Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE › 2013.12–2016.11
RM3160E _52 Drivetrain _019725 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0107326 TRANSMISSION CONTROL CABLE A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.


a.

Pass the transmission control cable assembly from the cabin to the engine compartment.


b.

Install the transmission control cable assembly with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Install the dash panel insulator to the original position.


d.

Connect the transmission control cable assembly to the No. 3 transmission control cable bracket.


e.

Install a new clip to the No. 1 transmission control cable bracket.


f.
C102659C02
2.229,1.135 2.76,1.135 true 2.198,0.938 0.438,1.635 0.438,1.635 1.063,0.99 true 2.125,0.625 0.75,0.177 0.75,0.177 1.198,0.635 true 0.563,0.063 0.844,0.313 0.281,0.25 10 false *a 0.271,1.625 0.583,1.885 0.313,0.26 10 false *b 2.771,1.052 3.031,1.313 0.26,0.26 10 false *c
*a Claw A
*b Claw B
*c Transmission Control Cable Assembly


Connect the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:
·

Make sure that the claws A on the clip are securely fit into the No. 1 transmission control cable bracket holes.

·

Make sure that the transmission control cable assembly is securely installed inside of the claws B of the clip.




g.

Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.



h.

Engage the wire harness clamp.


i.
C194520C31
2.271,2.573 2.615,2.573 false 1.948,1.75 2.083,1.531 2.083,1.531 2.188,1.531 false 1.594,0.958 1.781,1.135 0.188,0.177 10 false *c 1.792,1.344 1.979,1.521 0.188,0.177 10 false *c 2.438,0.781 2.625,0.958 0.188,0.177 10 false *d 2.25,1.458 2.51,1.656 0.26,0.198 10 false *a 2.229,2.313 2.417,2.49 0.188,0.177 10 false *d 2.656,2.49 2.958,2.729 0.302,0.24 10 false *b
*a Slider
*b Lock Piece
*c Slide
*d Pull


Slide the slider of the transmission control cable assembly in the direction indicated by the arrow in the illustration and pull the lock piece outward.


j.
C163770C01
2.323,1 2.885,2.26 2.885,2.26 2.313,3.25 false 1.74,1.042 0.802,0.635 0.802,0.635 0.625,0.635 false 1.75,3.271 0.802,2.865 0.802,2.865 0.625,2.865 false 0.448,0.542 0.604,0.729 0.156,0.188 10 false *a 2.344,0.417 2.563,0.583 0.219,0.167 10 false *b 0.458,2.781 0.615,2.969 0.156,0.188 10 false *a 2.927,2.177 3.146,2.344 0.219,0.167 10 false *c
*a Lock Nut
*b Push in
*c Stopper


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


k.
C299011C01
1.729,0.552 1.865,0.208 1.865,0.208 2.01,0.208 false 2.083,0.125 2.49,0.406 0.406,0.281 10 false *a 0.948,0.646 1.354,0.927 0.406,0.281 10 false A 2.396,0.646 2.802,0.927 0.406,0.281 10 false A
*a Stopper


Install the outer part of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:

After installation, check that the outer part of the cable lock is protruding beyond portion A-A as shown in the illustration.



l.
C299019C01
1.344,2.531 1.469,2.531 1.469,2.531 1.625,2.771 false 2.521,2.479 2.385,2.479 2.385,2.479 2.281,2.677 false 2.583,2.406 2.833,2.615 0.25,0.208 10 false *a 1.146,2.458 1.385,2.708 0.24,0.25 10 false *b
*a Lock Piece
*b Adjuster Case


Install the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Check that the lock piece is pulled out.

·

Install the cable end all the way to the base of the transmission floor shift assembly pin.




m.
C296262

Push the lock piece into the adjuster case.

NOTICE:
·

Check that the park/neutral position switch assembly and shift lever are in neutral.

·

Securely push in the lock piece until the slider lock is engaged.




Hide 46410 2.CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.

Connect the No. 1 parking brake cable assembly with the 3 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.
C296269

Install the floor carpet to the original position.


Hide 17701 4.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 5.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 6.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17750A 7.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 8.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53298E 9.INSTALL RADIATOR SIDE SEAL RH

Hide 53299D 10.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH