When the back door closer system does not operate, one of the following may be the cause: 1) improper fit of the back door or a foreign object stuck in the back door, 2) the multiplex network door ECU has not been initialized, 3) a malfunction in the multiplex network door ECU power source circuit, 4) a malfunction in the back door lock assembly circuit, or 5) a multiplex network door ECU malfunction.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC B2250 is output | B |
| DTC B2251 is output | C |
A
B
C
Check if the back door can be fully closed by hand.
| Result | Proceed to |
|---|---|
| The back door can be closed normally | A |
| The back door cannot be closed normally | B |
A
B
Perform the initialization of the multiplex network door ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check the back door closer system operation.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| The back door closer system operates normally | A |
| The back door closer system operates not normally | B |
A
B
| *a | Front view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the X6 and X7 multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X7-7 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X6-1 (ECUB) - Body ground | Always | 11 to 14 V |
| X7-8 (B) - Body ground | Always | 11 to 14 V |
| X6-7 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| X6-7 (IG) - Body ground | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door lock assembly.
Inspect the back door lock assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the X19 back door lock assembly connector.
Disconnect the X6 and X7 multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X19-1 (M+) - X7-10 (DC+) | Always | Below 1 Ω |
| X19-2 (M-) - X7-9 (DC-) | Always | Below 1 Ω |
| X19-3 (CTY) - X6-19 (FUL) | Always | Below 1 Ω |
| X19-5 (CLS) - X6-21 (HAF) | Always | Below 1 Ω |
| X19-6 (OPN) - X6-24 (POS) | Always | Below 1 Ω |
| X19-4 (E) - Body ground | Always | Below 1 Ω |
| X19-1 (M+) or X7-10 (DC+) - Body ground | Always | 10 kΩ or higher |
| X19-2 (M-) or X7-9 (DC-) - Body ground | Always | 10 kΩ or higher |
| X19-3 (CTY) or X6-19 (FUL) - Body ground | Always | 10 kΩ or higher |
| X19-5 (CLS) or X6-21 (HAF) - Body ground | Always | 10 kΩ or higher |
| X19-6 (OPN) or X6-24 (POS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG