2.479 0.313,0.396 10 false D 1.646,2.688 1.958,3.083 0.313,0.396 10 false E 1.271,2.688 1.583,3.083 0.313,0.396 10 false F 0.813,2.688 1.125,3.083 0.313,0.396 10 false G 0.448,2.688 0.76,3.083 0.313,0.396 10 false H 2.656,4.313 3.073,4.583 0.417,0.271 10 false P-AB 1.5,4.313 1.917,4.583 0.417,0.271 10 false PAON 0.385,3.573 0.802,3.844 0.417,0.271 10 false GF1 1.604,0.167 2.021,0.438 0.417,0.271 10 false 4A 1.552,1.375 1.969,1.646 0.417,0.271 10 false P-AB 0.771,1.375 1.188,1.646 0.417,0.271 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*6 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to No. 4 Instrument Panel Wire)


Using a service wire, connect terminals 2 (PAON) and 1 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-23 (PAON) - 4A-44 (P-AB) Always Below 1 Ω



g.

Disconnect the service wire from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

17.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, clock assembly and instrument panel junction block assembly. Also check that the connectors that link the No. 4 instrument panel wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, clock assembly and instrument panel junction block assembly. Also disconnect the connectors that link the No. 4 instrument panel wire and instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

18.CHECK WIRE HARNESS (OPEN)

NG

REPLACE WIRE HARNESS

18.CHECK WIRE HARNESS (OPEN)
a.
C295808C01
0.333,0.427 0.667,0.656 0.333,0.229 0.302,3.708 0.635,3.938 0.333,0.229 1.531,1.427 1.531,1.177 false 0.865,1.24 1.271,0.833 false 2.167,1.25 1.719,0.604 false 1.323,4.344 1.708,3.979 false 2.198,4.344 1.823,3.979 false 0.188,2 0.563,2.271 0.375,0.271 10 false *1 3.01,2.01 3.323,2.344 0.313,0.333 10 false *2 0.208,2.677 0.646,3.073 0.438,0.396 10 false *3 1.458,1.448 1.896,1.792 0.438,0.344 10 false *4 0.156,0.125 0.594,0.583 0.438,0.458 10 false *a 0.135,3.271 0.552,3.635 0.417,0.365 10 false *b 0.385,0.458 0.76,0.729 0.375,0.271 10 false F38 0.667,1.25 1.25,1.5 0.583,0.25 10 false PAON 2.021,1.25 2.604,1.5 0.583,0.25 10 false P-AB 2.021,4.333 2.604,4.583 0.583,0.25 10 false PAON 1.177,4.333 1.76,4.583 0.583,0.25 10 false P-AB 0.385,3.74 0.76,4.01 0.375,0.271 10 false G7 2.698,2.01 3.01,2.344 0.313,0.333 10 false A 2.323,2.01 2.635,2.344 0.313,0.333 10 false B 0.625,2.01 0.938,2.344 0.313,0.333 10 false C 0.448,2.01 0.76,2.344 0.313,0.333 10 false D 1.563,2.677 1.875,3.01 0.313,0.333 10 false E 1.375,2.677 1.688,3.01 0.313,0.333 10 false F 0.813,2.677 1.125,3.01 0.313,0.333 10 false G 0.448,2.677 0.76,3.01 0.313,0.333 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Clock Assembly)


Connect the connector to the instrument panel junction block assembly.


b.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

19.CHECK WIRE HARNESS (SHORT)

NG

31.CHECK NO. 4 INSTRUMENT PANEL WIRE (OPEN)
19.CHECK WIRE HARNESS (SHORT)
a.
C295809C01
0.333,2.396 0.656,2.615 0.323,0.219 1.417,2.99 1.719,2.646 false 2.167,2.979 1.844,2.646 false 0.177,0.51 0.5,0.719 0.323,0.208 10 false *1 2.99,0.531 3.313,0.802 0.323,0.271 10 false *2 0.177,1.198 0.615,1.542 0.438,0.344 10 false *3 2.698,0.521 3,0.823 0.302,0.302 10 false A 0.177,1.854 0.573,2.177 0.396,0.323 10 false *a 2.323,0.521 2.635,0.823 0.313,0.302 10 false B 0.635,0.531 0.948,0.833 0.313,0.302 10 false C 0.448,0.531 0.76,0.833 0.313,0.302 10 false D 1.521,1.208 1.833,1.51 0.313,0.302 10 false E 1.333,1.208 1.646,1.51 0.313,0.302 10 false F 0.823,1.208 1.135,1.51 0.313,0.302 10 false G 0.448,1.208 0.76,1.51 0.313,0.302 10 false H 0.406,2.417 0.802,2.74 0.396,0.323 10 false G7 2,3 2.5,3.323 0.5,0.323 10 false PAON 1.25,3 1.792,3.333 0.542,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Clock Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK WIRE HARNESS (SHORT TO B+)

NG

29.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT)
20.CHECK WIRE HARNESS (SHORT TO B+)
a.
C295809C01
0.333,2.396 0.656,2.615 0.323,0.219 1.417,2.99 1.719,2.646 false 2.167,2.979 1.844,2.646 false 0.177,0.51 0.5,0.719 0.323,0.208 10 false *1 2.99,0.531 3.313,0.802 0.323,0.271 10 false *2 0.177,1.198 0.615,1.542 0.438,0.344 10 false *3 2.698,0.521 3,0.823 0.302,0.302 10 false A 0.177,1.854 0.573,2.177 0.396,0.323 10 false *a 2.323,0.521 2.635,0.823 0.313,0.302 10 false B 0.635,0.531 0.948,0.833 0.313,0.302 10 false C 0.448,0.531 0.76,0.833 0.313,0.302 10 false D 1.521,1.208 1.833,1.51 0.313,0.302 10 false E 1.333,1.208 1.646,1.51 0.313,0.302 10 false F 0.823,1.208 1.135,1.51 0.313,0.302 10 false G 0.448,1.208 0.76,1.51 0.313,0.302 10 false H 0.406,2.417 0.802,2.74 0.396,0.323 10 false G7 2,3 2.5,3.323 0.5,0.323 10 false PAON 1.25,3 1.792,3.333 0.542,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Clock Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Ignition switch ON Below 1 V
G7-15 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

21.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

27.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO B+)
21.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C295809C01
0.333,2.396 0.656,2.615 0.323,0.219 1.417,2.99 1.719,2.646 false 2.167,2.979 1.844,2.646 false 0.177,0.51 0.5,0.719 0.323,0.208 10 false *1 2.99,0.531 3.313,0.802 0.323,0.271 10 false *2 0.177,1.198 0.615,1.542 0.438,0.344 10 false *3 2.698,0.521 3,0.823 0.302,0.302 10 false A 0.177,1.854 0.573,2.177 0.396,0.323 10 false *a 2.323,0.521 2.635,0.823 0.313,0.302 10 false B 0.635,0.531 0.948,0.833 0.313,0.302 10 false C 0.448,0.531 0.76,0.833 0.313,0.302 10 false D 1.521,1.208 1.833,1.51 0.313,0.302 10 false E 1.333,1.208 1.646,1.51 0.313,0.302 10 false F 0.823,1.208 1.135,1.51 0.313,0.302 10 false G 0.448,1.208 0.76,1.51 0.313,0.302 10 false H 0.406,2.417 0.802,2.74 0.396,0.323 10 false G7 2,3 2.5,3.323 0.5,0.323 10 false PAON 1.25,3 1.792,3.333 0.542,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Clock Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Always 1 MΩ or higher
G7-15 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

25.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO GROUND)
22.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
C295809C02
0.333,2.396 0.656,2.615 0.323,0.219 0.74,2.979 1.052,2.479 false 0.177,0.51 0.5,0.719 0.323,0.208 10 false *1 2.99,0.531 3.313,0.802 0.323,0.271 10 false *2 0.177,1.198 0.615,1.542 0.438,0.344 10 false *3 2.698,0.521 3,0.823 0.302,0.302 10 false A 0.177,1.854 0.573,2.177 0.396,0.323 10 false *a 2.323,0.521 2.635,0.823 0.313,0.302 10 false B 0.635,0.531 0.948,0.833 0.313,0.302 10 false C 0.448,0.531 0.76,0.833 0.313,0.302 10 false D 1.521,1.208 1.833,1.51 0.313,0.302 10 false E 1.333,1.208 1.646,1.51 0.313,0.302 10 false F 0.823,1.208 1.135,1.51 0.313,0.302 10 false G 0.448,1.208 0.76,1.51 0.313,0.302 10 false H 0.406,2.417 0.802,2.74 0.396,0.323 10 false G7 0.615,3 1.156,3.333 0.542,0.333 10 false IG+
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Clock Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

23.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR BATTERY

23.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C295802C01
1.083,2.281 1.417,2.521 0.333,0.24 1.823,3.042 2.021,2.719 false 2.833,3.052 2.479,2.469 false 0.26,0.531 0.625,0.823 0.365,0.292 10 false *1 2.896,0.531 3.229,0.927 0.333,0.396 10 false *2 0.271,1.219 0.708,1.708 0.438,0.49 10 false *3 0.896,1.844 1.354,2.375 0.458,0.531 10 false *a 1.135,2.323 1.594,2.854 0.458,0.531 10 false F38 1.625,3.042 2.094,3.333 0.469,0.292 10 false PAON 2.688,3.042 3.156,3.333 0.469,0.292 10 false P-AB 2.594,0.531 2.927,0.927 0.333,0.396 10 false A 2.219,0.531 2.552,0.927 0.333,0.396 10 false B 0.719,0.542 1.052,0.938 0.333,0.396 10 false C 0.531,0.542 0.865,0.938 0.333,0.396 10 false D 1.427,1.219 1.76,1.615 0.333,0.396 10 false E 1.25,1.219 1.583,1.615 0.333,0.396 10 false F 0.719,1.219 1.052,1.615 0.333,0.396 10 false G 0.531,1.219 0.865,1.615 0.333,0.396 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the connector to the clock assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator according to the conditions in the table below.

OK:
Terminal Connection Condition Specified Condition
F38-23 (PAON) - Body ground Ignition switch ON "ON" comes on
F38-17 (P-AB) - Body ground Ignition switch ON "OFF" comes on



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

24.CHECK DTC

NG

24.CHECK DTC
a.
C295810C01
2.615,0.771 2.927,0.927 0.313,0.156 10 false A 1.323,1.49 1.635,1.646 0.313,0.156 10 false F 0.729,1.49 1.042,1.646 0.313,0.156 10 false G 0.281,0.802 0.604,1.031 0.323,0.229 10 false *1 2.917,0.771 3.292,1.083 0.375,0.313 10 false *2 0.302,1.49 0.729,1.813 0.427,0.323 10 false *3 2.427,0.771 2.74,0.927 0.313,0.156 10 false B 0.74,0.802 1.052,0.958 0.313,0.156 10 false C 0.552,0.802 0.865,0.958 0.313,0.156 10 false D 1.51,1.49 1.823,1.646 0.313,0.156 10 false E 0.552,1.49 0.865,1.646 0.313,0.156 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly


Connect the connector to the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

25.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C295807C01
0.292,2.396 0.635,2.615 0.344,0.219 1.479,0.542 1.479,0.125 1.479,0.125 1.229,0.125 false 1.063,1.26 1.063,0.927 1.063,0.927 0.813,0.927 false 1.5,3.063 1.719,2.635 false 2.104,3.052 1.823,2.635 false 0.177,0.51 0.552,0.833 0.375,0.323 10 false *1 3.01,0.542 3.271,0.927 0.26,0.385 10 false *2 0.188,1.198 0.646,1.635 0.458,0.438 10 false *3 1.083,0.042 1.469,0.292 0.385,0.25 10 false *4 0.156,1.865 0.49,2.344 0.333,0.479 10 false *a 0.646,0.844 1.042,1.094 0.396,0.25 10 false *5 0.375,2.427 0.833,2.865 0.458,0.438 10 false G7 1.938,3.083 2.594,3.333 0.656,0.25 10 false PAON 1.323,3.083 1.823,3.333 0.5,0.25 10 false P-AB 2.698,0.521 2.958,0.906 0.26,0.385 10 false A 2.323,0.521 2.583,0.906 0.26,0.385 10 false B 0.635,0.521 0.896,0.906 0.26,0.385 10 false C 0.448,0.521 0.708,0.906 0.26,0.385 10 false D 1.604,1.198 1.865,1.583 0.26,0.385 10 false E 1.229,1.208 1.49,1.594 0.26,0.385 10 false F 0.823,1.208 1.083,1.594 0.26,0.385 10 false G 0.438,1.208 0.698,1.594 0.26,0.385 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Always 1 MΩ or higher
G7-15 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

26.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C295806C01
1.5,0.219 1.813,0.438 0.313,0.219 1.615,2.385 1.615,2.052 1.615,2.052 1.865,2.052 false 1.063,3.031 1.063,2.74 1.063,2.74 0.896,2.74 false 0.938,1.573 1.385,1.135 false 2.948,1.594 1.927,1.01 false 2.417,1.594 1.823,1.01 false 1.802,1.583 1.396,1.01 false 0.198,2.375 0.583,2.635 0.385,0.26 10 false *1 3.01,2.385 3.365,2.75 0.354,0.365 10 false *2 0.188,2.969 0.563,3.302 0.375,0.333 10 false *3 1.906,1.979 2.26,2.323 0.354,0.344 10 false *4 0.75,2.667 1.063,2.906 0.313,0.24 10 false *5 0.135,0.167 0.51,0.469 0.375,0.302 10 false *a 2.698,2.385 3.052,2.75 0.354,0.365 10 false A 2.323,2.385 2.677,2.75 0.354,0.365 10 false B 0.823,2.375 1.177,2.74 0.354,0.365 10 false C 0.448,2.375 0.802,2.74 0.354,0.365 10 false D 1.594,2.979 1.948,3.344 0.354,0.365 10 false E 1.229,2.979 1.583,3.344 0.354,0.365 10 false F 0.823,2.979 1.177,3.344 0.354,0.365 10 false G 0.448,2.979 0.802,3.344 0.354,0.365 10 false H 1.625,1.583 2.146,1.917 0.521,0.333 10 false PAON 2.24,1.583 2.76,1.917 0.521,0.333 10 false PAON 0.76,1.583 1.281,1.917 0.521,0.333 10 false P-AB 2.802,1.583 3.323,1.917 0.521,0.333 10 false P-AB 1.583,0.25 2.104,0.583 0.521,0.333 10 false 4A
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - Body ground Always 1 MΩ or higher
4A-23 (PAON) - Body ground Always 1 MΩ or higher
4A-26 (P-AB) - Body ground Always 1 MΩ or higher
4A-44 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

27.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C295807C01
0.292,2.396 0.635,2.615 0.344,0.219 1.479,0.542 1.479,0.125 1.479,0.125 1.229,0.125 false 1.063,1.26 1.063,0.927 1.063,0.927 0.813,0.927 false 1.5,3.063 1.719,2.635 false 2.104,3.052 1.823,2.635 false 0.177,0.51 0.552,0.833 0.375,0.323 10 false *1 3.01,0.542 3.271,0.927 0.26,0.385 10 false *2 0.188,1.198 0.646,1.635 0.458,0.438 10 false *3 1.083,0.042 1.469,0.292 0.385,0.25 10 false *4 0.156,1.865 0.49,2.344 0.333,0.479 10 false *a 0.646,0.844 1.042,1.094 0.396,0.25 10 false *5 0.375,2.427 0.833,2.865 0.458,0.438 10 false G7 1.938,3.083 2.594,3.333 0.656,0.25 10 false PAON 1.323,3.083 1.823,3.333 0.5,0.25 10 false P-AB 2.698,0.521 2.958,0.906 0.26,0.385 10 false A 2.323,0.521 2.583,0.906 0.26,0.385 10 false B 0.635,0.521 0.896,0.906 0.26,0.385 10 false C 0.448,0.521 0.708,0.906 0.26,0.385 10 false D 1.604,1.198 1.865,1.583 0.26,0.385 10 false E 1.229,1.208 1.49,1.594 0.26,0.385 10 false F 0.823,1.208 1.083,1.594 0.26,0.385 10 false G 0.438,1.208 0.698,1.594 0.26,0.385 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-16 (PAON) - Body ground Ignition switch ON Below 1 V
G7-15 (P-AB) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

28.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

28.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C295806C01
1.5,0.219 1.813,0.438 0.313,0.219 1.615,2.385 1.615,2.052 1.615,2.052 1.865,2.052 false 1.063,3.031 1.063,2.74 1.063,2.74 0.896,2.74 false 0.938,1.573 1.385,1.135 false 2.948,1.594 1.927,1.01 false 2.417,1.594 1.823,1.01 false 1.802,1.583 1.396,1.01 false 0.198,2.375 0.583,2.635 0.385,0.26 10 false *1 3.01,2.385 3.365,2.75 0.354,0.365 10 false *2 0.188,2.969 0.563,3.302 0.375,0.333 10 false *3 1.906,1.979 2.26,2.323 0.354,0.344 10 false *4 0.75,2.667 1.063,2.906 0.313,0.24 10 false *5 0.135,0.167 0.51,0.469 0.375,0.302 10 false *a 2.698,2.385 3.052,2.75 0.354,0.365 10 false A 2.323,2.385 2.677,2.75 0.354,0.365 10 false B 0.823,2.375 1.177,2.74 0.354,0.365 10 false C 0.448,2.375 0.802,2.74 0.354,0.365 10 false D 1.594,2.979 1.948,3.344 0.354,0.365 10 false E 1.229,2.979 1.583,3.344 0.354,0.365 10 false F 0.823,2.979 1.177,3.344 0.354,0.365 10 false G 0.448,2.979 0.802,3.344 0.354,0.365 10 false H 1.625,1.583 2.146,1.917 0.521,0.333 10 false PAON 2.24,1.583 2.76,1.917 0.521,0.333 10 false PAON 0.76,1.583 1.281,1.917 0.521,0.333 10 false P-AB 2.802,1.583 3.323,1.917 0.521,0.333 10 false P-AB 1.583,0.25 2.104,0.583 0.521,0.333 10 false 4A
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - Other terminals Always 1 MΩ or higher
4A-23 (PAON) - Other terminals Always 1 MΩ or higher
4A-26 (P-AB) - Other terminals Always 1 MΩ or higher
4A-44 (P-AB) - Other terminals Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

29.CHECK NO. 4 INSTRUMENT PANEL WIRE (SHORT)
a.
C295807C01
0.292,2.396 0.635,2.615 0.344,0.219 1.479,0.542 1.479,0.125 1.479,0.125 1.229,0.125 false 1.063,1.26 1.063,0.927 1.063,0.927 0.813,0.927 false 1.5,3.063 1.719,2.635 false 2.104,3.052 1.823,2.635 false 0.177,0.51 0.552,0.833 0.375,0.323 10 false *1 3.01,0.542 3.271,0.927 0.26,0.385 10 false *2 0.188,1.198 0.646,1.635 0.458,0.438 10 false *3 1.083,0.042 1.469,0.292 0.385,0.25 10 false *4 0.156,1.865 0.49,2.344 0.333,0.479 10 false *a 0.646,0.844 1.042,1.094 0.396,0.25 10 false *5 0.375,2.427 0.833,2.865 0.458,0.438 10 false G7 1.938,3.083 2.594,3.333 0.656,0.25 10 false PAON 1.323,3.083 1.823,3.333 0.5,0.25 10 false P-AB 2.698,0.521 2.958,0.906 0.26,0.385 10 false A 2.323,0.521 2.583,0.906 0.26,0.385 10 false B 0.635,0.521 0.896,0.906 0.26,0.385 10 false C 0.448,0.521 0.708,0.906 0.26,0.385 10 false D 1.604,1.198 1.865,1.583 0.26,0.385 10 false E 1.229,1.208 1.49,1.594 0.26,0.385 10 false F 0.823,1.208 1.083,1.594 0.26,0.385 10 false G 0.438,1.208 0.698,1.594 0.26,0.385 10 false H
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

30.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C295806C01
1.5,0.219 1.813,0.438 0.313,0.219 1.615,2.385 1.615,2.052 1.615,2.052 1.865,2.052 false 1.063,3.031 1.063,2.74 1.063,2.74 0.896,2.74 false 0.938,1.573 1.385,1.135 false 2.948,1.594 1.927,1.01 false 2.417,1.594 1.823,1.01 false 1.802,1.583 1.396,1.01 false 0.198,2.375 0.583,2.635 0.385,0.26 10 false *1 3.01,2.385 3.365,2.75 0.354,0.365 10 false *2 0.188,2.969 0.563,3.302 0.375,0.333 10 false *3 1.906,1.979 2.26,2.323 0.354,0.344 10 false *4 0.75,2.667 1.063,2.906 0.313,0.24 10 false *5 0.135,0.167 0.51,0.469 0.375,0.302 10 false *a 2.698,2.385 3.052,2.75 0.354,0.365 10 false A 2.323,2.385 2.677,2.75 0.354,0.365 10 false B 0.823,2.375 1.177,2.74 0.354,0.365 10 false C 0.448,2.375 0.802,2.74 0.354,0.365 10 false D 1.594,2.979 1.948,3.344 0.354,0.365 10 false E 1.229,2.979 1.583,3.344 0.354,0.365 10 false F 0.823,2.979 1.177,3.344 0.354,0.365 10 false G 0.448,2.979 0.802,3.344 0.354,0.365 10 false H 1.625,1.583 2.146,1.917 0.521,0.333 10 false PAON 2.24,1.583 2.76,1.917 0.521,0.333 10 false PAON 0.76,1.583 1.281,1.917 0.521,0.333 10 false P-AB 2.802,1.583 3.323,1.917 0.521,0.333 10 false P-AB 1.583,0.25 2.104,0.583 0.521,0.333 10 false 4A
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - 4A-26 (P-AB) Always 1 MΩ or higher
4A-23 (PAON) - 4A-44 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

31.CHECK NO. 4 INSTRUMENT PANEL WIRE (OPEN)
a.
C295805C01
0.219,0.615 0.552,0.833 0.333,0.219 0.875,3.698 1.208,3.917 0.333,0.219 2.073,2.208 2.24,2.208 2.24,2.208 2.24,2.625 false 0.917,2.854 1.083,2.854 1.083,2.854 1.083,2.521 false 1.333,1.167 1.552,0.823 false 1.854,1.156 1.656,0.823 false 1.156,4.323 1.563,3.76 false 2.115,4.333 1.729,3.76 false 1.635,4.448 1.635,4.24 false 1.167,1.823 1.531,2.104 0.365,0.281 10 false *1 2.99,1.823 3.313,2.292 0.323,0.469 10 false *2 0.208,2.417 0.604,2.792 0.396,0.375 10 false *3 2.177,2.646 2.479,2.917 0.302,0.271 10 false *4 0.76,2.781 1.146,3.177 0.385,0.396 10 false *5 0.177,0.115 0.51,0.406 0.333,0.292 10 false *a 0.719,3.125 1.052,3.417 0.333,0.292 10 false *b 2.688,1.823 3.01,2.292 0.323,0.469 10 false A 2.344,1.823 2.667,2.292 0.323,0.469 10 false B 1.615,1.823 1.938,2.292 0.323,0.469 10 false C 1.438,1.823 1.76,2.292 0.323,0.469 10 false D 1.635,2.427 1.958,2.896 0.323,0.469 10 false E 1.302,2.417 1.625,2.885 0.323,0.469 10 false F 0.802,2.427 1.125,2.896 0.323,0.469 10 false G 0.469,2.427 0.792,2.896 0.323,0.469 10 false H 1.646,1.167 2.146,1.5 0.5,0.333 10 false PAON 1.167,1.167 1.667,1.5 0.5,0.333 10 false P-AB 0.302,0.635 0.802,0.969 0.5,0.333 10 false G7 1.938,4.333 2.438,4.667 0.5,0.333 10 false PAON 0.979,4.333 1.479,4.667 0.5,0.333 10 false P-AB 1.563,4.458 1.823,4.667 0.26,0.208 10 false *6 0.917,3.719 1.417,4.052 0.5,0.333 10 false GF1
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*6 Service Wire
*a Front view of wire harness connector
(to Clock Assembly)
*b Front view of wire harness connector
(to Instrument Panel Wire)


Disconnect the No. 4 instrument panel wire connector from the instrument panel wire.


b.

Using a service wire, connect terminals 2 (PAON) and 1 (P-AB) of connector F.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (PAON) - G7-15 (P-AB) Always Below 1 Ω



d.

Disconnect the service wire from connector F.


Result:
Proceed to
OK
NG



OK

32.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE NO. 4 INSTRUMENT PANEL WIRE

32.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C295803C01
1.594,0.146 1.906,0.365 0.313,0.219 1.135,3.458 1.458,3.677 0.323,0.219 2.333,4.396 2.333,4.208 false 1.625,2.219 1.625,1.885 1.625,1.885 1.875,1.885 false 1.094,2.854 1.094,2.531 1.094,2.531 1.26,2.531 false 1.479,1.417 1.823,0.917 false 2.281,1.427 1.927,0.917 false 1.75,4.323 2.052,3.885 false 2.927,4.333 2.521,3.646 false 0.177,2.188 0.5,2.51 0.323,0.323 10 false *1 3.01,2.208 3.427,2.615 0.417,0.406 10 false *2 0.177,2.802 0.656,3.292 0.479,0.49 10 false *3 1.906,1.802 2.26,2.063 0.354,0.26 10 false *4 1.292,2.458 1.719,2.771 0.427,0.313 10 false *5 0.125,0.115 0.542,0.458 0.417,0.344 10 false *a 0.938,3.167 1.375,3.719 0.438,0.552 10 false *b 2.26,4.406 2.469,4.594 0.208,0.188 10 false *6 2.698,2.198 3.115,2.604 0.417,0.406 10 false A 2.323,2.198 2.74,2.604 0.417,0.406 10 false B 0.823,2.198 1.24,2.604 0.417,0.406 10 false C 0.458,2.198 0.875,2.604 0.417,0.406 10 false D 1.646,2.792 2.063,3.198 0.417,0.406 10 false E 1.271,2.792 1.688,3.198 0.417,0.406 10 false F 0.813,2.802 1.229,3.208 0.417,0.406 10 false G 0.448,2.802 0.865,3.208 0.417,0.406 10 false H 1.667,0.167 2.146,0.656 0.479,0.49 10 false 4A 1.26,1.427 1.74,1.917 0.479,0.49 10 false PAON 2.125,1.427 2.604,1.917 0.479,0.49 10 false P-AB 2.771,4.344 3.271,4.583 0.5,0.24 10 false P-AB 1.5,4.344 1.979,4.583 0.479,0.24 10 false PAON 1.188,3.479 1.667,3.969 0.479,0.49 10 false F38
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*6 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-25 (PAON) - 4A-26 (P-AB) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


e.
C295804C01
1.542,0.146 1.833,0.344 0.292,0.198 0.344,3.552 0.688,3.771 0.344,0.219 1.542,2.104 1.542,1.729 1.542,1.729 1.792,1.729 false 1.083,2.74 1.083,2.417 1.083,2.417 1.25,2.417 false 2.25,4.448 2.25,4.302 false 0.969,1.385 1.385,0.875 false 1.677,1.365 1.385,1.01 false 1.698,4.302 2.167,3.646 false 2.781,4.313 2.323,3.646 false 0.167,2.083 0.552,2.365 0.385,0.281 10 false *1 3,2.083 3.313,2.479 0.313,0.396 10 false *2 0.177,2.688 0.438,3.063 0.26,0.375 10 false *3 1.823,1.656 2.125,1.917 0.302,0.26 10 false *4 1.281,2.333 1.563,2.625 0.281,0.292 10 false *5 2.177,4.469 2.427,4.656 0.25,0.188 10 false *6 0.135,0.115 0.469,0.406 0.333,0.292 10 false *a 0.26,3.146 0.635,3.583 0.375,0.438 10 false *b 2.698,2.083 3.01,2.479 0.313,0.396 10 false A 2.323,2.094 2.635,2.49 0.313,0.396 10 false B 0.823,2.083 1.135,2.479 0.313,0.396 10 false C 0.448,2.083 0.76,2.479 0.313,0.396 10 false D 1.646,2.688 1.958,3.083 0.313,0.396 10 false E 1.271,2.688 1.583,3.083 0.313,0.396 10 false F 0.813,2.688 1.125,3.083 0.313,0.396 10 false G 0.448,2.688 0.76,3.083 0.313,0.396 10 false H 2.656,4.313 3.073,4.583 0.417,0.271 10 false P-AB 1.5,4.313 1.917,4.583 0.417,0.271 10 false PAON 0.385,3.573 0.802,3.844 0.417,0.271 10 false GF1 1.604,0.167 2.021,0.438 0.417,0.271 10 false 4A 1.552,1.375 1.969,1.646 0.417,0.271 10 false P-AB 0.771,1.375 1.188,1.646 0.417,0.271 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Clock Assembly
*4 Instrument Panel Wire
*5 No. 4 Instrument Panel Wire
*6 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to No. 4 Instrument Panel Wire)


Using a service wire, connect terminals 2 (PAON) and 1 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-23 (PAON) - 4A-44 (P-AB) Always Below 1 Ω



g.

Disconnect the service wire from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE