Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL PRESSURE PULSATION DAMPER
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0108298 FUEL PRESSURE PULSATION DAMPER A

1AR-FE FUEL  FUEL PRESSURE PULSATION DAMPER  INSTALLATION  


PROCEDURE

Hide 23270 1.INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY

a.
A196015C01
2.583,1.615 2.771,1.615 2.771,1.615 2.99,1.073 false 2.375,1.542 2.563,1.75 0.188,0.208 10 *1
*1 O-ring


Apply a light coat of gasoline or spindle oil to a new O-ring.


b.

Install the O-ring to the fuel pressure pulsation damper assembly.


c.

Install the fuel pressure pulsation damper assembly to the fuel delivery pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure that the O-ring is not cracked or jammed when installing the fuel pressure pulsation damper assembly.



Hide 23901 2.CONNECT FUEL TUBE SUB-ASSEMBLY

A314724C01
0.573,4.198 0.573,3.948 false 0.688,3.031 0.844,3.031 0.844,3.031 1.052,3.479 false 1.24,3.021 1.563,3.021 1.563,3.021 1.563,3.458 false 1.354,3.469 1.354,3.021 false 2.24,3.344 2.427,2.938 2.427,2.938 2.604,2.938 false 2.927,4.177 2.927,3.896 false 2.198,4.344 2.198,4.125 false 0.49,2.948 0.802,3.104 0.313,0.156 10 false *1 2.667,2.854 2.979,3.01 0.313,0.156 10 false *a 1.052,2.938 1.365,3.094 0.313,0.156 10 false *b 0.5,4.219 0.813,4.375 0.313,0.156 10 false *c 2.115,4.365 2.427,4.521 0.313,0.156 10 false *d 2.865,4.198 3.177,4.354 0.313,0.156 10 false *e
*1 Fuel Tube Sub-assembly
*a Retainer
*b O-ring
*c Nylon Tube
*d Fuel Tube Connector
*e Fuel Pipe


a.

Connect the fuel tube sub-assembly to the fuel delivery pipe.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.

Align the fuel tube connector with the fuel pipe, and push the fuel pipe into the fuel tube connector until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



b.

Engage the 2 claws to install a new No. 2 fuel pipe clamp.


Hide 17705 3.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 6.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY