Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side)
RM3160E _58 Vehicle Interior _019712 SEAT _0108045 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.


PROCEDURE

Hide 72160 1.INSTALL REAR SEAT OUTER TRACK ASSEMBLY RH

a.

Install the rear seat outer track assembly RH to the rear seat track adjusting handle as shown in the illustration.

B387066

HINT:

Make sure the handle is straight when installing it, and check that it is centered.



Hide 72180C 2.INSTALL REAR SEAT INNER TRACK ASSEMBLY RH

a.

Install the rear seat inner track assembly RH to the rear seat track adjusting handle as shown in the illustration.

B387064

HINT:

Make sure the handle is straight when installing it, and check that it is centered.



Hide 71015 3.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

a.
B387056

Install the rear seat cushion frame sub-assembly RH with the 6 nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 71018 4.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY

a.
B362804

Using a T45 "TORX" socket wrench, install the rear seatback frame sub-assembly to the rear seat cushion frame sub-assembly with the 3 bolts as shown in the illustration.

Torque:
Torx Bolt : 42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Install the 2 bolts.

Torque:
Bolt : 64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 72704A 5.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.
B362802

Engage the 8 cable clamps to install the rear seat reclining control cable.


b.

Install 2 new wire harness clamps.


Hide 72210G 6.INSTALL NO. 1 REAR SEAT TRACK CONTROL CABLE ASSEMBLY

a.
B362801

Engage the 6 cable clamps to install the No. 1 rear seat track control cable assembly.


Hide 72704B 7.INSTALL NO. 2 REAR SEAT RECLINING CONTROL CABLE

a.
B362800

Engage the 2 cable clamps to install the No. 2 rear seat reclining control cable.


b.

Install 2 new wire harness clamps.


Hide 71629 8.INSTALL REAR SEAT CUSHION HINGE COVER

a.
B362799

Engage the 2 guides to install the rear seat cushion hinge cover.


Hide 72551A 9.INSTALL RECLINING HINGE COVER

a.
B362793

Engage the guide and 2 claws to install the reclining hinge cover.


Hide 71486C 10.INSTALL REAR SEAT HINGE COVER LH

a.
B362798

Engage the guide.


b.

Install the rear seat hinge cover LH with the screw.


Hide 72996E 11.INSTALL REAR NO. 1 SEAT INNER SHIELD COVER

a.
B362797

Engage the guide to install the rear No. 1 seat inner shield cover as shown in the illustration.


Hide 71833A 12.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

a.
B362795

Engage the clip and 5 claws to and install the rear No. 1 seat reclining cover RH.


b.
B362794

Engage the clamp.


Hide 71485 13.INSTALL REAR SEAT HINGE COVER

a.
B362792

Engage the 2 guides.


b.

Install the rear seat hinge cover with screw.


Hide 71829B 14.INSTALL REAR SEAT REAR CUSHION MOULDING

a.
B362772

Engage the guide and 6 claws.


b.

Install the rear seat rear cushion moulding with the screw.


Hide 73350A 15.INSTALL REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY

Hide 87510Q 18.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71078S 19.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.
B362808

Using hog ring pliers, install 9 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




b.
B362806

Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 8 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 20.INSTALL REAR SEATBACK COVER WITH PAD

a.
B362790

Engage the 2 hooks.


b.

w/ Seat Heater System:

i.
B362789C01
1.063,1.573 1.25,1.469 1.25,1.469 1,1.396 true 1.802,1.094 2.021,1.031 false 1.323,1.375 1.667,1.646 0.344,0.271 10 false *a 2.052,0.906 2.469,1.219 0.417,0.313 10 false *b
*a Clamp
*b Wire Harness Clamp


Engage the 2 clamps.


ii.

Install the wire harness clamp.



c.
B362791

Engage the 12 hooks.


d.
B362017

Using hog ring pliers, install the rear seatback cover with pad with 2 new hog rings.

NOTICE:
·

Be careful not to damage the rear seatback cover with pad.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad.




Hide 73373 21.INSTALL REAR SEAT SHOULDER BELT COVER

a.
B362780

Engage the 2 claws and 2 guides to install the rear seat shoulder belt cover.


Hide 73178A 22.INSTALL SEAT BELT ANCHOR COVER CAP

a.
B362779

Engage the 2 claws to install the seat belt anchor cover cap.


Hide 71931B 23.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.

for Center:

i.
B362784

Engage the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.



b.

for RH Side:

i.
B362785

Engage the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.



Hide 71865 24.INSTALL REAR NO. 1 SEAT COVER BEZEL

a.
B362011

Install the rear No. 1 seat cover bezel with the 3 screws.


Hide 72615A 25.INSTALL REAR SEATBACK LOCK STRIKER COVER

a.
B362009

Engage the 4 claws to install the 2 rear seatback lock striker covers.


Hide 72593C 26.INSTALL NO. 2 RECLINING REMOTE CONTROL LEVER KNOB

a.
B362005

Engage the claw to install the No. 2 reclining remote control lever knob as shown in the illustration.


Hide 71880A 27.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY

a.
B362778N01
0.885,2.833 1.177,3.125 0.292,0.292 10 false 1 1.26,2.917 1.552,3.208 0.292,0.292 10 false 2

Engage the 4 guides and 11 claws as indicated by the arrows, in the order shown in the illustration to install the rear seatback board carpet assembly.


Hide 72996 28.INSTALL REAR SEATBACK COVER RH

a.
B362775

Engage the 4 claws to install the rear seatback cover RH.


Hide 72996A 29.INSTALL REAR SEATBACK COVER

a.
B362776

Engage the 4 claws to install the rear seatback cover.


Hide 87510P 31.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71076S 32.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B362812

Using hog ring pliers, install 13 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




b.
B362810

Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with 8 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




Hide 33.INSTALL REAR SEAT CUSHION COVER WITH PAD

a.
B362774

Engage the 19 hooks to install the rear seat cushion cover with pad.


Hide 87501D 34.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

Hide 35.CONNECT REAR SEAT CUSHION HEATER HARNESS (w/ Seat Heater System)

a.
B364892

Engage the clamp to connect the rear seat cushion heater harness.


b.

Connect the connector.


Hide 36.CONNECT REAR SEATBACK HEATER HARNESS (w/ Seat Heater System)

a.
B364893C01
2.417,1.573 2.729,1.833 0.313,0.26 10 true *a 2.458,2.042 2.729,2.323 0.271,0.281 10 true *b 2.646,3.01 2.958,3.271 0.313,0.26 10 true *a
*a Clamp
*b Wire Harness Clamp


Engage the 2 clamps to connect the rear seatback heater harness.


b.

Install a new wire harness clamp.


c.

Connect the connector.


Hide 82194 37.INSTALL REAR SEAT WIRE (w/ Seat Heater System)

a.
B362752

Engage the 6 clamps to install the rear seat wire.


b.

Connect the connector.


Hide 82194 38.INSTALL REAR SEAT WIRE (w/ Seat Belt Warning System)

a.
B362755

Engage the 6 clamps to install the rear seat wire.


b.

Connect the connector.


Hide 73350A 39.CONNECT REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY

Hide 71485B 40.INSTALL REAR SEAT HINGE COVER

a.
B362788

Engage the 3 claws.


b.

Install the rear seat hinge cover with the screw.


Hide 72058A 41.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B361991

Engage the 2 cable clamps.


b.

Install a new wire harness clamp as shown in the illustration.

B368772


c.
B361989

Engage the 3 guides.


d.
B361987

Install the rear seat lock control lever sub-assembly with the 2 screws.


e.
B368732C01
1.344,1.104 1.438,1.323 1.438,1.323 1.615,1.125 false 2.448,1.115 2.76,1.271 0.313,0.156 10 false *a 1.385,1.365 1.719,1.615 0.333,0.25 10 false *b
*a Hook
*b Hog Ring


Using hog ring pliers, install 2 new hog rings.


f.

Engage the hook.


Hide 72615H 42.INSTALL REAR NO. 1 SEATBACK LOCK STRIKER COVER

a.
B361985

Engage the claw and guide to install the rear No. 1 seatback lock striker cover as shown in the illustration.


Hide 72525C 43.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE

a.
B361981

Install the No. 1 reclining adjuster release handle with the 3 screws.


Hide 71845D 44.INSTALL REAR SEAT COVER CAP

a.
B361980

Engage the 3 claws to install the rear seat cover cap.


Hide 71828B 46.INSTALL REAR SEAT REAR CUSHION MOULDING RH

a.
B362771

Engage the guide as shown in the illustration.


b.

Engage the clip and 9 claws to install the rear seat cushion moulding RH.


Hide 72087 47.INSTALL REAR NO. 1 SEAT CENTER ARMREST COVER

a.
B362769

Install the rear No. 1 seat center armrest cover to the rear No. 1 seat center armrest pad as shown in the illustration.


b.

Close the fastener as indicated by the arrows, in the order shown in the illustration.

B362767N01
2.573,2.021 2.938,2.344 0.365,0.323 10 false 1 5.646,2.417 6.01,2.74 0.365,0.323 10 false 2 6.854,1.24 7.063,1.563 0.208,0.323 10 false 2


Hide 72806D 48.INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY

a.
B362765

Engage the 2 guides and 2 claws to install the rear seat center armrest cup holder sub-assembly as shown in the illustration.


Hide 72831B 49.INSTALL NO. 1 REAR SEAT CENTER ARMREST PLATE

a.
B362763

Install the No. 1 rear seat center armrest plate to the rear seat center armrest assembly as shown in the illustration.


Hide 72830 50.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.

Engage the guide (A) as shown in the illustration.

B362761N01
1.354,1.76 1.771,2.104 0.417,0.344 10 false A 5.948,2.031 6.365,2.375 0.417,0.344 10 false B


b.

Engage the guide (B) and install the rear seat center armrest assembly and No. 2 rear seat center armrest plate with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72868 51.INSTALL CENTER ARMREST HINGE COVER RH

a.
B362759

Engage the guide and claw to install the center armrest hinge cover RH as shown in the illustration.