Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109579 CYLINDER HEAD GASKET A

2GR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 11104A 1.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13801 2.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 24 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 3.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 24 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 4.REMOVE VALVE STEM CAP

a.

Remove the 24 valve stem caps.


Hide 11101 6.REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

a.
A129712N07
2.854,0.083 2.99,0.24 0.135,0.156 10 true 3 2.073,0.083 2.208,0.24 0.135,0.156 10 true 5 1.313,0.083 1.448,0.24 0.135,0.156 10 true 7 0.552,0.083 0.688,0.24 0.135,0.156 10 true 2 2.896,1.688 3.031,1.844 0.135,0.156 10 true 1 2.073,1.688 2.208,1.844 0.135,0.156 10 true 8 1.313,1.688 1.448,1.844 0.135,0.156 10 true 6 0.479,1.688 0.615,1.844 0.135,0.156 10 true 4

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and plate washers.

NOTICE:
·

Be careful not to drop plate washers into the cylinder head sub-assembly RH.

·

Warpage or cracking of the cylinder head sub-assembly RH may result from removing bolts in the incorrect order.



HINT:

Arrange the removed parts in the correct order.



b.

Remove the cylinder head sub-assembly RH.


Hide 11115 7.REMOVE CYLINDER HEAD GASKET RH

a.

Remove the cylinder head gasket RH.


Hide 11102 8.REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

a.
A129710E01
0.141,0.77 0.275,0.926 0.133,0.156 10 2 0.073,1.389 0.206,1.545 0.133,0.156 10 1

Uniformly loosen and remove the 2 cylinder head set bolts in several steps in the order shown in the illustration.


b.
A129711N06
0.781,0.292 0.917,0.448 0.135,0.156 10 true 1 1.469,0.292 1.604,0.448 0.135,0.156 10 true 8 2.177,0.292 2.313,0.448 0.135,0.156 10 true 6 2.917,0.292 3.052,0.448 0.135,0.156 10 true 4 0.719,1.844 0.854,2 0.135,0.156 10 true 3 1.479,1.844 1.615,2 0.135,0.156 10 true 5 2.198,1.844 2.333,2 0.135,0.156 10 true 7 2.938,1.844 3.073,2 0.135,0.156 10 true 2

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and plate washers.

NOTICE:
·

Be careful not to drop plate washers into the cylinder head sub-assembly LH.

·

Warpage or cracking of the cylinder head sub-assembly LH may result from removing bolts in the incorrect order.



HINT:

Arrange the removed parts in the correct order.



c.

Remove the cylinder head sub-assembly LH.


Hide 11116 9.REMOVE CYLINDER HEAD GASKET LH

a.

Remove the cylinder head gasket LH.