Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD
RM3160E _56 Audio / Visual / Telematics _019700 AUDIO / VIDEO _0108136 RADIO ANTENNA CORD A

AUDIO / VIDEO  RADIO ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101J 1.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for Normal Roof)

HINT:

Butyl tape and adhesive tape are not available as supply parts. If these pieces of tape still have enough adhesion to secure the No. 2 antenna cord sub-assembly to the roof headlining assembly, reuse them. If the adhesive tape and/or the butyl tape is no longer sticky, apply new tape following the procedure below.


a.

Apply new butyl tape.

E288867C01
3.417,1.063 3.417,0.729 false 3.417,0.896 3.833,0.896 3.833,0.896 3.833,0.313 true 3.344,1.063 3.656,1.26 0.313,0.198 10 false *a
*a Marking - -
V100155

Butyl tape
V100136

Front


i.

Remove the old butyl tape from the roof headlining assembly.


ii.

Prepare the appropriate amount of new butyl tape.

HINT:

Be careful not to touch the adhesive surface.



iii.

Apply the butyl tape to the roof headlining assembly while aligning the tape with the markings on the roof headlining assembly.


iv.

Peel off the release paper from the butyl tape.



b.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the front of the roof headlining assembly.

E287561C02
2.354,0.76 2.438,0.51 true 4.365,2.427 4.448,2.177 true 2.271,0.76 2.583,0.917 0.313,0.156 10 true *a 4.323,2.438 4.635,2.594 0.313,0.156 10 true *b
*a Protrusion *b Adjustment Area
V100155

Adhesive Tape
V100143

Marking Tape
V100136

Front - -



c.

Engage each clamp.


d.

Connect the connector.


e.

Put the pieces of adhesive tape back to the positions shown in the illustration in order to secure the No. 2 antenna cord sub-assembly and washer hose to the roof headlining assembly.

HINT:
·

If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.

·

Align the marking tape on the No. 2 antenna cord sub-assembly with the protrusion of the roof headlining assembly, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.

·

Align the marking tape on the washer hose with the clamp of the No. 2 antenna cord sub-assembly.

·

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area shown in the illustration.




Hide 86101J 2.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for Sliding Roof)

HINT:

Butyl tape and adhesive tape are not available as supply parts. If these pieces of tape still have enough adhesion to secure the No. 2 antenna cord sub-assembly to the roof headlining assembly, reuse them. If the adhesive tape and/or the butyl tape is no longer sticky, apply new tape following the procedure below.


a.

Apply new butyl tape.

E287569C01
3.333,1.063 3.333,0.729 false 3.333,0.896 3.667,0.896 3.667,0.896 3.667,0.313 true 3.25,1.073 3.563,1.271 0.313,0.198 10 false *a
*a Marking - -
V100155

Butyl tape
V100136

Front


i.

Remove the old butyl tape from the roof headlining assembly.


ii.

Prepare the appropriate amount of new butyl tape.

HINT:

Be careful not to touch the adhesive surface.



iii.

Apply the butyl tape to the roof headlining assembly while aligning the tape with the markings on the roof headlining assembly.


iv.

Peel off the release paper from the butyl tape.



b.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the front of the roof headlining assembly.

E287568C02
5.323,4.49 5.375,4.271 true 2.333,0.833 2.448,0.635 true 4.552,2.448 4.667,2.25 true 5.198,4.5 5.51,4.698 0.313,0.198 10 true *A 2.25,0.833 2.563,1.031 0.313,0.198 10 true *a 4.448,2.448 4.76,2.646 0.313,0.198 10 true *b
*A w/ DAB Function - -
*a Protrusion *b Adjustment Area
V100155

Adhesive Tape
V100143

Marking Tape
V100136

Front - -



c.

Engage each clamp.


d.

Connect each connector.


e.

Put the pieces of adhesive tape back to the positions shown in the illustration in order to secure the No. 2 antenna cord sub-assembly and washer hose to the roof headlining assembly.

HINT:
·

If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.

·

Align the marking tape on the No. 2 antenna cord sub-assembly with the protrusion of the roof headlining assembly, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.

·

Align the marking tape on the washer hose with the clamp of the No. 2 antenna cord sub-assembly.

·

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area shown in the illustration.




Hide 3.INSTALL ROOF HEADLINING ASSEMBLY

Hide 86101 4.INSTALL ANTENNA CORD SUB-ASSEMBLY

a.

Engage the 4 clamps to install the antenna cord sub-assembly.


Hide 55846A 5.INSTALL NO. 4 HEATER TO REGISTER DUCT (for LHD)

Hide 55843A 6.INSTALL NO. 1 HEATER TO REGISTER DUCT (for RHD)

Hide 7.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY