Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL INJECTOR
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0108296 FUEL INJECTOR A

1AR-FE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17705 5.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


a.
A292804

Disengage the claw and remove the No. 1 fuel pipe clamp.


b.

Disconnect the fuel tube sub-assembly from the fuel pipe.

i.
A296959C04
2.385,2.875 2.313,2.875 2.313,2.875 2.198,3.469 false 1.792,3.271 1.719,2.865 1.719,2.865 1.635,2.865 false 0.854,4.156 0.854,3.813 false 2.885,3.438 3.156,4.073 3.156,4.073 2.875,3.802 false 1.99,3.833 2.26,4.198 2.26,4.198 1.969,3.417 false 1.25,4.229 1.563,4.229 1.563,4.229 1.563,3.781 false 1.396,4.219 1.396,3.781 false 1.635,2.448 1.563,2.448 1.563,2.448 1.427,1.635 false 2.427,2.802 2.74,2.958 0.313,0.156 10 false *d 1.427,2.792 1.75,3.063 0.323,0.271 10 false *c 0.792,4.208 1.104,4.365 0.313,0.156 10 false *e 1.073,4.146 1.385,4.302 0.313,0.156 10 false *b 2.25,4.219 2.563,4.375 0.313,0.156 10 false *a 3.188,4.094 3.427,4.25 0.24,0.156 10 false *a 1.698,2.365 2.01,2.521 0.313,0.156 10 false *1
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
*e Nylon Tube
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Do not forcibly bend, twist or turn the nylon tube.




iii.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Disengage the clamp to disconnect the fuel tube sub-assembly from the fuel hose clamp.


Hide 17650 7.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 82121 8.DISCONNECT ENGINE WIRE

a.
A252630

Disconnect the 4 fuel injector assembly connectors, throttle body with motor assembly connector and sensor wire connector.


b.

Remove the 2 bolts and separate the 2 wire harness brackets from the intake manifold.


c.

Disengage the clamp to disconnect the engine wire.


Hide 23814B 9.REMOVE FUEL DELIVERY PIPE

a.
A252631

Remove the 2 bolts and fuel delivery pipe with the 4 fuel injector assemblies.

NOTICE:

Do not drop the fuel injector assemblies when removing the fuel delivery pipe.



b.
A211217C01
1.417,1.031 1.729,1.188 0.313,0.156 10 true *1 1.948,1.781 2.26,1.938 0.313,0.156 10 true *2 2.24,0.646 2.552,0.802 0.313,0.156 10 true *1 2.344,1.594 2.656,1.75 0.313,0.156 10 true *2 2.708,1.396 3.021,1.552 0.313,0.156 10 true *2 3.073,1.188 3.385,1.344 0.313,0.156 10 true *2
*1 Fuel Delivery Spacer
*2 Injector Vibration Insulator


Remove the 2 fuel delivery spacers from the cylinder head sub-assembly.


c.

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 23250 10.REMOVE FUEL INJECTOR ASSEMBLY

a.
A314716

Pull the 4 fuel injector assemblies out of the fuel delivery pipe.


b.

Remove the O-ring from each fuel injector assembly.


c.

For reinstallation, attach a tag or label with the corresponding cylinder number to each fuel injector assembly.

NOTICE:

Protect the fuel injector assemblies by covering them with plastic bags.