Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL TANK › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019664 2GR-FE FUEL _0108307 FUEL TANK A

2GR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 2.DRAIN FUEL

Hide 51206A 3.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (for 2WD)

Hide 51206A 4.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (for AWD)

Hide 58167A 5.REMOVE FRONT CENTER FLOOR COVER

a.
A314680C01
0,0 0,0 false
V100135

Screw
V100136

Nut


Remove the 2 screws and nut.


b.

Disengage the 4 clips to remove the front center floor cover.


Hide 77765 6.REMOVE CHARCOAL CANISTER PROTECTOR

Hide 77606 7.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A314681

Remove the 4 clips, 7 nuts and No. 1 fuel tank protector sub-assembly.


Hide 77209F 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A314682C01
0.396,2.365 0.51,2.365 0.51,2.365 0.604,2.167 false 0.427,2.865 0.594,2.865 0.594,2.865 0.708,3.302 false 0.781,3.208 0.99,2.771 0.99,2.771 1.125,2.771 false 0.365,4.104 0.365,3.958 0.365,3.958 0.646,3.667 false 0.99,4.24 1.323,4.24 1.323,4.24 1.323,3.719 false 1.156,4.24 1.156,3.729 false 0.229,2.271 0.542,2.427 0.313,0.156 10 false *a 0.813,4.156 1.125,4.313 0.313,0.156 10 false *b 1.156,2.688 1.469,2.844 0.313,0.156 10 false *c 0.292,4.135 0.604,4.292 0.313,0.156 10 false *d 0.24,2.771 0.552,2.927 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
V100135

Pull Out
V100136

Pull Off


Disconnect the fuel tank main tube sub-assembly.

i.

Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.

NOTICE:
·

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.

·

Be sure to disconnect the fuel tube connector by hand.




ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.




iii.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



Hide 77404A 9.DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.
A315521C01
2.396,0.729 2.469,0.49 2.469,0.49 2.552,0.49 false 2.583,0.406 2.896,0.563 0.313,0.156 10 false *a
*a Retainer
V100135

Pull
V100136

Pull Out
V100137

Pull Off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tank vent hose sub-assembly.

NOTICE:
·

Remove any dirt or foreign matter on the fuel tank vent hose sub-assembly before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tank vent hose sub-assembly has an O-ring that seals the pipe.

·

Only disconnect the fuel tank vent hose sub-assembly by hand.

·

Do not forcibly bend, twist or turn the fuel tank vent hose sub-assembly.




Hide 10.DISCONNECT FUEL TANK BREATHER TUBE

a.
A314684

Loosen the clamp, then disconnect the fuel tank breather tube from the fuel pipe.


Hide 77100 11.REMOVE FUEL TANK ASSEMBLY

a.
A314685C01
1.167,0.49 1.854,0.49 false 0.708,1.219 1.25,1.219 false 0.479,1.125 0.667,1.302 0.188,0.177 10 true *1 0.948,0.406 1.146,0.583 0.198,0.177 10 true *2
*1 Fuel Tank To Filler Pipe Hose
*2 Fuel Tank To Filler Pipe Sub-assembly


Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank to filler pipe sub-assembly.


b.
A314687

Remove the bolt, nut and rear fuel tank bracket LH.


c.
A314691

Remove the nut.


d.
A314688

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, place the fuel tank assembly horizontally.



e.

Remove the 4 bolts, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH.


f.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Do not drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the other surrounding parts.




Hide 77113B 12.REMOVE FUEL TANK SIDE PLATE

a.
A314690C01
1.104,0.792 1.281,0.948 0.177,0.156 10 true *1 0.573,1.115 0.74,1.281 0.167,0.167 10 true *2
*1 Fuel Tank Band Pin
*2 Fuel Tank Cushion


Remove the fuel tank band pin, fuel tank cushion and fuel tank side plate from the fuel tank assembly.


Hide 13.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A314692C01
0.729,0.802 1.083,0.802 false 1.146,0.719 1.458,0.875 0.313,0.156 10 false *1
*1 Fuel Tank Main Tube Sub-assembly


Disengage the 3 claws to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77213B 14.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A314693

Loosen the clamp, then remove the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77608C 15.REMOVE FUEL TANK CUSHION SET

a.
A314695C01
0.438,0.302 0.563,0.302 0.563,0.302 0.667,0.448 false 0.406,1.375 0.552,1.375 0.552,1.375 0.635,1.208 false 0.427,2.323 0.594,2.323 false 0.438,3.125 0.552,3.125 0.552,3.125 0.635,2.938 false 0.26,0.219 0.573,0.375 0.313,0.156 10 false *1 0.24,1.292 0.552,1.448 0.313,0.156 10 false *2 0.25,2.24 0.563,2.396 0.313,0.156 10 false *1 0.26,3.042 0.573,3.198 0.313,0.156 10 false *2
*1 Fuel Tank Cushion Set
*2 No. 5 Fuel Tank Cushion


Remove the 2 fuel tank cushion sets and 2 No. 5 fuel tank cushions from the fuel tank assembly.


Hide 77158A 16.REMOVE TANK SUCTION TUBE SUPPORT

a.
A314697

Remove the tank suction tube support from the fuel tank assembly.