Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0109989 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

NOTICE:

When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B355799

Engage the 3 clamps to connect the airbag wire harness.


d.

Install the curtain shield airbag assembly with 5 new bolts, 9 new clips with pins and 2 new spacers, and engage the 2 hooks and 2 clips in the order shown in the illustration.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.


HINT:

Engage the 2 claws to install each new clip.


B355801C01
6.365,0.365 7.063,0.365 7.063,0.365 7.063,1.177 false 6.5,0.813 6.5,0.365 false 3.917,2.146 4.146,2.146 true 1.948,2.24 2.094,2.5 2.094,2.5 2.24,2.5 false 1.833,1.74 2.063,1.74 true 4.167,2.063 4.479,2.219 0.313,0.156 10 false *1 2.26,2.417 2.573,2.573 0.313,0.156 10 false *2 2.083,1.646 2.396,1.802 0.313,0.156 10 false *a 6.177,0.26 6.344,0.448 0.167,0.188 10 true *b 0.552,0.438 0.708,0.635 0.156,0.198 10 true 1 0.771,0.438 0.875,0.625 0.104,0.188 10 true 3 2.177,0.073 2.323,0.24 0.146,0.167 10 true 4 2.625,0.052 2.771,0.219 0.146,0.167 10 true 5 3.833,0.052 3.979,0.219 0.146,0.167 10 true 6 3.26,0.031 3.406,0.198 0.146,0.167 10 true 7 1.135,0.01 1.281,0.177 0.146,0.167 10 true 8 0.646,0.021 0.76,0.198 0.115,0.177 10 true 9 1.219,0.438 1.365,0.604 0.146,0.167 10 true 2 0.271,0.021 0.448,0.198 0.177,0.177 10 true 10 0.292,0.802 0.469,0.979 0.177,0.177 10 true 11 1.656,0.792 1.875,0.979 0.219,0.188 10 true 12 5.896,0.281 6.115,0.469 0.219,0.188 10 true 13 5.083,0.031 5.302,0.219 0.219,0.188 10 true 14 4.542,0.042 4.76,0.229 0.219,0.188 10 true 15 5.521,0.146 5.74,0.333 0.219,0.188 10 true 16 6.542,0.625 6.719,0.792 0.177,0.167 10 true 17 6.865,0.906 7.042,1.073 0.177,0.167 10 true 18
*1 Pin *2 Spacer
*a Clip *b Spacer Location



e.

Using needle nose pliers, push the 9 pins into the 9 clips.

NOTICE:
·

Do not damage the pins.

·

Make sure that the pins of the clips are pushed in firmly.




f.
B355798C01
2.396,0.583 2.083,0.854 true 0.969,2.01 0.427,2.01 true 0.25,1.906 0.427,2.104 0.177,0.198 10 true *a 1.938,0.813 2.25,0.969 0.313,0.156 10 false *b
*a Airbag Connector
*b Airbag Connector Lock


Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



g.

Push in the airbag connector lock to install the airbag connector.


Hide 62972C 2.INSTALL NO. 1 ROOF SIDE AIR DUCT (for Normal Roof)

a.

Engage the clip (B).


b.

Install the No. 1 roof side air duct with the 2 clips (A).


Hide 62972C 3.INSTALL NO. 1 ROOF SIDE AIR DUCT (for Sliding Roof)

a.

Engage the clip (B).


b.

Install the No. 1 roof side air duct with the clip (A).


Hide 4.CONNECT SLIDING ROOF DRAIN HOSE (for Sliding Roof)

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 6.INSTALL ROOF HEADLINING ASSEMBLY