Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › 2013.12–2015.11
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0107526 TRANSFER ASSEMBLY A

MF1A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Before installation of each part, thoroughly clean and dry it. Then apply grease or oil as necessary. Do not use alkaline chemicals to clean aluminum parts, rubber parts or precoated bolts. Also, do not use non-residue solvent or other cleaning oils to clean O-rings, oil seals or rubber parts.


PROCEDURE

Hide 36100A 1.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.
C197691

Remove the 4 transfer and transaxle setting stud bolts from the transfer case.


Hide 36114H 2.REMOVE NO. 2 TRANSFER CASE PLUG

a.
C141912

Remove the No. 2 transfer case plug from the transfer case.


b.

Remove the gasket from the No. 2 transfer case plug.


Hide 36114B 3.REMOVE NO. 1 TRANSFER CASE PLUG

a.
C141905

Remove the No. 1 transfer case plug from the transfer case.


b.

Remove the gasket from the No. 1 transfer case plug.


Hide 36114F 4.REMOVE TRANSFER DRAIN PLUG

a.
C141914

Remove the transfer drain plug from the transfer case.


b.

Remove the gasket from the transfer drain plug.


Hide 36111H 5.REMOVE TRANSFER CASE BREATHER PLUG

a.
C094714

Using a screwdriver, remove the transfer case breather plug from the transfer case cover sub-assembly.


Hide 36102 6.REMOVE TRANSFER CASE COVER SUB-ASSEMBLY

a.
C295121

Remove the 8 bolts from the transfer case cover sub-assembly.


b.
C155222

Using a brass bar and a hammer, remove the transfer case cover sub-assembly from the transfer case.

NOTICE:

Place the brass bar on the rib protruding from the transfer case cover sub-assembly.



Hide 36128B 7.REMOVE BREATHER OIL DEFLECTOR

a.
C066129

Remove the bolt and breather oil deflector from the transfer case cover sub-assembly.


Hide 36111G 8.REMOVE TRANSFER CASE STRAIGHT PIN

a.

Remove the 4 transfer case straight pins from the transfer case.

C295122


Hide 36100 9.SECURE TRANSFER ASSEMBLY

a.

Attach the transfer assembly to the overhaul attachment.


Hide 33146A 10.REMOVE TRANSFER EXTENSION HOUSING DUST DEFLECTOR

a.
C055351

Using a plastic hammer, remove the transfer extension housing dust deflector from the transfer extension housing sub-assembly.


Hide 36115C 11.REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL

a.
C155231N05
1.031,2.406 1.031,2.729 false 0.865,2.781 1.208,2.979 0.344,0.198 10 false SST

Using SST, remove the transfer extension housing type T oil seal from the transfer extension housing sub-assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the transfer extension housing type T oil seal contact surface or the inside surface of the transfer extension housing type T oil seal.



Hide 36109 12.REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

a.
C176636

Remove the 4 bolts from the transfer case.


b.
C176637

Using a plastic hammer, remove the transfer extension housing sub-assembly from the transfer case.


Hide 15.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

Hide 36111B 16.REMOVE TRANSFER CASE OIL SEAL

a.
C176639N03
2.573,2.448 2.573,2.708 false 2.427,2.781 2.76,2.979 0.333,0.198 10 false SST

Using SST, remove the transfer case oil seal from the transfer case.

SST
09308-00010  

NOTICE:
·

Do not damage the transfer case oil seal contact surface to the transfer case.

·

Wear or damage to the front drive shaft oil seal RH (for Inside) on the transmission side will cause transfer oil leakage.

If it is worn or damaged, replace the front drive shaft oil seal RH (for Inside).

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>DIFFERENTIAL OIL SEAL(for RH Side)>REPLACEMENT




Hide 36113A 17.REMOVE TRANSFER CASE OIL SEAL RH

a.
C155216N04
1.12,2.331 1.447,2.503 0.326,0.172 10 SST 1.273,2.008 1.273,2.306 false

Using SST, remove the transfer case oil seal RH from the transfer case.

SST
09308-00010  

NOTICE:

Do not damage the transfer case oil seal RH contact surface to the transfer case.



Hide 18.REMOVE BEARING CAP

a.
C052638

Remove the 2 bolts and bearing cap from the transfer case.


Hide 36255 19.REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER

a.
C186405C03
1.333,2.292 0.781,2.292 false 1.094,0.771 1.771,1.167 1.771,1.167 2.052,1.167 false 1.156,0.594 1.792,0.771 1.792,0.771 2.063,0.771 false 0.885,0.573 1.677,0.281 1.677,0.281 2.042,0.281 true 0.5,0.76 0.5,0.969 false 0.385,1 0.719,1.188 0.333,0.188 10 false SST 2.115,0.688 2.302,0.875 0.188,0.188 10 false *b 2.104,0.198 2.292,0.385 0.188,0.188 10 false *a 2.135,1.083 2.323,1.271 0.188,0.188 10 false *1 0.469,2.208 0.802,2.396 0.333,0.188 10 false SST
*1 No. 1 Transfer Output Shaft Spacer
*a Screwdriver
*b Piece of Cloth


Using SST, a screwdriver and a hammer, remove the No. 1 transfer output shaft spacer from the transfer case.

SST
09504-22012  

NOTICE:

Do not damage the transfer case.



Hide 41301X 20.REMOVE NO. 2 TRANSFER RING GEAR MOUNTING CASE WASHER

a.

Remove No. 2 transfer ring gear mounting case washer from the transfer case.


Hide 41319 21.REMOVE TRANSFER RING GEAR MOUNTING CASE

a.
C050974

Remove the transfer ring gear mounting case from the transfer case.


Hide 22.REMOVE DRIVEN PINION

a.
C094025N02
1.854,0.167 1.604,0.167 false 1.969,0.5 1.844,0.167 1.844,0.167 1.531,0.167 false 1.208,0.104 1.573,0.344 0.365,0.24 10 false SST

Using SST and a hammer, unstake the gear nut.

SST
09930-00010  

HINT:
·

Use SST with the flat side facing outward.

·

Do not machine the tip of SST with a grinder, etc.




b.
C300076C02
1.469,1.25 0.823,0.542 0.823,0.542 1.583,0.427 false 0.156,1.26 0.469,1.417 0.313,0.156 10 false *a 2.906,0.333 3.219,0.49 0.313,0.156 10 false *b 0.51,0.469 1.073,0.844 0.563,0.375 10 false SST
*a Turn
*b Hold


Using SST, remove the gear nut.

SST
09326-20011  09556-16030  


c.
C052642C01
0.698,0.448 1.031,0.448 false 0.719,0.75 1.052,0.75 false 0.656,1.344 1.042,1.344 false 1.125,0.385 1.438,0.542 0.313,0.156 10 false *1 1.135,0.698 1.448,0.854 0.313,0.156 10 false *2 1.125,1.271 1.438,1.427 0.313,0.156 10 false *3
*1 Rear Transfer Driven Pinion Bearing (inner race)
*2 Transfer Pinion Bearing Spacer
*3 Driven Pinion


Using a press, press out the driven pinion, rear transfer driven pinion bearing (inner race) and transfer pinion bearing spacer.

NOTICE:
·

Place a piece of cloth under the transfer case to prevent the driven pinion from dropping out of the rear transfer driven pinion bearing (inner race).

·

Use wooden blocks or similar objects under the case to keep it level.




Hide 41201K 23.REMOVE FRONT TRANSFER DRIVEN PINION BEARING

a.
C155208N03
2.792,0.573 2.635,0.573 2.635,0.573 2.51,1.26 false 2.833,0.5 3.177,0.688 0.344,0.188 10 false SST

Using SST and a press, remove the front transfer driven pinion bearing (inner race) from the transfer ring gear mounting case.

SST
09950-00020  

NOTICE:

Do not deform the cage of the front transfer driven pinion bearing (inner race) (when reusing the front transfer driven pinion bearing (inner race)).



b.
C052644

Using a brass bar and a hammer, tap the 2 positions shown in the illustration on the front transfer driven pinion bearing (outer race) to remove it from the transfer case.


Hide 33309H 24.REMOVE TRANSFER OUTPUT SHAFT WASHER

a.

Remove the transfer output shaft washer from the transfer case.


Hide 41301H 25.REMOVE RING GEAR MOUNTING CASE BEARING

a.

for RH side:

i.

Remove the ring gear mounting case bearing (outer race) from the transfer ring gear mounting case.


ii.
C298553C01
0.552,0.167 1.01,0.365 0.458,0.198 10 false SST 2.677,0.229 2.99,0.385 0.313,0.156 10 false *a 0.354,0.75 0.667,0.906 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the ring gear mounting case bearing (inner race) from the transfer ring gear mounting case.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00440)

NOTICE:
·

Use SST (09953-04020) after applying grease to its threads and tip.

·

Do not deform the cage of the ring gear mounting case bearing (inner race) (when reusing the ring gear mounting case bearing (inner race)).

·

Place identification marks on the left and right ring gear mounting case bearings to distinguish them (backside, teeth side). Then store them separately (when reusing the ring gear mounting case bearings).





b.

for LH side:

i.
C298554C01
2.135,0.146 2.448,0.302 0.313,0.156 10 false *a 0.188,0.792 0.5,0.948 0.313,0.156 10 false *b 0.396,0.167 0.854,0.365 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the ring gear mounting case bearing (inner race) from the transfer ring gear mounting case.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00400)

NOTICE:
·

Use SST (09953-04020) after applying grease to its threads and tip.

·

Do not deform the cage of the ring gear mounting case bearing (inner race) (when reusing the ring gear mounting case bearing (inner race)).

·

Place identification marks on the left and right ring gear mounting case bearings to distinguish them (backside, teeth side). Then store them separately (when reusing the ring gear mounting case bearings).




ii.
C055355

Using a brass bar and a hammer, tap the 2 positions shown in the illustration on the ring gear mounting case bearing (outer race) to remove it from the transfer case.


iii.

Remove the ring gear mounting case plate washer.



Hide 27.REMOVE RING GEAR

a.
C202225C01
1.583,1.188 1.125,1.802 1.125,1.802 1.552,1.323 false 0.958,1.792 1.146,1.969 0.188,0.177 10 false *a
*a Matchmark


Put matchmarks on the transfer ring gear mounting case and ring gear.


b.

Remove the 12 bolts from the ring gear.


c.
C202268

Using a plastic hammer, remove the ring gear to separate it from the transfer ring gear mounting case.

NOTICE:

Do not damage the ring gear teeth.



Hide 41319 28.INSPECT TRANSFER RING GEAR MOUNTING CASE

Hide 41201L 29.REMOVE REAR TRANSFER DRIVEN PINION BEARING (OUTER RACE)

a.
C052645

Using a brass bar and a hammer, tap the 2 positions shown in the illustration on the rear transfer driven pinion bearing (outer race) to remove it from the transfer case.