Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109955 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.

Engage the 2 claws.


b.

Temporarily install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it. Failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Engage the 3 guides to temporarily install the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.

E285689


b.

Install the 6 bolts as shown in the illustration.

E285687C01
1.24,1.135 1.51,1.021 false 1.875,0.896 2.156,0.667 false 1.927,1.24 2.135,1.115 false 1.063,1.042 1.375,1.24 0.313,0.198 10 false *a 2.177,0.531 2.49,0.729 0.313,0.198 10 false *b 2.156,0.979 2.469,1.177 0.313,0.198 10 false *1 0.25,0.167 0.563,0.365 0.313,0.198 10 false *c 1.333,0.167 1.646,0.365 0.313,0.198 10 false *d 2.333,0.167 2.646,0.365 0.313,0.198 10 false *e 3.417,0.167 3.729,0.365 0.313,0.198 10 false *f
*1 Instrument Panel Reinforcement Assembly - -
*a Movable Collar *b Vehicle Body
*c Step 1 *d Step 2
*e Step 3 *f Step 4
V100135

Bolt
V100136

Nut


Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Temporarily install the nut.


d.

Connect the drain cooler hose.


e.

Install the 2 hole plugs.


f.

Engage the claw to connect the drain cooler hose to the piping clamp.


g.

Install the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


h.

Install the 2 hole plugs.


i.

Engage each clamp.


j.

Connect each connector.


k.

for LHD:

i.

Connect the 4 earth wires with the 4 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



l.

for RHD:

i.

Connect the 3 earth wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



Hide 55458A 3.INSTALL INSTRUMENT PANEL SAFETY PAD CAP

a.
E285680C01
0.083,0.094 0.458,0.333 0.375,0.24 12 true *A 0.083,2.583 0.458,2.823 0.375,0.24 12 true *B
*A for LH Side
*B for RH Side


Install 4 new instrument panel safety pad caps.


Hide 55307C 4.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 2 instrument panel brace sub-assembly with the bolt, screw and 2 nuts.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)

HINT:

Do not fully tighten the screw.



b.

Engage each clamp.


Hide 55306A 5.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the 2 bolts, screw and 2 nuts.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)

HINT:

Do not fully tighten the screw.



b.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Engage each clamp.


Hide 6.FULLY TIGHTEN AIR CONDITIONING UNIT ASSEMBLY

a.

for LHD:

i.

Tighten the 3 bolts, 2 screws and nut.

E285693C01
2.771,1.031 2.927,1.229 0.156,0.198 10 true 1 4.25,1.031 4.406,1.229 0.156,0.198 10 true 3 5.708,1.01 5.865,1.208 0.156,0.198 10 true 2 6.042,4.604 6.198,4.802 0.156,0.198 10 true 6 4.594,5.354 4.75,5.552 0.156,0.198 10 true 5 2.167,5.406 2.323,5.604 0.156,0.198 10 true 4
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration to install the air conditioning unit assembly.




b.

for RHD:

i.

Tighten the 3 bolts, 2 screws and nut.

E285694C01
1.229,0.906 1.385,1.104 0.156,0.198 10 true 2 3.219,0.938 3.375,1.135 0.156,0.198 10 true 1 5.135,0.927 5.292,1.125 0.156,0.198 10 true 3 2.292,5.417 2.448,5.615 0.156,0.198 10 true 6 3.563,5.438 3.719,5.635 0.156,0.198 10 true 4 6.083,5.406 6.24,5.604 0.156,0.198 10 true 5
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration to install the air conditioning unit assembly.




Hide 85940 7.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 33525 8.INSTALL SHIFT LEVER SUPPORT

a.
E285674C02
0.292,0.615 0.448,0.813 0.156,0.198 10 true 1 1.927,0.219 2.083,0.417 0.156,0.198 10 true 2
V100135

Nut
V100136

Bolt


Install the 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the nuts in the order shown in the illustration.



b.

Install the shift lever support with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Engage each clamp.


d.

Connect each connector.


Hide 33550 9.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

for U660E Automatic Transmission / Transaxle:

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT LEVER>INSTALLATION

for U660F Automatic Transmission / Transaxle:

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT LEVER>INSTALLATION

for U760E Automatic Transmission / Transaxle:

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT LEVER>INSTALLATION

Hide 87214D 10.INSTALL REAR NO. 3 AIR DUCT

a.

Engage the 2 claws to install the rear No. 3 air duct.


Hide 87215D 11.INSTALL REAR NO. 4 AIR DUCT

a.

Install the rear No. 4 air duct with the clip.


b.
E285671C01
1.76,0.844 1.781,0.75 false
V100155

Fastener


Install the front floor carpet assembly to the original position as shown in the illustration.


c.

Engage the fastener and 4 guides.


Hide 87212 12.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 2 claws to install the rear No. 1 air duct.


b.

Engage the clamp to connect the wire harness.


Hide 87213 13.INSTALL REAR NO. 2 AIR DUCT

a.

Install the rear No. 2 air duct with the clip.


b.
E285667C01
1.698,1.104 1.656,1.031 false
V100155

Fastener


Install the front floor carpet assembly to the original position as shown in the illustration.


c.

Engage the 2 fasteners and 4 guides.


Hide 88625Q 14.INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR (for Automatic Air Conditioning System)

a.

Connect the aspirator and connector to install the cooler (room temp. sensor) thermistor.


Hide 15.INSTALL WIRE HARNESS CLAMP BRACKET (for LHD)

a.

Install the wire harness clamp bracket with the nut.


b.

Engage the 3 clamps.


Hide 16.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 88650N 17.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 82877 18.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 82878 19.INSTALL ECU INTEGRATION BOX LH (for RHD)

Hide 20.INSTALL STEERING POST ASSEMBLY

Hide 21.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 22.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 23.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 24.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

HINT:

Use the same procedure as for the LH side.


Hide 25.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:

Use the same procedure as for the LH side.


Hide 87245 26.CONNECT INLET HEATER WATER HOSE

a.
E285662C01
0.75,3.135 1.083,3.344 false 2.24,1.25 2.396,1.448 0.156,0.198 10 true A 0.531,2.344 0.844,2.542 0.313,0.198 10 false *a 0.76,4.031 1.073,4.229 0.313,0.198 10 false *c 0.573,3.01 0.885,3.208 0.313,0.198 10 false *b
*a View A
*b for 2GR-FE:
Marking (Blue)
for 1AR-FE:
Marking (Orange)
*c Clip Installation Angle (60 to 120°)


Connect the inlet heater water hose with the marking facing left and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.



Hide 87246 27.CONNECT OUTLET HEATER WATER HOSE

a.
E285663C01
1.115,3.896 1.417,3.604 false 2.313,1.021 2.469,1.219 0.156,0.198 10 true A 0.354,2.302 0.667,2.5 0.313,0.198 10 false *a 0.625,2.854 0.938,3.052 0.313,0.198 10 false *c 0.938,3.844 1.25,4.042 0.313,0.198 10 false *b
*a View A
*b for 2GR-FE:
Marking (Blue)
for 1AR-FE:
Marking (Orange)
*c Clip Installation Angle (15 to 75°)


Connect the outlet heater water hose with the marking facing left and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the outlet heater water hose.



Hide 28.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.


d.

Connect the air conditioner tube and accessory assembly.


Hide 88704 29.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.


d.

Connect the suction hose sub-assembly.


e.
E285664

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55701J 30.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for 2GR-FE)

Hide 31.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for 2GR-FE)

Hide 55781E 32.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53867H 33.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 34.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 35.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 36.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 85292B 37.INSTALL FRONT WIPER ARM HEAD CAP

Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 39.ADD ENGINE COOLANT (for 1AR-FE)

Hide 40.ADD ENGINE COOLANT (for 2GR-FE)

Hide 41.INSPECT FOR COOLANT LEAK (for 1AR-FE)

Hide 42.INSPECT FOR COOLANT LEAK (for 2GR-FE)

Hide 43.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT