Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL PRESSURE PULSATION DAMPER
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0108298 FUEL PRESSURE PULSATION DAMPER A

1AR-FE FUEL  FUEL PRESSURE PULSATION DAMPER  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17705 5.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 23901 6.REMOVE FUEL TUBE SUB-ASSEMBLY

NOTICE:
·

Do not forcibly bend, kink or twist the fuel tube sub-assembly.

·

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.



a.
A315515C01
2.594,1.135 2.688,1.365 2.688,1.365 2.771,1.135 false 2.615,1.396 2.927,1.552 0.313,0.156 10 false *a
*a Claw


Disengage the 2 claws to remove the No. 2 fuel pipe clamp.

NOTICE:

Do not reuse the No. 2 fuel pipe clamp.



b.

Disconnect the fuel tube sub-assembly from the fuel delivery pipe.

i.
A062165N01
1.979,0.719 2.49,1.635 2.49,1.635 2.021,1.854 true 2.531,1.552 2.844,1.729 0.313,0.177 10 SST

Install SST (fuel hose puller) to the fuel tube connector as shown in the illustration.

SST
09268-21011  


ii.
A284030C16
2.167,1.344 2.448,1.771 2.448,1.771 2.635,1.771 false 0.708,1.24 1.021,1.396 0.313,0.156 10 false *a 2.74,1.688 3.208,1.948 0.469,0.26 10 false SST
*a Retainer (4 places)


Turn SST (fuel hose puller), align the retainers inside the fuel tube connector with the SST (fuel hose puller) chamfers and insert SST (fuel hose puller) into the fuel tube connector.


iii.

Mount the retainer of the fuel tube connector onto the chamfered part of SST (fuel hose puller).


iv.
A076220C14
2.26,1.573 2.26,1.875 false 0.594,1.375 0.594,1.708 false 1.396,0.875 1.125,0.438 1.125,0.438 1.594,0.875 false 2.917,1.323 2.917,1.531 false 2.156,0.771 2.281,0.438 2.281,0.438 2.417,0.438 false 0.542,0.448 0.76,0.448 0.76,0.448 1.083,0.917 false 0.948,0.323 1.25,0.563 0.302,0.24 10 false *b 2.479,0.354 2.833,0.563 0.354,0.208 10 false *a 2.844,1.573 3.073,1.771 0.229,0.198 10 false *e 0.51,1.74 0.719,1.969 0.208,0.229 10 false *c 2.177,1.917 2.385,2.115 0.208,0.198 10 false *d 0.354,0.375 0.563,0.604 0.208,0.229 10 false *1
*1 Fuel Tube Sub-assembly
*a Retainer
*b O-ring
*c Nylon Tube
*d Fuel Tube Connector
*e Fuel Pipe


Slide SST (fuel hose puller) and the fuel tube connector together until they make a "click" sound, and then disconnect the fuel tube sub-assembly.

NOTICE:
·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Do not forcibly bend, twist or turn the nylon tube.





Hide 23270 7.REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY

a.
A196014

Remove the 2 bolts and fuel pressure pulsation damper assembly from the fuel delivery pipe.


b.

Remove the O-ring from the fuel pressure pulsation damper assembly.