Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL INJECTOR › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019664 2GR-FE FUEL _0108302 FUEL INJECTOR A

2GR-FE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17190 4.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 23292D 5.REMOVE FUEL HOSE PROTECTOR

a.
A313763C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, nut and fuel hose protector.


Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


a.
A315510

Remove the No. 2 fuel pipe clamp from the fuel tube connector.


b.

Check that there is no dirt or other foreign matter around the fuel tube connector before disconnecting it. Clean the joint if necessary.


c.
A315513C01
1.115,4.073 1.115,3.781 false 2.01,4.208 2.01,3.719 false 1.833,4.208 2.177,4.208 2.177,4.208 2.177,3.708 false 2.313,2.854 2.448,2.854 2.448,2.854 2.583,3.26 false 2.823,3.469 2.938,2.979 2.938,2.979 3.063,2.979 false 2.573,4.281 2.573,3.792 false 2.125,2.771 2.438,2.927 0.313,0.156 10 false *c 1.052,4.094 1.365,4.25 0.313,0.156 10 false *e 1.656,4.115 1.969,4.271 0.313,0.156 10 false *b 3.115,2.885 3.427,3.042 0.313,0.156 10 false *d 2.5,4.271 2.813,4.427 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
*e Nylon Tube
V100135

Pinch
V100136

Pull


Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

i.

Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Do not forcibly bend, twist or turn the nylon tube.




iii.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



Hide 23807 7.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A137341

Disconnect the 6 fuel injector assembly connectors.


b.
A129471

Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injector assemblies.

NOTICE:

Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



c.
A292481

Remove the 6 injector vibration insulators from the intake manifold.


Hide 23250 8.REMOVE FUEL INJECTOR ASSEMBLY

a.
A129473

Pull the 6 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

NOTICE:

If the fuel injector assemblies are to be reused, reinstall them to the same cylinder they came from.



b.
A129475C03
2.875,1.438 2.875,1.583 false 2.833,1.625 3.25,1.979 0.417,0.354 10 *1
*1 O-ring


Remove the O-ring from each fuel injector assembly.


c.

For reinstallation, attach a tag or label with the corresponding cylinder number to each fuel injector assembly.

NOTICE:

Protect the fuel injector assemblies by covering them with plastic bags.