Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for LHD) › 2013.12–2016.11
RM3160E _54 Brake _019693 BRAKE SYSTEM (OTHER) _0108090 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY WITH WAY

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55701J 4.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 47220D 5.REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C292889C01
0.969,3.948 0.969,3.719 true 0.448,3.938 0.448,3.729 true 0.896,3.979 1.208,4.135 0.313,0.156 10 false *1 0.385,3.969 0.698,4.125 0.313,0.156 10 false *2
*1 Brake Master Cylinder Reservoir Assembly
*2 Reservoir Bracket


Disconnect the reservoir level switch connector and remove the bolt from the brake master cylinder reservoir assembly.


b.

Move the brake master cylinder reservoir assembly as shown in the illustration to disengage the 2 claws, and remove it.


Hide 47233 6.REMOVE RESERVOIR BRACKET

a.
C292891

Remove the 2 bolts and reservoir bracket.


Hide 82111 8.SEPARATE ENGINE ROOM MAIN WIRE

a.
C292895

Disengage the 5 clamps to separate the engine room main wire.


b.
C292893C01
2.323,0.833 1.823,0.833 true 2.354,2.99 1.854,2.99 true 1.521,1.313 1.021,1.313 true 2.365,0.75 2.563,0.906 0.198,0.156 10 true *a 0.833,1.229 1.031,1.406 0.198,0.177 10 true *b 2.375,2.906 2.573,3.063 0.198,0.156 10 true *a
*a Clamp
*b Pin


w/ Security Horn Assembly:

i.

Disconnect the connector from the security horn assembly.



c.

Remove the bolt.


d.

Disengage the 2 clamps and pin to separate the wire harness protector.


e.
C292894

Remove the 2 bolts.


f.

Disengage the 2 pins to separate the engine room relay block assembly.


Hide 82121 9.SEPARATE ENGINE WIRE

a.
C292892

Disengage the 3 clamps to separate the engine wire.


Hide 23820 10.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.
C292896

Slide the clip and disconnect the fuel vapor feed hose assembly.


Hide 44777 11.DISCONNECT NO. 1 VACUUM HOSE CONNECTOR (for 1AR-FE)

a.
C292897

Slide the clip and disconnect the union to check valve hose from the brake booster assembly.


b.
C292911

Remove the 2 nuts and separate the No. 1 vacuum hose connector.


Hide 44773F 12.DISCONNECT UNION TO CHECK VALVE HOSE (for 2GR-FE)

a.
C292897

Slide the clip and disconnect the union to check valve hose from the brake booster assembly.


Hide 88704 13.SEPARATE SUCTION HOSE SUB-ASSEMBLY

a.
C292898

Disengage the claw to release the piping clamp.


b.

Separate the suction hose sub-assembly from the piping clamp.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 14.SEPARATE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.
C292900

Remove the nut and separate the air conditioner tube and accessory assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 15.SEPARATE BRAKE LINE

a.
C292901C01
1.156,1.135 1.25,1.771 1.25,1.771 1.656,1.771 true 1.656,1.698 1.885,1.875 0.229,0.177 10 true *1
*1 Front No. 1 Brake Tube Way


Remove the bolt and separate the front No. 1 brake tube way.


b.

Disengage the brake tube clamp to separate the 3 brake lines.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not damage the clamp.




Hide 47101A 16.REMOVE BRAKE PEDAL RETURN SPRING

Hide 17.LOOSEN LOCK NUT

a.
C292902C01
2.083,1.031 2.438,0.583 2.438,0.583 3.083,0.583 true 2.229,1.208 2.563,1.51 2.563,1.51 3.042,1.51 true 3.115,0.5 3.365,0.688 0.25,0.188 10 false *1 3.052,1.427 3.281,1.646 0.229,0.219 10 false *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the lock nut of the brake master cylinder push rod clevis.


Hide 47264A 18.REMOVE PUSH ROD PIN

Hide 44610 19.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C292876

Remove the 4 nuts and push the brake booster assembly toward the engine compartment.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



b.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


c.

Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



Hide 44785 20.REMOVE BRAKE BOOSTER GASKET