Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE UNIT › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109583 ENGINE UNIT A

2GR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly and oil filler cap gasket.


Hide 12101A 3.REMOVE OIL PAN DRAIN PLUG

a.
A129654

Remove the oil pan drain plug and oil pan drain plug gasket.


Hide 12204 4.REMOVE VENTILATION VALVE SUB-ASSEMBLY

a.
A129655

Remove the ventilation valve sub-assembly.


Hide 11401M 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side of Bank 1)

Hide 11401M 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 1)

Hide 11401M 7.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side of Bank 2)

Hide 11401M 8.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 2)

Hide 9.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1)

Hide 10.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)

Hide 11.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2)

Hide 12.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)

Hide 11401G 13.REMOVE CRANKSHAFT POSITION SENSOR

Hide 15771 14.REMOVE NO. 1 OIL PIPE

a.
A314828C01
1.302,0.74 1.469,0.906 0.167,0.167 10 true *a 1.948,1.948 2.115,2.115 0.167,0.167 10 true *a
*a Oil Pipe Union


Remove the 2 oil pipe unions, 3 gaskets and No. 1 oil pipe.


b.

Remove the oil control valve filter LH.


Hide 15771M 15.REMOVE OIL PIPE

a.
A200607C07
1.74,0.75 1.906,0.906 0.167,0.156 10 true *a 1.573,1.771 1.74,1.927 0.167,0.156 10 true *a 2.344,1.135 2.51,1.292 0.167,0.156 10 false *b
*a Oil Pipe Union
*b Bolt


Remove the bolt.


b.

Remove the 2 oil pipe unions, 3 gaskets and oil pipe.


c.

Remove the oil control valve filter RH.


Hide 11415 16.REMOVE TAPER SCREW PLUG

HINT:

Perform this operation only when a taper screw plug is installed.


a.
A292824

Remove the taper screw plug from the cylinder block sub-assembly.


Hide 11415 17.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A292825C01
0.052,0.042 0.417,0.365 0.365,0.323 12 false *A 0.083,1.615 0.552,2.031 0.469,0.417 12 false *B
*A for Bank 1
*B for Bank 2


a.

for Bank 1:

i.

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


ii.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.



b.

for Bank 2:

HINT:

Perform this operation only when a cylinder block water drain cock sub-assembly is installed.


i.

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


ii.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.



Hide 15620 18.REMOVE OIL FILTER CAP ASSEMBLY

Hide 15710 20.REMOVE OIL COOLER ASSEMBLY

Hide 15781 21.REMOVE NO. 1 OIL COOLER BRACKET

a.
A268434

Remove the 3 bolts, 3 nuts, and oil cooler pipe with No. 1 oil cooler bracket and gasket.


b.
A268435C06
2.833,0.448 3.146,0.604 0.313,0.156 10 false *a 2.563,1.219 2.875,1.375 0.313,0.156 10 false *a 2.917,1.052 3.229,1.25 0.313,0.198 10 false *b
*a Nut
*b Bolt


Remove the bolt, 2 nuts, No. 1 oil cooler bracket, and gasket.


c.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


d.

Using an E7 "TORX" socket wrench, remove the stud bolt.


Hide 11452 22.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A210128

Remove the engine oil level dipstick guide.


b.
A171897

Remove the O-ring.


Hide 12315 23.REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH

a.
A311541

Remove the 6 bolts and No. 1 front engine mounting bracket LH.


b.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


Hide 16331 24.REMOVE WATER OUTLET

a.
A129676C02
0.781,1.521 0.969,1.708 0.188,0.188 10 true *a 0.844,0.417 1.031,0.604 0.188,0.188 10 true *a 2.49,0.396 2.677,0.583 0.188,0.188 10 true *a 2.615,1.448 2.792,1.615 0.177,0.167 10 true *a 1.521,1.521 1.698,1.698 0.177,0.177 10 true *b 1.896,1.521 2.073,1.688 0.177,0.167 10 true *b
*a Nut
*b Bolt


Remove the 2 bolts, 4 nuts and water outlet.


b.
A129677

Remove the 2 gaskets and O-ring.


Hide 11201 25.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A129679C06
1.906,1.177 1.771,1.385 false 1.604,1.385 1.781,1.542 0.177,0.156 10 false *1
*1 Seal Washer


Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A129699

Remove the 3 gaskets.


Hide 11202 26.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A314829C01
1.75,1.042 1.948,0.865 false 2.458,0.896 2.979,1.125 false 2.292,0.76 2.49,0.917 0.198,0.156 10 false *a 1.938,0.708 2.135,0.865 0.198,0.156 10 false *1
*1 Seal Washer
*a Baffle Plate


Remove the 12 bolts, seal washer, cylinder head cover sub-assembly LH and No. 2 cylinder head cover gasket.

NOTICE:

The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the cylinder head cover sub-assembly LH.



b.
A129705

Remove the 3 gaskets.


Hide 16323 27.REMOVE WATER INLET HOUSING

a.
A129673

Remove the 2 nuts, water inlet and thermostat.


b.

Remove the gasket.


c.

Remove the 2 stud bolts.


d.

Disconnect the No. 1 water by-pass hose from the water inlet housing.


e.
A134879C07
0.938,1.344 1.542,1.729 0.604,0.385 10 false *a 1.958,0.573 2.365,0.896 0.406,0.323 10 false *b 1.854,1.927 2.281,2.177 0.427,0.25 10 true *b
*a Nut
*b Bolt


Remove the drain cock plug.


f.

Remove the drain cock assembly.


g.

Remove the 2 bolts, nut, and water inlet housing.


h.
A129675

Remove the 2 O-rings.


Hide 12102A 28.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A129680C06
2.458,0.5 2.635,0.667 0.177,0.167 10 true *a 0.323,1.656 0.5,1.823 0.177,0.167 10 false *a
*a Nut


Remove the 16 bolts and 2 nuts.


b.
A120816

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



c.

Using an E6 "TORX" socket wrench, remove the 2 stud bolts from the oil pan sub-assembly.


Hide 15104 29.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A129681C07
2.406,1.281 2.573,1.448 0.167,0.167 10 false *a 0.969,1.865 1.135,2.031 0.167,0.167 10 true *b 1.073,0.667 1.24,0.833 0.167,0.167 10 true *b
*a Bolt
*b Nut


Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.


b.

Using an E6 "TORX" socket wrench, remove the 2 stud bolts from the oil pan sub-assembly.


Hide 12101 30.REMOVE OIL PAN SUB-ASSEMBLY

a.

Remove the oil pan sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.

Using an E8 "TORX" socket wrench, remove the 4 stud bolts.

A376289C01
0.219,0.042 6.948,2.25 6.729,2.208 0.219,2.302 6.948,4.51 6.729,2.208 0.271,0.104 0.604,0.313 0.333,0.208 12 false *A 0.281,2.438 0.656,2.698 0.375,0.26 12 false *B 1.521,0.104 1.833,0.26 0.313,0.156 10 false *a 5.5,0.094 5.813,0.25 0.313,0.156 10 false *b 1.479,4.75 1.792,4.906 0.313,0.156 10 false *c 3.094,2.396 3.406,2.552 0.313,0.156 10 false *b
*A Type A *B Type B
*a Timing Chain Cover Sub-assembly Side *b Cylinder Block Sub-assembly Bottom Side
*c Oil Pan Sub-assembly LH Side - -



Hide 12121 31.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A129685

Remove the 7 bolts and No. 1 oil pan baffle plate.


Hide 11381 32.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A129686

Remove the 6 bolts.


b.
A304100C06
0.646,1.271 1.26,1 true 0.479,1.198 0.792,1.396 0.313,0.198 10 false *a
*a Protective Tape
V100135

Pry


Using a screwdriver, pry out the rear engine oil seal retainer.

NOTICE:

Be careful not to damage the rear engine oil seal retainer.


HINT:

Tape the screwdriver tip before use.



Hide 11381A 33.REMOVE REAR ENGINE OIL SEAL

a.
A131834C04
0.99,1.75 0.635,1.958 0.635,1.958 2.344,2.021 false 1.49,1.354 0.844,0.635 false 0.646,0.531 1.031,0.813 0.385,0.281 10 false *a 0.417,1.865 0.781,2.115 0.365,0.25 10 false *b
*a Protective Tape
*b Wooden Block


Place the rear engine oil seal retainer on wooden blocks.


b.

Using a screwdriver and hammer, tap out the rear engine oil seal.

NOTICE:

Be careful not to damage the rear engine oil seal retainer.


HINT:

Tape the screwdriver tip before use.



Hide 16100 34.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11302 35.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A129689C03
2.51,1.719 2.74,1.896 0.229,0.177 10 false *a 0.74,1.927 0.906,2.083 0.167,0.156 10 false *a
*a Nut


Remove the 15 bolts and 2 nuts shown in the illustration.


b.
A129690C06
0.5,4.135 1.344,4.427 1.344,4.427 2.917,4.083 false 1.906,0.646 0.729,2.24 0.729,2.24 0.729,1.125 false 2.438,0.969 0.729,2.24 false 0.583,2.292 0.76,2.49 0.177,0.198 10 false *a 1.25,4.469 1.427,4.667 0.177,0.198 10 false *a
*a Protective Tape


Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.

Remove the 4 bolts, timing chain cover plate and timing chain cover plate gasket.


d.
A128006

Remove the gasket.


Hide 11301C 36.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 37.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily tighten the crankshaft pulley bolt.


b.
A205165C10
0.635,0.615 0.635,1.417 0.635,1.417 1.594,0.938 false 0.5,0.208 1.281,0.125 false 2.396,1.438 2.604,1.646 false 1.302,0.031 1.479,0.198 0.177,0.167 10 true *b 0.542,1.458 0.719,1.625 0.177,0.167 10 true *c 2.583,1.677 2.76,1.844 0.177,0.167 10 true *a
*a Sensor Plate
*b Center Line
*c Timing Mark


Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the center line of the block bore (Bank 1) (TDC/compression).


c.
A120646C02
0.99,3.292 1.74,4.125 1.74,4.125 2.396,3.375 true 1.01,3.844 1.74,4.135 1.74,4.135 2.365,3.677 true 1.125,0.635 1.917,1.406 1.917,1.406 2.688,0.708 true 1.104,1.063 1.917,1.417 1.917,1.417 2.677,1.25 true 1.813,1.438 2.01,1.615 0.198,0.177 10 true *a 1.688,4.177 1.906,4.365 0.219,0.188 10 true *a
*a Timing Mark


Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned with the timing marks of the camshaft bearing caps as shown in the illustration.

If not aligned, turn the crankshaft 1 revolution (360°) clockwise and align the timing marks as above.


Hide 13540 38.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A124589C12
1.063,1.104 1.448,1.76 1.448,1.76 2.656,1.177 false 2.667,1.729 2.875,1.729 false 1.146,0.875 0.865,0.156 false 2.823,0.875 2.552,0.146 false 0.656,0.073 0.823,0.25 0.167,0.177 10 true *a 1.344,1.802 1.521,1.958 0.177,0.156 10 true *b 2.885,1.646 3.063,1.823 0.177,0.177 10 true *c 2.354,0.073 2.521,0.25 0.167,0.177 10 true *a
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


Turn the stopper plate clockwise to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Turn the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.
A095165

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 39.REMOVE CHAIN TENSIONER SLIPPER

a.

Remove the chain tensioner slipper.


Hide 13506 40.REMOVE CHAIN SUB-ASSEMBLY

a.
A211711C05
0.438,0.156 0.646,0.146 false 2.417,1.5 2.625,1.708 false 0.51,0.688 0.729,1.521 0.729,1.521 1.594,0.927 false 0.229,0.26 0.458,0.427 0.229,0.167 10 true 10° 0.667,0.063 0.844,0.24 0.177,0.177 10 false *b 0.646,1.552 0.813,1.729 0.167,0.177 10 true *c 2.573,1.729 2.75,1.917 0.177,0.188 10 true *a
*a Sensor Plate
*b Center Line
*c Timing Mark


Turn the crankshaft 10° counterclockwise to loosen the chain sub-assembly of the crankshaft timing sprocket.


b.

Remove the crankshaft pulley bolt.


c.
A134890

Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.


d.
A314809C01
0.104,0.083 0.552,0.396 0.448,0.313 12 false *A
*A for Bank 1


Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration.

NOTICE:

Be sure to loosen the chain sub-assembly between the banks.



e.

Remove the chain sub-assembly.


Hide 13530 41.REMOVE IDLE SPROCKET ASSEMBLY

a.
A129695

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.


Hide 13561 42.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A129696

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 43.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.

Remove the 2 No. 2 chain vibration dampers.


Hide 13521 44.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A109720

Remove the crankshaft timing sprocket from the crankshaft.


b.

Remove the 2 pulley set keys from the crankshaft.


Hide 45.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

Hide 13550 46.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 47.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

Hide 13512 49.REMOVE NO. 2 CAMSHAFT

Hide 11103C 50.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 51.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

Hide 13560A 52.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 53.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

Hide 13053 54.REMOVE NO. 3 CAMSHAFT

Hide 13054 55.REMOVE NO. 4 CAMSHAFT

Hide 11104A 56.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13801 57.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 58.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 60.REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

Hide 11115 61.REMOVE CYLINDER HEAD GASKET RH

Hide 11102 62.REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

Hide 11116 63.REMOVE CYLINDER HEAD GASKET LH

Hide 16322 64.REMOVE WATER INLET PIPE

a.

Slide the clip and disconnect the No. 1 water by-pass hose from the water inlet pipe.


b.
A320112

Remove the 2 bolts and water inlet pipe.