Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE UNIT › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109583 ENGINE UNIT G

2GR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A125485

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.
A286731C08
1.094,0.75 1.573,0.479 true 1.948,0.49 2.417,0.698 true 0.948,1.188 1.615,0.917 true 1.885,0.938 2.521,1.094 true 1.021,1.448 1.615,1.313 true 1.885,1.313 2.469,1.417 true 0.896,1.844 1.625,1.781 true 1.885,1.781 2.573,1.875 true 0.802,2.313 1.635,2.5 true 1.917,2.5 2.698,2.281 true 0.781,2.771 0.781,2.49 true 2.698,2.76 2.698,2.479 true 1.333,3.333 1.521,2.844 true 1.688,1.229 2,1.385 0.313,0.156 10 false *b 1.719,2.438 2.031,2.667 0.313,0.229 10 false *c 1.698,1.708 2.01,1.865 0.313,0.156 10 false *f 0.708,2.792 1.104,3.073 0.396,0.281 10 false *g 0.688,0.229 1,0.385 0.313,0.156 10 false *d 2.635,0.229 2.948,0.385 0.313,0.156 10 false *e 1.688,0.833 2,0.99 0.313,0.156 10 false *a 1.563,2.75 2.021,2.948 0.458,0.198 10 false SST 1.625,0.396 2.083,0.594 0.458,0.198 10 false SST 2.625,2.792 3.115,3.167 0.49,0.375 10 false *g
*a Tapered Path
*b Plunger
*c Check Ball
*d Correct
*e Incorrect
*f Low Pressure Chamber
*g High Pressure Chamber


Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 13511 3.INSPECT CAMSHAFT

a.

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.
A120669

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.04 mm (0.00157 in.)


If the runout is more than the maximum, replace the camshaft.

HINT:

Check the oil clearance after replacing the camshaft.




b.
A109632

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
Intake camshaft 44.316 to 44.416 mm (1.7448 to 1.7486 in.)
Exhaust camshaft 44.262 to 44.362 mm (1.7426 to 1.7465 in.)


Minimum Cam Lobe Height:
Item Specified Condition
Intake camshaft 44.166 mm (1.7388 in.)
Exhaust camshaft 44.112 mm (1.7366 in.)


If the cam lobe height is less than the minimum, replace the camshaft.


c.
A109633

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 35.946 to 35.960 mm (1.4152 to 1.4157 in.)
Other journals 25.959 to 25.975 mm (1.0221 to 1.0226 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 13050 4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Secure the camshaft in a vise.

NOTICE:

Be careful not to damage the camshaft in the vise.



b.
A314944C01
1.469,1.01 1.854,0.292 false 1.156,0.979 0.708,0.302 false 1.854,0.125 2.167,0.323 0.313,0.198 10 false *a 0.542,0.125 0.854,0.323 0.313,0.198 10 false *b
*a Knock Pin
*b Pin Hole


Align and fit the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly.


c.

Check that there is no gap between the camshaft timing gear assembly flange and the camshaft.


d.
A109634

Tighten the bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Check the lock of the camshaft timing gear assembly.


f.
A106100C07
1.875,1.063 2.479,1.083 2.479,1.083 1.813,1.125 false 1.594,1 0.906,1.021 0.906,1.021 1.615,1.042 false 2.073,2.771 2.583,3.063 false 2.083,3.302 2.594,3.583 false 1.979,3.438 2.354,4.385 2.354,4.385 1.49,3.094 false 1.323,3.125 0.729,3.5 false 1.302,2.875 0.74,3.031 false 1.208,3.771 0.938,4.375 false 2.313,4.406 3.063,4.604 0.75,0.198 10 false *d 2.542,1 3.365,1.406 0.823,0.406 10 false *b 0.813,4.396 1.469,4.604 0.656,0.208 10 false *c 0.708,0.927 1.104,1.375 0.396,0.448 10 false *a 2.635,3.542 3.208,3.75 0.573,0.208 10 false *e 0.552,2.979 0.948,3.188 0.396,0.208 10 false *e 0.552,3.438 0.948,3.656 0.396,0.219 10 false *f 2.625,3.021 3.198,3.24 0.573,0.219 10 false *f
*a Advance Side Path
*b Retard Side Path
*c Vinyl Tape
*d Rubber Piece
*e Closed
*f Open


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the camshaft. Plug 2 paths with rubber pieces.



ii.

Make a hole in the tape on the advance side path and the retard side path on the opposite side of the groove as shown in the illustration.


iii.
A106101C07
1.583,0.948 1.208,0.188 false 2.271,0.438 1.844,1.052 false 2.292,0.323 2.771,0.646 0.479,0.323 10 false *b 1.01,0.083 1.417,0.333 0.406,0.25 10 false *a
*a Advance Side Path
*b Retard Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 open paths (the advance side path and the retard side path).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



iv.
A106102C07
1.042,0.521 1.573,1.031 false 2.333,0.479 1.865,1.125 false 2.354,0.354 2.708,0.646 0.354,0.292 10 false *b 0.844,0.396 1.031,0.604 0.188,0.208 10 false *a 2.406,1.552 2.594,1.75 0.188,0.198 10 false *d 0.813,1.542 1.01,1.74 0.198,0.198 10 false *c
*a Advance Side Path
*b Retard Side Path
*c Hold Pressure
*d Decompress


Check that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard side path.

HINT:

The lock pin is released and the camshaft timing gear assembly turns in the advance direction.



v.

When the camshaft timing gear assembly moves to the most advanced position, release the air pressure from the retard side path, and then from the advance side path.

NOTICE:

Be sure to release the air pressure from the retard side path first. If the air pressure of the advance side path is released first, the camshaft timing gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




g.

Check for smooth rotation.

i.

Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.

NOTICE:

Do not use air pressure to perform the smooth operation check.




h.

Check the lock at the most retarded position.


i.
A314810C01
1.865,0.958 1.99,0.469 true 0.458,1.875 0.323,1.604 false 1.354,1.24 1.667,1.885 1.667,1.885 1.146,1.625 false 0.917,0.969 0.646,0.469 false 1.958,0.313 2.271,0.51 0.313,0.198 10 false *a 0.5,0.313 0.813,0.51 0.313,0.198 10 false *c 0.458,1.906 0.771,2.104 0.313,0.198 10 false *b 1.656,1.906 1.969,2.104 0.313,0.198 10 false *c
*a Knock Pin
*b Bolt
*c Do not remove


Remove the bolt and camshaft timing gear assembly.

NOTICE:

Do not remove the other 3 bolts.



Hide 13080 5.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Clamp the camshaft in a vise.

NOTICE:

Be careful not to damage the camshaft in the vise.



b.
A314944C01
1.469,1.01 1.854,0.292 false 1.156,0.979 0.708,0.302 false 1.854,0.125 2.167,0.323 0.313,0.198 10 false *a 0.542,0.125 0.854,0.323 0.313,0.198 10 false *b
*a Knock Pin
*b Pin Hole


Align and fit the knock pin of the camshaft with the pin hole of the camshaft timing exhaust gear assembly.


c.

Check that there is no gap between the camshaft timing exhaust gear assembly flange and the camshaft.


d.
A107564

Tighten the bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Check the lock of the camshaft timing exhaust gear assembly.


f.
A106103C08
1.323,2.75 0.75,2.875 false 1.323,3.292 0.75,3.542 false 2.073,3.115 2.625,3.458 false 2.094,2.927 2.615,3.083 false 1.354,3.417 1.292,4.406 1.292,4.406 1.938,3.073 false 2.104,3.771 2.302,4.406 false 1.594,0.958 0.969,0.979 0.969,0.979 1.573,1 false 1.833,1.01 2.396,1.021 2.396,1.021 1.823,1.063 false 1.198,4.427 1.948,4.625 0.75,0.198 10 false *c 0.771,0.896 1.177,1.292 0.406,0.396 10 false *a 2.24,4.438 2.792,4.667 0.552,0.229 10 false *d 2.448,0.938 3.104,1.365 0.656,0.427 10 false *b 2.667,3.052 3.24,3.26 0.573,0.208 10 false *f 0.563,3.49 0.927,3.698 0.365,0.208 10 false *f 0.563,2.813 0.927,3.031 0.365,0.219 10 false *e 2.667,3.427 3.24,3.646 0.573,0.219 10 false *e
*a Retard Side Path
*b Advance Side Path
*c Rubber Piece
*d Vinyl Tape
*e Open
*f Closed


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the camshaft. Plug 2 paths with rubber pieces.



ii.

Make a hole in the tape on the advance side path and the retard side path on the opposite side of the groove as shown in the illustration.


iii.
A106104C07
0.969,0.323 1.583,1.031 false 2.375,0.313 1.875,0.938 false 0.76,0.219 1.104,0.406 0.344,0.188 10 false *a 2.396,0.198 2.823,0.531 0.427,0.333 10 false *b
*a Advance Side Path
*b Retard Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 open paths (the advance side path and the retard side path).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



iv.
A106105C07
0.865,0.375 1.594,1.125 false 2.396,0.313 1.875,1.01 false 2.438,0.208 2.802,0.563 0.365,0.354 10 false *b 0.646,0.281 1.031,0.552 0.385,0.271 10 false *a 2.458,1.552 2.833,1.844 0.375,0.292 10 false *d 0.833,1.604 1.313,1.958 0.479,0.354 10 false *c
*a Advance Side Path
*b Retard Side Path
*c Decompress
*d Hold Pressure


Check that the camshaft timing exhaust gear assembly rotates in the retard direction when reducing the air pressure applied to the advance side path.

HINT:

The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.



v.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, and then from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




g.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advance position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the camshaft timing exhaust gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




h.

Check the lock at the most advanced position.


i.
A314811C01
1.854,1.052 1.99,0.5 false 1.042,1.521 0.479,0.49 0.479,0.49 1.073,1.073 false 0.792,1.844 0.573,1.656 false 1.333,1.271 1.813,1.833 1.813,1.833 1.333,1.656 false 1.969,0.302 2.458,0.667 0.49,0.365 10 false *a 0.354,0.302 0.792,0.646 0.438,0.344 10 false *c 1.865,1.823 2.344,2.125 0.479,0.302 10 false *c 0.844,1.823 1.177,2.052 0.333,0.229 10 false *b
*a Knock Pin
*b Bolt
*c Do not remove


Remove the bolt and camshaft timing exhaust gear assembly.

NOTICE:

Do not remove the other 4 bolts.



Hide 11101A 6.INSPECT CYLINDER HEAD SET BOLT

a.
A192409C03
1.156,1.448 1.719,1.625 0.563,0.177 10 false 103 mm 2.25,0.323 2.521,0.5 0.271,0.177 10 false *a
*a Measurement Point


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard Diameter:

10.85 to 11.00 mm (0.4272 to 0.4330 in.)


Minimum Diameter:

10.70 mm (0.4212 in.)


Measurement Point (distance from the seat):

103 mm (4.06 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt. Failure to do so may lead to engine damage.


·

If there is any thread deformation, replace the cylinder head set bolt with a new one.




Hide 13506 7.INSPECT CHAIN SUB-ASSEMBLY

a.
A315337C01
1.521,1.052 1.833,1.25 0.313,0.198 10 false *a 0.833,1.948 0.99,2.146 0.156,0.198 10 false 1 0.615,1.948 0.771,2.146 0.156,0.198 10 false 0 1.063,1.948 1.219,2.146 0.156,0.198 10 false 2 1.281,1.948 1.438,2.146 0.156,0.198 10 false 3 1.5,1.948 1.656,2.146 0.156,0.198 10 false 4 2.573,1.948 2.885,2.146 0.313,0.198 10 false 15 2.354,1.948 2.667,2.146 0.313,0.198 10 false 14 2.135,1.948 2.448,2.146 0.313,0.198 10 false 13 1.906,1.948 2.219,2.146 0.313,0.198 10 false 12
*a Measurement Length


Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

136.9 mm (5.389 in.)


HINT:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is more than the maximum, replace the chain sub-assembly.


Hide 13507 8.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A315337C01
1.521,1.052 1.833,1.25 0.313,0.198 10 false *a 0.833,1.948 0.99,2.146 0.156,0.198 10 false 1 0.615,1.948 0.771,2.146 0.156,0.198 10 false 0 1.063,1.948 1.219,2.146 0.156,0.198 10 false 2 1.281,1.948 1.438,2.146 0.156,0.198 10 false 3 1.5,1.948 1.656,2.146 0.156,0.198 10 false 4 2.573,1.948 2.885,2.146 0.313,0.198 10 false 15 2.354,1.948 2.667,2.146 0.313,0.198 10 false 14 2.135,1.948 2.448,2.146 0.313,0.198 10 false 13 1.906,1.948 2.219,2.146 0.313,0.198 10 false 12
*a Measurement Length


Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

137.6 mm (5.417 in.)


HINT:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is more than the maximum, replace the No. 2 chain sub-assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.

Place the chain sub-assembly around the crankshaft timing sprocket.


b.
A109646

Using a vernier caliper, measure the diameter of the crankshaft timing sprocket with the chain sub-assembly.

Minimum Sprocket Diameter (with Chain):

61.4 mm (2.418 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.


Hide 13530 10.INSPECT IDLE SPROCKET ASSEMBLY

a.

Place the chain sub-assembly around the idle sprocket assembly.


b.
A109647

Using a vernier caliper, measure the diameter of the idle sprocket assembly with the chain sub-assembly.

Minimum Sprocket Diameter (with Chain):

61.4 mm (2.418 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain sub-assembly and idle sprocket assembly.


Hide 11.INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE

a.
A109648

Using a micrometer, measure the diameter of the No. 1 idle gear shaft.

Standard No. 1 Idle Gear Shaft Diameter:

22.987 to 23.000 mm (0.9050 to 0.9055 in.)



b.
A120673

Using a caliper gauge, measure the inside diameter of the idle sprocket assembly.

Standard Idle Sprocket Assembly Inside Diameter:

23.020 to 23.030 mm (0.9063 to 0.9067 in.)



c.

Subtract the No. 1 idle gear shaft diameter measurement from the idle sprocket assembly inside diameter measurement.

Standard Oil Clearance:

0.020 to 0.043 mm (0.000787 to 0.00169 in.)


Maximum Oil Clearance:

0.093 mm (0.00366 in.)


If the oil clearance is more than the maximum, replace the No. 1 idle gear shaft and idle sprocket assembly.


Hide 13540 12.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A314812C01
2.156,0.781 2.427,0.51 false 1.479,1.583 1.854,1.927 false 2.438,0.354 2.75,0.552 0.313,0.198 10 false *a 1.896,1.854 2.208,2.052 0.313,0.198 10 false *b
*a Plunger
*b Stopper Plate


Move the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.

If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.


Hide 13550 13.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A314946C01
0.344,1.594 0.656,1.792 0.313,0.198 10 false *a 2.927,0.729 3.24,0.927 0.313,0.198 10 false *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the wear depth of the No. 2 chain tensioner assembly.

Maximum Depth:

0.9 mm (0.0354 in.)


If the depth is more than the maximum, replace the No. 2 chain tensioner assembly.


Hide 13560A 14.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A314947C01
2.938,0.74 3.25,0.938 0.313,0.198 10 false *a 0.292,1.615 0.604,1.813 0.313,0.198 10 false *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the wear depth of the No. 3 chain tensioner assembly.

Maximum Depth:

0.9 mm (0.0354 in.)


If the depth is more than the maximum, replace the No. 3 chain tensioner assembly.


Hide 13559 15.INSPECT CHAIN TENSIONER SLIPPER

a.
A106110C04
3,1.354 3.229,1.563 0.229,0.208 10 false *a
*a Depth


Measure the wear depth of the chain tensioner slipper.

Maximum Depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the chain tensioner slipper.


Hide 13561 16.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A106111C04
2.927,1.333 3.333,1.542 0.406,0.208 10 false *a
*a Depth


Using a vernier caliper, measure the wear depth of the No. 1 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13562 17.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A106112C04
2,1.417 2.573,1.677 0.573,0.26 10 false *a
*a Depth


Using a vernier caliper, measure the wear depth of the No. 2 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 2 chain vibration damper.


Hide 18.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Inspect the camshaft thrust clearance (for Bank 1).


ii.
A109682

Using a dial indicator, measure the thrust clearance while moving each camshaft back and forth.

Standard Thrust Clearance:

0.08 to 0.13 mm (0.00315 to 0.00512 in.)


Maximum Thrust Clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly RH. If the thrust surface is damaged, replace the camshaft.



b.

Inspect the camshaft thrust clearance (for Bank 2).


ii.

Using a dial indicator, measure thrust clearance while moving each camshaft back and forth.

Standard Thrust Clearance:

0.08 to 0.13 mm (0.00315 to 0.00512 in.)


Maximum Thrust Clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly LH. If the thrust surface is damaged, replace the camshaft.



Hide 19.INSPECT CAMSHAFT OIL CLEARANCE (for Bank 1)

a.

Clean the camshaft bearing caps, camshaft housing sub-assembly RH and camshaft journals.


b.

Place the camshafts on the camshaft housing sub-assembly RH.


c.
A120715C06
1.583,0.99 1.385,1.74 false 1.302,1.771 1.625,1.979 0.323,0.208 10 false *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



e.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


f.
A129756C04
1.479,1.073 1.156,1.802 1.156,1.802 1.01,1.802 false 2.844,3.115 2.458,2.417 2.458,2.417 2.302,2.417 false 2.458,2.417 2.854,3.906 false 0.344,2.208 0.542,2.208 0.542,2.208 2.146,3.083 false 1.344,3.094 0.542,2.219 false 0.542,2.229 0.542,3.115 false 0.552,3.917 1.354,4.417 1.354,4.417 2.146,3.917 false 1.354,3.927 1.354,4.417 false 0.813,1.719 1.135,1.948 0.323,0.229 10 false *a 2.104,2.323 2.396,2.625 0.292,0.302 10 false *b 0.135,2.146 0.667,2.552 0.531,0.406 10 false *c 1.281,4.438 1.573,4.646 0.292,0.208 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.032 to 0.063 mm (0.00126 to 0.00248 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.09 mm (0.00354 in.)


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly RH.


Hide 20.INSPECT CAMSHAFT OIL CLEARANCE (for Bank 2)

a.

Clean the camshaft bearing caps, camshaft housing sub-assembly LH and camshaft journals.


b.

Place the camshafts on the camshaft housing sub-assembly LH.


c.
A120717C05
1.813,0.708 1.438,0.156 false 1.26,0.063 1.625,0.354 0.365,0.292 10 false *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



e.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


f.
A129758C03
1.76,0.771 0.979,0.24 false 0.552,2.99 1.052,2.354 1.052,2.354 0.615,3.656 false 1.427,3 2.25,2.354 2.25,2.354 2.094,3.01 false 1.427,3.708 2.135,4.167 2.135,4.167 2.792,3.708 false 2.792,2.979 2.26,2.365 false 2.135,4.156 2.104,3.688 false 0.75,0.146 1.167,0.438 0.417,0.292 10 false *a 1.094,2.219 1.385,2.458 0.292,0.24 10 false *b 2.313,2.24 2.646,2.563 0.333,0.323 10 false *c 2.031,4.198 2.635,4.667 0.604,0.469 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.032 to 0.063 mm (0.00126 to 0.00248 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.09 mm (0.00354 in.)


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly LH.


Hide 17105 21.INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst)

a.
A134936

Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head sub-assembly LH.

Maximum Warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold sub-assembly LH (TWC: Front Catalyst).


Hide 17104 22.INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst)

a.
A134937

Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head sub-assembly RH.

Maximum Warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold sub-assembly RH (TWC: Front Catalyst).


Hide 17111 23.INSPECT INTAKE MANIFOLD

A134934C03
0.125,0.083 0.583,0.417 0.458,0.333 10 false *a 0.156,2.073 0.542,2.406 0.385,0.333 10 false *b
*A Cylinder Head Side
*B Surge Tank Side


a.

Cylinder head side:

i.

Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head sub-assembly.

Maximum Warpage:

0.1 mm (0.00394 in.)


If the warpage is more than the maximum, replace the intake manifold.



b.

Surge tank side:

i.

Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the surge tank.

Maximum Warpage:

0.1 mm (0.00394 in.)


If the warpage is more than the maximum, replace the intake manifold.